Kinetic and Thermodynamic Study for Fenton-Like Oxidation of Amaranth Red Dye


Oxidation by Fenton like reactions (Fe3+/H2O2) is economically process for destructive hazardous pollutants in waste water. The effects of different parameters such as, amaranth red dye, ferric chloride, hydrogen peroxide concentrations, pH value of solution, temperature and the presence of inorganic ions (carbonate, nitrate, chloride) on oxidative decolorization of amaranth were investigated. Amaranth degradation by (Fe3+/H2O2) reagent was found to follow first order kinetic model. Under optimum condition, pH = 2.6 and [FeCl3] = 3.75 × 10-4 mol·dm-3, the amaranth in aqueous solution with an initial concentration of 5 × 10-5 mol·dm-3 was degraded by 95% within 6 minutes. Increasing temperature in the range of 298 - 308 K increases the rate of dye degradation. Thermodynamic constants, ΔH*, ΔS* and ΔG* were evaluated. The results implied that the oxidation process was favorable and endothermic.

Share and Cite:

Abou-Gamra, Z. (2014) Kinetic and Thermodynamic Study for Fenton-Like Oxidation of Amaranth Red Dye. Advances in Chemical Engineering and Science, 4, 285-291. doi: 10.4236/aces.2014.43031.

1. Introduction

The need of industry for dye has shown a high pollutant potential, specially the use of azodyes [1] , for example, tartrazine [2] , amaranth [3] and others. Amaranth is used as food dye; cosmetic dye and can applied for natural and synthetic fibers, leather, paper, phenol formaldehyde resins [4] . The FDA in the United States has banned amaranth and it is also banned in Russia, Norway and Austria [5] . Owing to their toxicity, many studies have been done to remove them from water source. Biological (biodegradation) [6] and chemical methods (chlorination, ozonation) [7] are the most frequently used methods for removal of dyes from effluent water streams. But, these traditional processes for treatment of the effluents prove to be insufficient to purify waste water after the different operations of waste waters dyeing and washing.

Advanced oxidation processes (AOPs) are alternative methods for the complete degradation of dye. The usage of the advanced oxidation processes (AOPs) have improved during the last decade since they are able to eliminate the problem of dye destruction in aqueous systems. AOPs were based on the generation of very reactive species such as hydroxyl radicals (•OH) that oxidize a broad range of pollutants quickly and non-selectively. AOPs such as Fenton and Photo-Fenton catalytic reactions [8] [9] , H2O2/UV processes [9] .

The aim of this work was to find out the potential of Fenton-like for the decolorization of amaranth as model azo dye and examine the effect of the major system parameters on the decolorization kinetics of amaranth dye. Such parameters are the pH, concentration of ferric chloride, H2O2, dye and temperature of ambient. Also the study gave attention to the effect some inorganic electrolytes.

2. Experimental

2.1. Reagents and Materials

All chemicals were of pure grade and were used without further purification. Amaranth Red purchased from Fisher Scientific company chemical manufacturing division Fair town, New Jersey (molecular weight = 604.47, lmax = 520 nm). The chemical structure and uv-vis spectrum of amaranth red dye is given in Figure 1. FeCl3, NaCl, NaNO3 and Na2CO3 were purchased from Merck. Hydrogen peroxide solution (35%) was of analytical grade. All solutions were prepared using bidistilled water. Stock solutions of dye (1 mM), FeCl3 (10mM) were prepared in 0.01 M of HCl. All experiments were performed at pH below 3.

2.2. Kinetic Experiments

The kinetic measurements were carried out spectrophotometrically using 292 Cecil spectrophotometer was equipped with constant temperature cell holder attached to thermostatic controlled bath with temperature stability of ±0.1˚C. The reactants were thermostated for 15 min, then mixed thoroughly and quickly transferred to an absorption cell. The progress of the reaction was monitored at 520 nm. The pH of the reaction was adjusted using Griffin pH-meter fitted with a combined glass calomel electrode.

3. Results and Discussion

The present study concerns with the oxidative decolorization of amaranth by Fenton-like reaction. The absorbance of amaranth at λmax = 520 nm decreased with time as shown in Figure 2. The kinetics measurements were carried out under pseudo first order conditions, where hydrogen peroxide concentration was in excess than that of dye. The plot of logarithmic absorbance vs. time was linear. This indicates the pseudo first-order kinetics of the reaction with respect to the Amaranth concentration.

Figure 1. Chemical structure, uv-vis spectrum of amaranth red dye. [dye] = 5 × 10−5 mol∙dm−3.

Figure 2. The change in absorbance of amaranth vs time at l = 520 nm. [dye] = 5 × 105 mol∙dm3, [H2O2] = 5 × 103 mol∙dm3, [Fe3+] = 5 × 104 mol∙dm3 and pH = 2.6.

3.1. Effect of pH

Advanced oxidation processes are powerful alternative methods of wastewater treatment. This method based on the production of powerful oxidant, HO. (E = 2.8 V versus NHE). These radicals are capable to degrade recalcitrant organic compounds under mild experimental conditions [10] . The general mechanism of Fenton reaction [11] is


Then, Fe3+ ions can be reduced by excess H2O2 to form Fe2+ ions and more HO. radicals. Second reaction is called Fenton-like [12] allowing Fe2+ regeneration leading to catalytic mechanism (reactions, 2 - 6),








As clear from above mechanism the amount of HO. depends on the pH of solution. The effect of pH was studied in pH range of 2 - 3. The results showed that increasing pH from 2 to 2.6 ± 0.1 increases the observed rate constant, kobs, from 0.45 × 10−3 s−1 to 8.9 × 10−3 s−1 (Figure 3). The drastic decrease in the rate of decolorization at pH = 2 is attributed to drastic reduction of hydroxyl radicals resulted from the stabilization of hydrogen peroxide. Also Figure 3 showed that increasing pH above 2.6 decreases the observed rate constant. Therefore, the optimal pH value for the decolorization of amaranth is 2.6. This is in agreement with earlier results [8] [11] -[15] . These studies showed that there is optimum pH value (pH = 3).

3.2. Effect of Ferric Chloride Concentration

No reaction was observed between amaranth and hydrogen peroxide in absence of ferric ions. Ferric ion concentration shows acceleration effect on the decolorization rate of amaranth. Keeping temperature at 35˚C, [dye] = 5 ´ 10−5 mol∙dm−3 and [H2O2] = 5 ´ 10−3 mol∙dm−3 using different concentrations of ferric chloride namely, 1 - 3.75 ´ 10−4 mol∙dm−3, the decolorization rate increased by increasing ferric ions concentrations. This is attributed to increase HO. concentrations. Above that concentration the rate decreased, Figure 4. This could be at-

Figure 3. First order plots for decolorization of amaranth at various pH. [dye] = 5 × 105 mol∙dm3, [H2O2] = 5 × 103 mol∙dm3, [Fe3+] = 5 × 104 mol∙dm3 and T= 35˚C.

Figure 4. First order plots for decolorization of amaranth at various Fe3+ concentrations. [dye] = 5 × 10−5 mol∙dm−3, [H2O2] = 5 × 10−3 mol∙dm−3, pH = 2.65 and T = 35˚C.

tributed to the increasing in [Fe3+] increases [Fe2+] which scavenging the HO. [8] [15] . Maximum rate at [Fe3+] = 3.75 ´ 10−4 mol×dm−3, almost, 95% color removed was observed. Khataee et al. [16] reported that increasing the concentration of Fe3+ ions increases the decolorization rate of brilliant blue and maximum rate was at [Fe3+] = 2 ´ 10−4 mol∙dm−3.

3.3. Effect of H2O2 Concentration

The effect of hydrogen peroxide concentration on the rate of decolorization of amaranth studied at pH equals 2, [dye] = 5 ´ 10−5 mol×dm−3 and [Fe3+] = 5 ´ 10−4 mol×dm−3. Figure 5 showed that the decrease in dye concentration as function of time was dependent of hydrogen peroxide concentration. Increases of hydrogen peroxide concentrations in range of 5 - 25 ´ 10−3 mol∙dm−3 increases the rate constant of decolorization from 0.5 ´ 10−3 to 2 ´ 10−3 s−1. This is due to the increase of HO. radicals [8] [15] . Plot of lnkobs versus ln[H2O2] yields straight line with slope of unity indicates the reaction is first order in hydrogen peroxide.

3.4. Effect of Amaranth Concentration

The effect of initial dye concentration of aqueous solution of amaranth on Fenton-like process was investigated since pollutant concentration is important parameter in wastewater treatment. Increasing the initial amaranth concentration from 2 to 4 × 10−5 mol∙dm−3 did not show any effect on the decolorization rate, Figure 6. Also

Figure 5. First order plots for decolorization of amaranth at various H2O2 concentrations. [dye] = 5 × 10−5 mol∙dm−3, [Fe3+] = 5 × 104 mol∙dm−3, T = 35˚C and pH = 2.

Figure 6. First order plots for decolorization of amaranth at various dye concentrations. [H2O2] = 5 × 103 mol∙dm−3, [Fe3+] = 5 × 104 mol∙dm−3, T = 30˚C and pH = 2.65.

Figure 6 shows that increasing the concentration of dye above (4 × 10−5 mol∙dm−3) decrease the rate of decolorization. This attributed to relatively lower of HO. results from the increasing of amaranth concentration while concentration of H2O2 and Fe3+ remains the same. The obtained results were in good agreement with earlier reported [11] [13] -[15] .

3.5. Effect of Temperature

The variation of the temperature in range of 298 - 308 K increases the rate of decolorization of amaranth. No optimal temperature in this study was detected as opposed to the literature reports [17] [18] in which 30˚C are stated as optimal temperature for Fenton oxidation. Another optimal temperature, 50˚C was reported on decolorization of some dyes by Fenton-like reaction [8] . The activation energy was calculated from Arrhenius plot and Eyring equation and was found to be 104.79 kJ∙mol−1. The other thermodynamic parameters are given in Table1 As observed from Table 1 positive value of ΔS* indicates reaction is favor. The ΔH* positive value indicates that the process is endothermic.

3.6. Effect of Inorganic Anion Concentration

Inorganic anions occur naturally in waste water (e.g.) or may be added to facilitate the dyeing (e.g. Cl and). The presence of inorganic anions in textile wastewaters plays an important role in the oxidation kinetics of different dyes. Inorganic anions may induce or reduce the rate of oxidation.

3.6.1. Influence of NaNO3 Concentration

Decolorization rate of amaranth did not affect by addition of NaNO3 (Table 2).

3.6.2. Influence of Na2CO3 Concentration

Different concentrations of Na2CO3 were used to study the effect of carbonate ions on the oxidation of amaranth. Carbonate ions were present mainly as H2CO3, since the experiments were performed at pH ≤ 3. Presence of bicarbonate ions in the course of oxidation may decrease the decolorization rate due to scavenging of OH by . Production of which is less reactive than hydroxyl radical [19] lowered the levels of .OH during the course of the reaction hence decreasing the decolorization rate. It was observed that the decolorization rate constant (5.295 × 10−3 s−1) in the absence of carbonate ions decreased to 1.74 × 10−3 s−1 due to the presence of 8 × 10−3 mol∙dm−3 Na2CO3, Table2

3.6.3. Influence of NaCl Concentration

Addition of 0.085 mol∙dm−3 of NaCl decreased rate constant from 5.32 × 10−3 s−1 (in absence of chloride) to 1.6 × 10−3 s−1. The inhibitive effect of chloride can be explained by scavenging effect of chloride ion on .OH (Equation (9)).


Increasing the concentration of chloride up to 0.340 mol∙dm−3 had no significant effect (Table 2). The obtained results were in good agreement with earlier reported [8] [11] [14] .

Table 1. Thermodynamic parameters for decolorization of Amaranth by Fenton-like reagent.

Table 2. Observed first order rate constants for the decolorization of Amaranth by Fenton-like reagent at temperature = 35˚C at different concentration of inorganic anions.

4. Conclusion

The decolorization kinetics of amaranth red in aqueous solution was studied using Fenton like reaction in dark environment. The results showed that the Fenton-like is powerful method for decolorization of amaranth red dye. The reaction was first order in dye and H2O2. The Fenton-like oxidation of amaranth red dye showed maximum rate at pH = 2.6 and [Fe3+] = 3.75 × 10−4 mol∙dm−3.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] Pereira, W.S. and Freire, R.S. (2006) Azo Dye Degradation by Recycled Waste Zero-Valent Iron Powder. Journal of the Brazilian Chemical Society, 17, 832-838.
[2] Vidotti, E.C. and Rollemberg, M.C.E. (2006) Derivative Spectrophotometry: A Simple Strategy for Simultaneous Determination of Food Dyes. Quimica Nova, 29, 230-233.
[3] Keck, A., Klein, J., Kudlich, M., Stolz, A., Knackmuss, H.J. and Mattes, R. (1997) Reduction of Azo Dyes by Redox Mediators Originating in the Naphthalenesulfonic Acid Degradation Pathway of Phi
ngomonas Sp. Strain BN6. Environmental Microbiology, 63, 3684-3690.
[4] Shu, H.Y. and Huang, C.R. (1995) Degradation of Commercial Azo Dyes in Water Using Ozonation and UV Enhanced Ozonationprocess. Chemosphere, 31, 3813-3825.
[5] Karkmaz, M., Puzenat, E., Guillard, C. and Herrmann, J.M. (2004) Photocatalytic Degradation of the Alimentary Azo Dye Amaranth Mineralization of the Azo Group to Nitrogen. Applied Catalysis B: Environmental, 51, 183-194.
[6] Ghodake, G., Jadhav, U., Tamboli, D., Kagalkar, A. and Govindwar, S. (2011) Decolorization of Textile Dyes and Degradation of Mono-Azo Dye Amaranth by Acinetobacter calcoaceticus NCIM 2890. Indian Journal of Microbiology, 51, 501-508.
[7] Burkinshaw, S.M. and Kabambe, O. (2009) Attempts to Reduce Water and Chemical Usage in the Removal of Reactive Dyes: Part 1 Bis(Aminochlorotriazine), Dyes. Dyes Pigments, 83, 363-374.
[8] Medien, H.A.A. and Khalil, S.M.E. (2010) Kinetics of the Oxidative Decolorization of Some Organic Dyes Utilizing Fenton-Like Reaction in Water. Journal of King Saud University (Science), 22, 147-153.
[9] Elmorsi, T.M., Riyad, Y.M., Mohamed, Z.H. and Abd El Bary, H.M.H. (2010) Decolorization of Mordant Red 73 Azo Dye in Water Using H2O2/UV and Photo-Fenton Treatment. Journal of Hazardous Materials, 174, 352-358.
[10] Parsons, S. (2004) Advanced Oxidation Processes for Water and Wastewater Treatment. IWA Publishing, London.
[11] Habib, Md., Ismail, I., Mahmood, A.J. and Ullah, Md. (2012) Decolorization and Mineralization of Brilliant Golden Yellow (BGY) by Fenton and Photo-Fenton Processes. African Journal of Pure and Applied Chemistry, 6, 153-158.
[12] Ensing, B., Buda, F. and Baerends, E.J. (2003) Fenton-Like Chemistry in Water: Oxidation Catalysis by Fe(III) and H2O2. Journal of Physical Chemistry A, 107, 5722-5731.
[13] Neamtua, M., Yediler, A., Siminiceanu, I. and Kettrup, A. (2003) Oxidation of Commercial Reactive Azo Dye Aqueous Solutions by the Photo-Fenton and Fenton-Like Processes. Journal of Photo-Chemistry and Photobiology A: Chemistry, 161, 87-93.
[14] Chen, C.-C., Wu, R.-J., Tzeng, Y.-Y. and Lu, C.-S. (2009) Chemical Oxidative Degradation of Acridine Orange Dye in Aqueous Solution by Fenton’s Reagent. Journal of the Chinese Chemical Society, 56, 1147-1155.
[15] Hashemian, S., Tabatabbaee, M. and Gafari, M. (2013) Fenton Oxidation of Methyl Violet in Aqueous Solution. Journal of Chemistry, 2013, Article ID: 509097.
[16] Khataee, A., Vatanpour, V. and Farajzadeh, M. (2008) Remediation of the Textile Dye Brilliant Blue FCF from Contaminated Water via a Fenton-Like Reaction: Influence of Aromatic Additives. Turkish Journal of Engineering and Environmental Sciences, 32, 367-376.
[17] Guedes Anabela, M.F.M., Madeira Luis, M.P., Boaventura Rui, A.R. and Costa Carlos, A.V. (2003) Fenton Oxidation of Cork Cooking Wastewater—Overall Kinetic Analysis. Water Research, 37, 3061-3069.
[18] Ramirez, J.H., Costa, C.A. and Madeira, L.M. (2005) Experimental Design to Optimize the Degradation of the Synthetic Dye Orange II Using Fenton’s Reagent. Catalysis Today, 107-108, 68-76.
[19] Buxton, G.V., Greenstock, C.L., Helman, W.P. and Ross, A.B., (1988) Critical-Review of Rate Constants for Reactions of Hydrated Electrons, Hydrogen-Atoms and Hydroxyl Radicals(•OH/•O–) in Aqueous-Solution. Journal of Physical and Chemical Reference Data, 17, 513-886.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.