Development of a Competitiveness Improvement Framework for Forensic Science Laboratories


This study presents a methodology used in developing the competitiveness improvement framework (CIF) for laboratories, in particular, Forensic Science Laboratories (FSLs). The cyclic nature of FSL processes allowed data collection for the purpose of identification of factors affecting FSL performance (cause factors). Flow charts were used to represent mathematical formulations for cause factor measurements and quantification of the baseline data on turnaround time (TAT), backlogs for case files (Bg), turnaround time in the supply chain (Tsc), and employee absenteeism (Ab). By quantifying the cause factors in addition to academic development coefficient (Ad) and complex longevity (Lc) for FSL employees, it was possible to establish the organizational design features requiring improvements. The relevance of cause factors to FSL stakeholders and means of improvement and sustainability were established. A detailed road map towards CIF was presented using D-MAIC methodology. The rated cause factors based on challenges in the FSL business environment were subjected to Pareto analysis to prioritize the challenges in order to improve FSLs’ competitiveness. The interrelationship between the three dimensions of competitiveness improvement (process, performance and planning) was presented in terms of the affected six cause factors. Also, the potential lean practices for improving competitiveness of FSL based on measured cause factors have been presented. This paper introduced methods and measures for improving operational competitiveness of laboratories. The CIF was finally presented in a form of a series of three flow charts summarizing all steps implemented in its development with inputs and cause factors involved.

Share and Cite:

Omari, G. , Manyele, S. and Mwaluko, G. (2019) Development of a Competitiveness Improvement Framework for Forensic Science Laboratories. Engineering, 11, 604-641. doi: 10.4236/eng.2019.119042.

1. Introduction

1.1. Need for Developing the Competitiveness Improvement Framework for FSL

The FSL consists of a series of connected processes beginning at SRO’s office (when samples arrive) and ending at the same area where clients collect their analytical reports. In this study, the critical performance measures and cause factors were identified in order to develop the CIF. The contribution of this study to the global knowledge is mainly on forensic science laboratory management, which is a new research area involving competitiveness improvement. After establishing the baseline performance data, the study scope was extended to locating areas of improvement and the approach.

The current structure of forensic science services in Tanzania is defined using the basic processes shown in Figure 1 (starting from a crime scene to judgment at a court of law). The study area started from the time samples/exhibits are submitted to the laboratory to the time when a report is released.

The competitiveness scenario of FSL focuses on differentiation of services from its competitors and elimination of customer complaints due to delayed reports (extended TAT and backlogs). It was important to use the lean principles (LPs) based on essential characteristics and power to identify the non-value added activities (NVAs) [1] .

1.2. Baseline Data on Cause Factors Affecting Competitiveness in the FSL

1.2.1. Case-File Backlogs Challenge

Case-file backlogs were identified as one of the cause factors affecting the competitiveness of the (FSL). Backlogs represent case-files that remain unprocessed or unreported within a selected time interval (year, week or month) which leads to increased customer complaints, rework, cost of analysis, degradation of biological samples, etc. Case-file backlogging was quantified in three consecutive years (Y2014 to Y2016) to study variations as case files are processed [2] [3] [4] [5] . Data were collected for the case-files received and case-files processed, difference of which gives case-files backlogged. The time interval for a case-file to be regarded as backlogged was one week, which can translate into backlogged case-files per month or year. A data collection tool was established and used for three laboratory disciplines (forensic chemistry, biology/DNA and toxicology).

The case-files received per week increased from 16.98 to 38.19 case-files between Y2014 and Y2016, respectively. It was observed that, case-files reported increased between Y2014 and Y2016 from 8.7 to 35.5 case files per week, respectively, leading to a decrease in backlogged case-files (from 10.7 to 2.1 case-files,

Figure 1. Process flow chart for forensic science services in Tanzania and the study area, identification.

respectively. The annual percentage of the case-files backlogged was highest for forensic toxicology (at 29.0%), while the highest number of case-files backlogged per week was observed for forensic chemistry (1.0 case-file per week), followed by forensic biology/DNA (at 0.77 case-files per week) in Y2016.

The number of case-files backlogged per analyst per year was highest in Y2014 and dropped continuously towards Y2016, being comparably higher in forensic biology/DNA (8.0 case-files per analyst per year) and chemistry (7.4 case-files per analyst per year). The effect of case-file backlogging on FSL competitiveness can be minimized by continued management effort in backlog elimination [6] [7] [8] .

1.2.2. Extended Turnaround Time during Case-File and Sample Processing

TAT is the total time interval from when a request for laboratory analysis is received until when the results are collected by the client [9] [10] . The performance of the FSL is affected by extended TAT in the case-file and sample processing steps. This has not been subjected to intensive research, necessitating critical analysis [11] [12] [13] [14] . The total TAT was obtained as the sum of measured time interval for each work station, six of which were studied [15] [16] . Extended TAT leads not only to customer complaints, but also paves way for customers to seek for services from competitors, leading to lost competitive edge for the FSL. This study was conducted to establish the baseline data on TAT (between Y2014 and Y2015) to enable implementation of corrective actions [14] . Six case-file processing steps were identified for which starting and completion times were recorded in dates, giving TAT values in days. The overall turnaround time (TTAT) was the highest for forensic biology/DNA compared to forensic chemistry and toxicology (137.7, 76.4 and 54.5 days on average, respectively). The laboratory analysis time (TAT2) was the longest of all six case-file processing steps (being 94.9, 31.8 and 10.4 days, for biology/DNA, toxicology and chemistry laboratories, respectively). The three major steps necessitating root-cause analysis and intervention to minimize TAT were analysis turnaround time (TAT2), report collection time (TAT6) and report review time (TAT4). It was concluded that the causes for extended TAT were within control by the FSL management, although financial and human resources were required to achieve the TAT reduction.

1.2.3. Employee Absenteeism in the FSL and Its Impact on Competitiveness

Absenteeism is a bigger problem affecting negatively the competitiveness of any laboratory [17] [18] [19] . A detailed analysis of the measured absenteeism data for employees in the FSL was conducted, using a sample size of 134 (78%) employees out of 172. While the availability of resources affects also the performance of the laboratory, absenteeism plays a vital role, worth exploring [20] [21] [22] [23] [24] . The factors assumed to affect absenteeism included differences in gender, departments/units, periods of the year, skill-levels and professions (chemists, technologists and accountants). The data were collected throughout a calendar year, using a biometric system infrastructure incorporating fingerprint capturing device, IP camera, database server and software (Bio Star Version 1.62) [25] . The absenteeism ratio based on hours, Abh, was observed to be the most appropriate parameter [25] . The lowest values of Abh (at 0.82% annual average) were observed in the business development department (BDD), with highest in PQSD at 26.91%. Female employees show higher Abh (at 17.54%) and lower Abd (at 20.36%) than male employees (at 12.93% and 20.36%, respectively), while accountants show lowest absenteeism (at −4.94%) compared to other professions (12.58% and 36.58% for chemists and technologists, respectively). Employees in professional level had highest absence rate (24.0%) compared to skilled (13.6%), semi-skilled (12.7%) and unskilled employees (9.5%). Most working hours were lost during September-December compared to the rest of the year. The results reveal higher employee absenteeism in the FSL affecting its overall performance as lost productivity [26] [27] [28] .

1.2.4. Employee Longevity and Academic Development

A detailed analysis of academic development index and longevity among laboratory employees was conducted aimed at improving organizational performance [29] - [35] . Data were collected from human resource database involving 171 (88%) employees out of 195. New mathematical formulations were developed for academic development index (Ad), simple longevity (Ls) and complex longevity (Lc). The values of Ad, Ls and Lc were compared for different units and departments including zonal laboratories between Y2014 and Y2016. Both total and average values of Ls, Lc and Ad indicated an imbalance in the distribution of staff in different laboratories, necessitating re-allocation to improve performance. The employment trend analysis indicated that the work force has been diversified from Y2004 to Y2016 leading to improved management of finance, procurement and human resource in the laboratory. As a result of a training program, the percent of staff with MSc has been increasing from about 3.5% in Y2004 to 9% in Y2015. Results show that a balanced staff distribution based on Lc and Ad is inevitable for improved performance. It was concluded that the new indices (Ad and Lc) are important tools towards development of the workforce and competitiveness of any laboratory as they lead to human performance improvement (HPI) [36] [37] .

1.2.5. Turnaround Time for Supply Chain Management Processes

The Supply Cycle Time (SCT) denoted as Tsc, depends on all factors that affect the turnaround times across its key components (the user, supplier, tender board, the procurement management unit performance). Baseline study revealed wide variations in Tsc, giving a mean of 105.6 days, which is extended. Reduction in Tsc must involve the FSL management and all key players in the SCM processes. However, the reduction of SCT by elimination of wastes in the processes is difficult as most of the SCM steps in between are pre-requisite in the said process and the steps are mandatory. Thus, step by step reduction in the Tsc is required. Lack of knowledge on procurement processes by staff in the user departments is another challenge to the FSL competitiveness. The Tsc is also extended due to the fact that most of the laboratory suppliers involve a relationship with third party vendors, which implies a complex relationship with the FSL.

2. Literature Review

2.1. Impact of Process Variables on FSL Competitiveness

The pillars of the FSL competitiveness include processes and organizational design. All these areas have been studied in details, before developing the CIF. Turnaround time analysis was accomplished by identifying action points to be assessed [9] [38] [39] , followed by detailed data collection. Moreover, the backlogged case-files, Ncb, were also repeatedly captured at different action points by determining the number of case-files received and reported [5] .

The laboratory turnaround time can also be defined differently according to the test type or analysis requested. The “total testing cycle” describes TAT as a syndicate of eight stages: collection, identification, transport, preparation, analysis, reporting, interpretation, and action [40] .

Supply chain management (SCM) is an integrative philosophy to manage the total flow of a distribution channel from supplier to the ultimate user [41] [42] . In this study, SCM analysis comprised of: determination of the TAT components in SCM; determination of procurement performance measurement system; interaction between the user, procurement management unit (PMU), accounts and supplier, and determination of the key metrics for supply chain management (financial and other metrics).

Organizational design analysis included case-file flow steps, supply chain management and human resources, and the actual human resource management (HRM). HRM involves forecasting and placement, staff experience and longevity, academic and professional development, staff absenteeism, staff responsibilities and interactions [25] [43] [44] .

2.2. Resource-Based Competitiveness

Researchers have advanced various methods for improving performance of laboratories including competitiveness, for example, a resource-based method [45] [46] . The term resource is meant anything which could be thought of as strength of a laboratory as an organization. According to this broad definition, resources can be tangible or intangible. In this case, organizations perform poorly because either they possess resources that are not in demand, own resources that are not scarce or do not own such resources [46] [47] . Improving performance of a laboratory requires understanding the core processes and factors hindering these processes. Intervention under this method would comprise of searching for resources that are in demand, scarce and appropriated by the organization, such as working areas, machinery, skilled and well developed staff, motivated staff, etc. Improving performance should adopt an industry-based method, which relies on the principles that laboratory success is based on its ability to harness opportunities and tame threats that exist in the business environment [48] [49] .

2.3. Effect of Extended Turnaround Time in Supply Chain Management on FSL Competitiveness

Supply chain management (SCM), is among the factors affecting FSL competitiveness. In this study, supplier-laboratory interactions have been assessed based on Tsc and financial metrics, etc. In FSL, the role and importance of the supply chain is mainly understood as evidence supply chain or the storage of evidence at the FSL. In this study, however, SCM focuses on material and services flow from suppliers. One of the methods which can be used to assess the key performance of supply chain management in the laboratory setting is consideration of issues affecting supply chain [50] . However, there is a need of having supply chain operators responsible for managing inventory flow to ensure that the goods arrive at the right place at exactly the right time, that is, the procurement management unit (PMU).

Supply chain performance measures (SCPM) serve as indicators of how well the supply chain system is functioning. Measuring SCP can facilitate a greater understanding of the supply chain and allow improving its overall performance [51] [52] . Different perspectives of SCPM are cost and non-cost perspective, strategic, tactical or operational focus [53] business process perspective and financial perspective [54] . In this study, the focus was on the challenges especially the turnaround time at every stage of product supply consideration and hence the total turnaround time, Tsc. The focus of SCM was the availability of services, consumables, reagents, chemicals, instruments or equipment for all laboratory settings.

2.4. Models for Improving Organizational Competitiveness

Competitiveness is a multidimensional concept, observed from different levels: national and organizational or firm level. Competitiveness means involvement in a business opposition for markets, in this study used to describe economic strength of entity laboratory with respect to its competitors [55] . Laboratory or firm-level competitiveness is defined as the capacity of the laboratory to design, produce and or sell its products or services superior to those offered by competitors, considering the price and non-price qualities.

Researchers suggest different framework designs for competitiveness. While others suggest a framework with three folds: performance, potential, and the management processes, others suggest a framework that involves a combination of assets and processes, where assets are either inherited (natural resources) or created (infrastructure) and processes transform assets to achieve economic gains from sales to customers [56] . Other authors present an approach which emphasizes the role of factors internal to the laboratories such as strategy, structures, competencies, capabilities to innovate, and other tangible and intangible resources for their competitive success [57] [58] . In order to provide customers with a greater value of satisfaction than their respective competitors, laboratories must be operationally efficient, cost effective, and quality conscious [59] .

Competitiveness improvement process seeks to identify the important factors and performance of core processes including the human resource processes, operations management processes (that is, laboratory processes based on case-file management and supply chain management) and planning or strategic management processes. Balancing the core processes will enhance the ability of laboratory to compete more effectively. Researchers view sources of competitiveness as those assets within the laboratory organization that provide advantage which can be tangible or intangible [60] .

Business design for FSL, therefore, has two principal requirements: sustaining casework productivities in a timely and efficient manner, whilst adhering to quality standards and the timelines of the investigatory and judicial processes. The design involves also developing and executing major programs of infrastructure investment and process re-engineering. Competitiveness is the ability of a laboratory or country to offer services and products that meet the quality standards of the local and global markets at prices that are competitive and provide adequate returns on resources employed [46] [61] . Competitiveness of a laboratory is measured in terms of quality of service, level of productivity, quality of human resource, price, and ability to innovate [31] [32] [35] [62] [63] .

Though several performance improvement methods have been proposed by scholars, yet they possess inherent deficiencies. Most literature discusses performance factors in singular. Therefore, in this study, competitiveness is discussed as multidirectional and multifactor concept observed at laboratory or firm-level. The multi-factors considered include the strategies of reducing backlogs, turnaround time and fewer customer complaints. The framework developed covers also multidimensional aspects of organizations namely, organizational processes, design, culture and politics [64] . The need to consider the environment is also taken into account in particular the stakeholder demand of services, and challenges in the laboratory business environment [48] .

3. Methodology

3.1. Utilizing the Cyclic Nature of the FSL Processes

(CIF) applies repetitive business processes such as the case flow management (CFM) assessed thoroughly in this research. In the FSL model setup, each case-file passes through several action points and complete processing is achieved before passing to another point. Whenever any action is completed time taken was noted while, if the case files are not completed in seven days, the case file is regarded as back logged. When another request for analysis of samples arrive, the same process is repeated at varying performance, measured using TAT, case-file backlogs (Bg), coupled with assigning staff of different traits (Ad, Lc and Ab), leading to a dynamic cyclic process of different characteristics. Figure 2 shows the decision diagram for conducting CIF analysis by observing designated events at different action points. Table 1 summarizes the parameters or cause factors assessed after capturing data in this study.

In forensic science laboratory, the repeating business takes place within the organization design or in the processes taking place within the laboratories. All the six parameters, or cause factors for FSL competiveness can be tracked in a repeating mode using the case-files as a unit of measure for laboratory issues (Bg, TAT), purchase order processing (Tsc) and absence/presence of staff with different traits (Ad, Lc) based on assignment case files (number of case files per analyst per year) and biometric database on daily basis (Ab). However, intervals among action points differ from one case-file to another which was measured leading to wide data volume for TAT and Bg. The processing time was also different for each purchase order, leading to data on Tsc.

3.2. Capturing Variations in the Total Turnaround Time and Backlogs during Case-File Management

Variations were identified in the turnaround time (TAT) for sample analysis.

Figure 2. Repeating business process map for case-file management in the FSL.

Table 1. Cyclic nature of the FSL processes and methods adopted for studying variations in the FSL processes.

The identified six components of the total turnaround time (TTAT) were also identified, which in turn vary from one case-file to another [14] . Each time interval between action points was determined as the difference between receiving and completion of processing time in the same action points. The initial and final times were recorded in dates giving TAT values in days, as shown in Figure 3. For simplicity, during TAT analysis, some of the time intervals were combined to give one delay reducing the number of time intervals or action points from 20 to 6. Meanwhile, some actions could proceed in parallel (where the reference date remains the same).

Based in Figure 3, the number of backlogged case-files was determined for each laboratory discipline, by comparing case-files in and case-files out, in a specified time interval, say 7 days [5] [14] .

3.3. Capturing Variations in the SCM Performance Measures

Turnaround time variations were also captured in the supply chain management. The supply chain cycle time, denoted as Tsc which measures the total time required to complete the order. The methodology used to establish the Tsc is complex due to wide involvement of staff and stakeholders, as well as large number of steps or action points. Repeating cycles in the form of orders were assessed and characterized as purchase orders were initiated and processed. For simplicity, the complex interactions among different SCM parameters were grouped together and the time between the order request and final payments were recorded. For further investigation on the effect of external environment on FSL competitiveness, the analysis was conducted separately for cycle times covering internal and external operations on purchase orders. Given the total

Figure 3. Capturing the repetitions and differences in TAT and backlogs for case-files at each work station.

number of orders in the period studied, Nto, all the order processes falls in the cyclic nature and repetition, which fits well into the development of the CIF.

The supply cycle time, Tsc, including payments acknowledgement, was determined as difference between date payments are made and acknowledged, Tpa and the date purchase order is requested by the user department, Tos. Table 2 summarizes the time variations by years studied and purchase order sampling details for determination of Tsc. Each purchase order processing undergoes the same cycle, based on which, variations in the cycle times were captured.

3.4. Variations in Staff Absenteeism

Measurements of absenteeism ratio, Ab, started with collecting data for individual employee on daily basis using the biometric system, from which, the ratio was expressed in terms of hours or days absent. For 192 staff logged into the system, this is a complex data set to manage [25] . Thus, the data was grouped into three time intervals (4 months), departments, units, gender, professions and skill levels to characterize and compare the average values. The determination of Ab is characterized by long time interval (3 months in this case), data screening to eliminate staff with special absence like study leave, maternity leave or sick leave, wrong data entry and errors, which reduces the sample size. The mathematical formulations implemented for absenteeism analysis can be summarized using a flow chart as shown in Figure 4, which shows two different outcomes of absenteeism data analysis, that is, day-based and hour-based absenteeism (Abh and Abd, respectively) [25] .

3.5. Variations in the Staff Academic Development

Another variation within the laboratory was identified in the staff academic development, experience and longevity which originate from individual employee data. The cyclic nature on this case stems from the fact that during employment

Table 2. Sampling details for case files used for supply cycle time analysis.

Figure 4. Flow chart for determination of employee absenteeism ratios Abh and Abd (based on 192 total employees).

and working life, each individual staff is subjected to academic development and longevity, data of which was captured not only once but at different times (Y2014 and Y2016) for comparison [44] . Successful management of any laboratory requires a great sense of self-awareness, commitment or engagement and the presence of the staff in the processes where academic development index, Ad, and complex longevity, Lc, play a vital role in performance and hence, competitiveness of the whole FSL as an organization. The parameters used to assess staff development (academic and professional development) are summarized in Figure 5. These variations arise among employees and also change with time for individual employees, specific FSL units or departments (total complex longevity or academic development index), which were used to develop the CIF. Thus variations in employee trails were captured as time possess while individual employee data offers another variation analysis opportunity by comparing individual staff, laboratory discipline, or zonal setting. The sample size (number of employees in each period) used to study variations in the academic development and longevity is also summarized in Figure 5.

Figure 5. Determination of academic development coefficient, Ad, and complex longevity, Lc.

3.6. Methodology for Implementation of Pareto Analysis

Given the six cause factors measured and implemented in the CIF development process, each factor was assessed on its relationship with: a) challenges in the FSL business environment and b) applicability of the lean practices for improving FSL competitiveness. The business environment challenges studies were 8 while the lean practices for CIF were 5, the so called variants. Let Nv = number of variants, that is, number of challenges in the business environment or number of lean practices (Nv = 8 and 5 respectively), and Ncf = number of cause factors measured and assessed for CIF development, that is, Ncf = 6. Then, using a scoring system of Ns = 1, 2 or 3 for low, medium and high connection between the cause factors and the challenges or practices respectively, the total score, Stot, for a given variant, was established based on Equation (1):

S t o t = i = 1 N c f N s , i (1)

The total score values for each variant, were then used to establish the percentage frequency distribution, using Equation (2).

F d = S t o k , k k = 1 N v S t o t , k (2)

Finally, Pareto analysis was conducted by analyzing the Fd values.

4. Results and Discussion

4.1. Summary of Variations Captured in the Laboratory Processes

4.1.1. Variations in the Turnaround Time

Based on TAT analysis, the performance of FSL disciplines shows strong variations between Y2014 and Y2015 as presented in Figure 6. For forensic chemistry,

Figure 6. CDFs of laboratories analysis turnaround time data for different laboratory disciplines in Y2014 and Y2015.

the number of case-files completed within one day of submission increased from 2% in Y2014 to 45% in Y2015. For biology/DNA, on the other hand, an opposite scenario was observed, as the performance decreased leading to very few case files completed in a given time of 50 days from 50% to only 35% of case files. For forensic toxicology, improved performance was observed, for instance, at a given TAT2 of 50 days, 60% of case files were completed in Y2014 which increased to 85% in Y2015. Cases where performance dropped require intervention if the FSL is to remain at its competitive edge.

4.1.2. Variations in the Backlogged Case-Files

According to Figure 7, variations in the laboratory performance with time for each discipline are obvious. The laboratory backlog data was assessed for each calendar year, from Y2014 to year Y2016. Figure 7 shows the cumulative distribution for Bg data for 52 weeks in each year. By drawing a vertical line at Bg = 10, using the collected data in three consecutive years, it is evident for DNA laboratory that the backlogs increased between Y2014 and Y2015 and decreased between Y2015 and Y2016. For forensic toxicology, backlogs increased between Y2014 and Y2015 while in forensic chemistry, backlogs decreased. Thus, variations in cause factors have been captured using data collection tools applied to the cyclic nature of the processes, allowing for identification of root causes and taking action to improve and sustain.

4.2. Harnessing Variations in Cause Factors for Competitiveness Improvement

One of the first steps towards FSL competitiveness improvement was to establish where the FSL stands among other organizations, that is, bench marking. The six

Figure 7. Variations in the weekly backlogs for three consecutive years.

parameters or cause factors affecting competitiveness were studied in details and quantified between Y2014 and Y2016 so that improvements and sustainability can be measured in the next few years or later. This study is thus used as a definitive guide on what needs to be improved. Table 3 gives what is needed to improve based on the pre-determined performance factors and how to approach the improvements. In details, gives the key steps applicable to each cause factor starting from relevance of each factor to FSL, stakeholders and baseline or current status are given. Means of improving and sustaining competitiveness via these cause factors are also presented in Table 3. Finally, future plans for sustaining competitiveness are also summarized.

Not shown in Table 1 are the responsible directors, managers or departments and units towards sustainability of the competitiveness improvement methods identified which can be done internally, as it depends on the organizational structure of the laboratory. With six cause factors identified, improvement of competitiveness is not a minor task since requirements span into many directions and above all, time consuming and costs money. Maintaining the competiveness is a difficult task because of many factors that influence the FSL and the market or clients, some of which are not controllable by FSL management (e.g. components of SCM played by suppliers) necessitating efforts in backstopping. Factors like technological advancement or lack of specialized equipment could put the laboratory out of competitive advantage. If improvements are made across the six cause factors, the resulting competiveness improvement will be achieved through reduced backlogged case-files, reduced TAT and improved QMS.

Table 3. The relevance of cause factors of the FSL performance towards competitive improvement.

4.3. Competitiveness Improvement by Managing the Dimensions

4.3.1. Dimensions of the FSL Competitiveness

The competitiveness improvement framework involves individual staff, product (laboratory reports) and FSL services (receiving/processing exhibits, expert witness and training for sampling officers). Single measures of competitiveness (e.g. finance, SCM, etc.), do not capture all the elements of the research issue, it was necessary to examine performance, potential and management processes (shown in Figure 8), in order to evaluate critically the changes or level of competiveness and interrelationship. The Venn diagram in Figure 8 shows the interrelationship between the competitiveness dimensions based on the cause factors measured and analyzed in this study.

4.3.2. Competitiveness Improvement by Managing Performance in the Laboratory

Under this component, the study measured the status of Ad, Lc and Ab which are related to staff capability or tools to enable them push the organization towards competitive advantage, for the FSL to improve its performance. Managing the performance in FSL should be an ongoing communication process conducted which is carried out between the supervisors and the employees throughout the year. A system of managing the performance comprises of activities such as development of job descriptions within the different FSL disciplines and employee performance plans which includes the key result areas (KRAs) and performance indicators with respect to the cause factors: Ad, TAT, Tsc and Bg. Placement and staffing of the appropriate staff and providing continuous training and response during the period of delivery of performance is essential in performance management.

A performance management process sets the stage for fulfilling distinctions by supporting the FSL staff undertaking with the FSL mission and. The CIF is designed with the objective of improving both individual and FSL performance by identifying performance requirements with respect to the cause factors, providing regular feedback and assisting the FSL’s employees in their career development. It is also aimed at building a high performance culture for both individuals and the FSL management team so that they jointly take the responsibility of

Figure 8. Interrelationship between the dimensions of FSLs competitiveness.

improving the business processes on a continuous basis and at the same time raises the competence bar by upgrading their own skills within a leadership framework.

The sole purpose of a performance management system for a given laboratory is to assess and ensure that the employees are carrying out their duties in an effective and satisfactory manner. The performance of the employees can be improved by inspiring employee empowerment, incentive and operation of an effective reward mechanism. In addition, identifying the obstacles towards effective performance and resolving those obstacles through continuous monitoring, training and development involvements will create a basis for several administrative decisions, strategic planning, business plans, succession and competence plans, academic development plans, etc. Also, encouraging personal growth and advancement in the career of the employees by helping them in acquiring the desired knowledge and skills may increase the staff performance and hence competitiveness of the FSL [44] .

These factors identified and shown in Figure 8 and Table 3 and Table 4 demand a lot from the human resource team, all of which are based on performance management issues. Thus, performance management is much of a comprehensive and a complex function, as it incorporates activities such as mutual goal setting, continuous progress assessment and regular communication, response and training for improved performance and implementation of employee development plans. In addition, FSL employees should continually be seeking ways to improve their own performance, to take ownership for their work, and reinforce team working, thereby improving worker motivation.

4.3.3. Improving Competitiveness via Management of Laboratory Processes

Another aspect of CIF portrayed in Figure 9 is process management, a concept that integrates quality, performance and excellence during accomplishing the tasks in the laboratory that connects the organization with clients (processes). The process parameters identified in this study include TAT, Bg, and Tsc. These parameters should be managed while focusing at CIF as they connect with the outside customers or stakeholders.

Process management consist of process design or engineering (which is the development of new processes), process definition (narrative of the current processes), process documentation, analysis and control and process improvement. Process design and definition include describing the essential procedures to accomplish the tasks followed by describing the process using flowcharts, process maps or checklists. This will enable the process pertinent data to be collected, analyzed and improved. There are many process analysis tools, including cause-and-effect diagrams, statistical process control, and trend analyses. In this study, simple statistical analysis using PDFs and CDFs, Pareto charts were able to indicate areas requiring improvements (Tables 1-3). Process improvement may result from improvements based on many, small changes rather than few

Figure 9. Pareto analysis for ranking the business environment challenges for competitiveness improvement in the FSL.

Table 4. Process management remarks with respect to cause factors.

radical changes. Ideas for such changes come from the workers themselves based on the talents of the existing workforce and therefore easier to implement. Also, such changes involved in process management should not require major capital investment, consultants or expensive equipment.

For the purpose of CIF development, detailed review and conceptualization of laboratory processes were done using conceptual frameworks [5] [14] [25] . Given that a process is a series of connected steps or actions with a beginning and an end that can be replicated, conceptual models for TAT, Tsc and Bg, were established [5] [14] . The FSL was viewed as a set or hierarchy of laboratory processes that yield analytical reports and services of value to the criminal justice system and investigative science, as well as a set of functions such as chemical or genetic profiling, expert witnessing, accounting, procuring of supplies or services, training and capacity building. Table 4 summarizes the process remarks with respect to the cause factors in relation to arrangement of processes.

For the laboratory to experience the highest levels of success and hence competitiveness, external and internal customers must be satisfied. Each laboratory staff (chemists, accountants and technologists) have the duty to understand their roles as suppliers to internal and external customers. Principally, customers want to be their suppliers' first priority. They deserve perfect analytical reports, which delivered on or ahead of schedule (client’s charter). They expect suppliers to be in the improvement mode of operation so that the criminal justice system and the investigative science field are assured of a competitive third opinion expert advice to bring justice.

Process management has potential for improvement. The FSL management should focus on current issues to avoid performing analysis using old methods which are of no use to the criminal justice system. Furthermore, focus may be on quality, whereas reduced turnaround time is crucial. In addition, determining the supplier performance using rating system based on quality, capabilities, conformance to requirements is an important role in process performance measuring.

4.4. The Role of Policies, Procedures and Plans on Competitiveness Improvement

The third component of CIF presented in Figure 3 is the role of policies, procedures, programs and plans (strategic plans, staff training program, improvement programs, expenditure framework, etc.). The competitiveness and service viability of forensic science services (FSS) industry as well as its disciplines can potentially be enhanced by planning strategically for future. Laboratory strategic planning, especially in the selected priority disciplines can help set the stage for appropriate responses to the many dynamic changes and driving forces that impact the FSS industry. The FSS strategic planning must take into consideration the laboratory complexities, necessitating comprehensive perception.

FSS faces continuous challenges. It is therefore required to have a constant and enduring strategic planning in a dynamic manner so as to encounter challenges in rapidly changing technologies within the FSS industry and dynamic personnel skills requirement. Planning strategically requires to be focused over the future for a period of years. The planning process must be effective in a continuous manner capturing FSL conditions, external environment, challenges and changing priorities. Regular updates are essential. Areas of emphasis for the FSS strategic planning will change over a period of time as the laboratory service industry priorities undergo transformation.

4.5. Identification and Elimination of Wastes in the FSL Processes

Anything that doesn’t increase value in the laboratory processes and in the perception of the customers must be considered as waste and every effort should be made by the management to eliminate that waste. By understanding the different types of waste within the laboratory it is possible to eliminate or reduce impact of such steps to the performance and competitiveness. In this study, such wastes were reached at after detailed analysis of the cause factors, as summarized in Table 5.

4.6. Effect of Laboratory Business Environment on Measured Cause Factors

Services offered that differentiate FSL from other organizations are those that are associated with criminal justice. While the rest of laboratory services are subjected to competition. Commercial or private laboratories, research cum training laboratories, other government laboratories, are likely to give stiff competition to the FSL. Any laboratory is regarded as competitive if its services consider priority to regular customers, priority services with additional charges for faster services, discount on the cost, and continuous improved/innovative quality services. Also, quick and short delivery of services at reduced waiting time through a provision of mistake-proof or error-free services is a key to competitiveness. The CIF parameters shown in Table 6 were identified through data collection and application of the AHP methodology in ranking the factors. Table 6 shows the importance of the cause factors towards competitiveness and category of indicators to be utilized. The categories denoted as A, B and C have the following extended description: A—Outcome indicators that capture the final objectives of policy; B—Fundamental factor of competitiveness that structurally drives outcomes and which are core levels for policy intervention that can have sustainable impact; and, C—Control indicators that capture potential imbalance that have the potential to create high short term costs even if they don’t drive outcomes in the long run.

During development of the CIF, it was important to characterize the cause factors in relation to whether improvements can lead to increased customer awareness and satisfaction, increased number and strength of customer specifications or increased purchase power of customers. Moreover, the cause factors were assessed and rated in relation to coping with fast changing technology, large number of competitors, newer business models and practices, and also on the need for improved business infrastructure. Newer business models in the public laboratory like FSL are difficult to implement, giving chance to competitors in implementing such models like private sector and research institutions, laboratories. The last rating was focused on whether the cause factors are affected by frequently changing government policies or increased cost of manpower in order to improve, as shown in Table 7.

Using the total score determined from summation of the rating values for each challenge found in the business environment, as presented in Table 7, it

Table 5. Wastes identified in FSL processes and possible means of elimination.

Table 6. Measured cause factors identified to affect FSL competitiveness.

Table 7. Rating of the cause factors based on applicability of competitiveness challenges in the FSL business environment (√√√ = high, √√ = medium, √ = low).

was possible to arrange the challenges in descending order, and apply Pareto analysis, as summarized in Figure 9. Based in Figure 9, there are five challenges in the business environment that the laboratory needs to address first in order to improve its competitiveness by 80% while utilizing 20% of the rather limited resources. These challenges are: increased purchase power of customers; frequently changing government policies; increased cost of manpower; fast changing technology; large number of competitors; and, increased customer awareness, in that order of importance. The last three challenges, contribute only 20% of the problems facing the competitiveness of the laboratory.

Furthermore, Table 8 shows the means of which the above nine challenges in the business environment affect FSL via the six cause factors identified and measured in this study. The business environment challenges are also arranged in the same order as presented in the Pareto chart (Figure 9).

4.7. Application of D-MAIC Methodology in Competitiveness Improvement

In this study, D-MAIC methodology was selected as a tool to provide a roadmap that can be followed for competitiveness improvement for the laboratory. The term D-MAIC comes from the five principle steps in this process which include Define, Measure, Analyze, Improve, and Control as shown in Figure 10. Based in Figure 10, the effects and impacts of the cause factors on FSL competitiveness were established in specific details, to increase the probability of designing or remodeling for a better improvement. After identifying the cause factors, measurements and quantification of the variations were made to determine the current status of the cause factors as a study parameter in the specific discipline of the laboratory. Analyze implies quantification of the current status, followed by analysis and presentation of the data collected. In this study, data collected on TAT, Ab, Bg, Ad, Lc, and Tsc were analyzed and presented in understandable

Table 8. Summary of recommendations for the business environment challenges for competitiveness improvement in the FSL based on cause factors.

Figure 10. Simple flow chart for competitiveness improvement for FSL based on D-MAIC methodology.

format, [5] [14] [25] [44] showing the criticality of current situation and action required. At this point, it is important to establish a need to redesign or re-model the existing conceptual model of the FSL system or there is a specific cause factor that has to be corrected. Analysis was followed by remodeling or optimization, before improvement and control. In this case control means maintaining the improved system to prevent the system from going back to the initial poor state (sustainability). Table 9 shows the competitiveness improvement framework developed using the detailed D-MAIC methodology for the FSL.

Based in Table 9, the competitiveness improvement framework has been presented in five key steps of D-MAIC but also using 15-step processes with highly detailed process analysis for each step in relation to the cause factors established. The possible measures for improving competitiveness can then be introduced or an optimum can be used for the existing situation suggested as per concepts in Table 9. Also, trial statistics can be designed for the purpose of prioritization as which cause factor gives the highest improvements towards competiveness depending on the client’s demands. An example of such analysis is AHP application, used in this study to rank the factors, keeping in mind that the cause factors are interdependent. Subsequently, as stated above implementation of the improvement measures requires controls to be placed so that they can confirm sustainability and prevent recurrence. The control measurements for improvement

Table 9. FSL Competitiveness improvement framework based on detailed D-MAIC methodology.

should be scheduled with specific dates, e.g., daily, monthly, yearly, etc. Also, the improvement measures and other related processes have to be documented. Figure 11 presents a flow chart for competitiveness improvement based on a detailed D-MAIC methodology using 15 steps presented in Table 9.

4.8. Lean Practices for Competitiveness Improvement

A firm’s competitiveness advantage grows fundamentally out of the value it can provide to its clients. For instance, TAT, and Tsc are the major cause factors that affect strongly or directly the laboratory-client relationship, which can be reduced to improve the competitive edge. The samples and case file processing and management is a unique product which should be managed properly in a way, not offered by any competitor which creates a strong relationship with clients.

Lean process is about FSL being effective and efficient. It begins from the point of understanding the customer requirements, standards and prerequisites and performs the best way to provide the analytical reports and expert opinion. Table 10 is a template for continuously measuring the potential lean practices of FSL, where six lean processes related to the cause factors affecting FSL competitiveness have been analyzed. Where there was no relationship between the cause factors and the lean practices no score was inserted, equivalent to zero score.

The total scores presented in Table 10 were further analyzed using Pareto principle, as shown in Figure 12, based on which, the higher the score the more effective the practice in bringing positive change to the complex and dynamic laboratory business environment. Using Pareto principle, there are three lean practices that can be applied in order to improve competitiveness of the FSL by 80%, while utilizing 20% of the resources, as shown in Figure 12. These lean practices are: continuous improvement of services, customer satisfaction and record keeping. Thus, to fasten competitiveness improvement for the laboratory,

Table 10. Applicability of potential of lean practices for improving competitiveness of the FSLs for the measured factors affecting competitiveness (rating: √√√ = high, √√ = medium, √ = low).

Figure 11. Detailed flow chart for competitiveness improvement in the FSL based on detailed D-MAIC methodology.

Figure 12. Pareto analysis of the lean practices for improving FSL competitiveness.

it is important to understand how the competitors benefit from the bottlenecks or problems facing the organization and also to find out how the external competitive environment affects the measured factors.

4.9. Improving Operational Competitiveness in the Laboratory

In relation to the CI process and the cause factors studies, it was possible to establish from literature, the methods for improving operational competitiveness in the laboratory, that is economic added value, total shareholder return, value curve, capacity maturity model, and assets processes performance framework. Table 11 defines each method in relation to the cause factors established in this study. Thus, directors and laboratory managers should be aware of the operational competitiveness requirements being placed on them at the conceptual level, whereby, attempts to reorient the way in which they operate shall be observed significantly and that a continuous improvement culture should be slowly accommodated within the FSL such that the gap between Government policy on the one hand and implementation on the other is narrowed.

After observing the cause factors that affect the FSL competitiveness, it is important to effect methods that can assist in improving the competitiveness. Table 12 shows how these methods, forces and strategies to achieve better performance can be integrated to improve competitiveness for each of cause factors in accordance with the four competitiveness paradigms. The features of operational competiveness are action-oriented in design and focus on critical factors that are impacting the FSL competitiveness. There is a need to improve operational competitiveness of the laboratory. The abbreviations used for different methods for improvement of operational competitiveness can be found in Table 11, which fall on financial analysis category.

Based on Table 12, the methods for improving operational competitiveness play an important role in ensuring that the laboratory makes an important progress in changing the way in which it operates and hence become more competitive. It should be noted that operational competitiveness improvement is strongly related to EVA, TSR, VC, CMM and APPF. Additional methods like Balanced Scorecard (BSC) and Integrated Value Management (IVM), respectively, are also suggested for CIF.

4.10. Presentation of the Complete Competitiveness Improvement Framework for Laboratories

Finally, methods for improving competitiveness in FSL were outlined by combining the competitiveness paradigms with the methods to improve operational competitiveness. At the end, the complete Competitiveness Improvement Framework in the FSL was presented using a flow chart presented in three sections shown in Figures 13(a)-(c). The CIF for FSL is developed using the cyclic nature of the FSL processes. Furthermore, variations in the backlogs, components of the total turnaround time, SCM performance measures, staff absenteeism and in the staff academic and professional development were utilized from baseline data collected, as summarized in Figure 13(a).

The flow chart for a complete competitiveness improvement framework consists of five layers or phases: first the baseline study, data analysis and presentation.

Table 11. Methods and financial measures for improving operational competitiveness.

Table 12. Competitiveness paradigm, forces, strategies and methods to improving competitiveness for each cause factors.

The second layer involves identification and elimination of wastes, followed by a third layer, that is, use of D-MAIC methodology. Layer four comprises of assessing the applicable challenges in the laboratory business environment in relation to cause factors and ranking by Pareto analysis, also shown in Figure 13(a).

Phase five involves grouping the cause factors according to measures for improving competiveness considering the CI dimensions (process, performance, and planning dimensions) and application of operational improvement methods (economic value, total shareholder, value curve, capability maturity model, and assets processes performance framework) to the cause factors followed by ranking of the methods using Pareto analysis as shown in Figure 13(b) and Figure 13(c).

The CIF developed provides a common reference for a diverse set of FSLs, to assist in organizing the competitiveness improvement process, re-framing the


Figure 13. (a) Initial CIF development steps from baseline data collection to ranking of cause factors; (b) Prioritization of business environment challenges affecting the laboratory competitiveness using Pareto analysis; (c) Application of lean practices and economic measures for improving laboratory competitiveness.

perspectives and design analytical FSS strategies to reduce TAT, Tsc and Bg. It also establishes a tool that will make complex FSL systems as simple as they need to be by structuring and prioritizing the workflow meanwhile reducing absenteeism. The CIF clarifies and creates focus thinking about complex relationships within FSS, thereby supporting communication across FSL disciplines, knowledge systems, and between forensic science and policy to increase staff longevity, professional and academic development.

5. Conclusions

The development of CIF based on captured variations in the laboratory processes including fluctuations in TAT between different case files, between different action points and different laboratory disciplines enabled a deep understanding of process variations, via statistical analysis (CDFs). While it is difficult to trace performance metrics in the laboratory due to difficulties in gathering data, this study shows that it is possible to capture data given well designed data collection tools. Variations in the backlogged case files with time revealed similar CDF shapes between different laboratory disciplines, but different nature of factors affecting case files inflow and reported or processed case files on weekly basis. The results show that the extent of backlogs is alarming necessitating action. The cause factors developed in this study were assessed for relevance to stakeholders, current status, means of improvements, low to sustain and future plans for sustainability.

The case factors studied were observed to be complex and interrelated based on dimensions of competitiveness (planning, process, and performance). A Venn diagram was used to represent the interrelationships between cause factors, followed by the need to establish the indicators of competitiveness, application of AHP methodology, improvement methods and sustainability analysis. The study reveals that competitiveness improvement requires managing the dimensions of competitiveness (performance, process, and planning). The study shows the process management areas such as customers of the process, relationship between customers, between quantity, schedule and cost, identifying process owners, performing improvements, and the role of measuring the current status. CIF development includes identification followed by elimination of wastes (such as waiting, overproduction, defects, under-utilized human resources, excess processing, transportation distances and inventory). The measured parameters were also assessed for importance and their effects to the FSL competitiveness, using Pareto analysis, for ranking business environment challenges (after detailed analysis) and ranking lean practices for improving FSL competitiveness.

The CIF development necessitated application of D-MAIC methodology based on simple 5-step and intensive 15-step methodology while providing relationship between each D-MAIC step with the cause factors and concepts used for conducting analysis of each step. The need for improving operational competitiveness involved linking the requirements with the cause factors. Some of the requirements utilized and linked to the cause factors include analysis of economic added value, total shareholder return, value curve, capability maturity model, and assets processes performance framework. This step involved also linking the categories of competitiveness paradigm with cause factors, analyzing forces that determine competitiveness, strategies to achieve better performance, and methods to improve operational competitiveness in relation to cause factors.

Finally, based on the developed methodology, the complete competitiveness improvement framework was presented in the form of a flowchart, showing the necessary steps with inputs to each step. The flow chart starts with data collection to establish the current situation for all six cause factors and ends with the final steps presenting the measures for improving the competitiveness.


The authors are grateful to the GCLA Management for financial support which enabled completion of this study.

Conflicts of Interest

The authors declare no conflicts of interest regarding the publication of this paper.


[1] Warnack, M. (2003) Continual Improvement Programs and ISO 9001:2000. Quality Progress, 36, 42-49.
[2] Feist, A., Ashe, J., Lawrence, J., McPhee, D. and Wilson, R. (2007) Investigating and Detecting Recorded Offences of Rape. Home Office, London.
[3] Delisi, M., Hochstetler, A., Scherer, A.M., Purhmann, A. and Mark, B.T. (2008) The Stark Weather Syndrome: Exploring Criminal History Antecedents of Homicidal Crime Sprees. Criminal Justice Studies, 21, 37-47.
[4] Durose, M.R. (2008) Census of Publicly Funded Crime Forensic Crime Laboratories 2005. Bureau of Justice Statistics Bulletin.
[5] Omari, G.C., Manyele, S.V. and Mwaluko, G. (2017) Analysis of Stress Backlogs during Case-File Processing in Forensic Science Laboratory. Engineering, 9, 1060-1096.
[6] Coble, M.D. and Butler, J.M. (2005) Characterization of New MiniSTR Loci to Aid Analysis of Degraded DNA. Journal of Forensic Science, 50, 43-53.
[7] CCLRTF (2009) California Crime Laboratory Review Task Force Report.
[8] Bashinski, J. (2010) DNA Laboratory Monthly Statistics. Office of the Attorney General, California Department of Justice, Sacramento.
[9] Hawkins, R.C. (2007) Laboratory Turnaround Time. Clinical Biochemist Reviews, 28, 179-194.
[10] Chung, H.-J., Lee, W., Chun, S., Park, H.-I. and Min, W.-K. (2009) Analysis of Turnaround Time by Subdividing Three Phases for Outpatient Chemistry Specimens. Annals of Clinical and Laboratory Sciences, 39, 144-149.
[11] Hilborne, L.H., Oye, R.K., McArdle, J.E., Repinski, J.A. and Rodgerson, D.O. (1989) Evaluation of Stat and Routine Turnaround Times as a Component of Laboratory Quality. American Journal of Clinical Pathology, 91, 331-335.
[12] Howanitz, P.J., Cembrowski, G.S. and Steindel, S.J. (1993) Physician Goals and Laboratory Test Turnaround Times. Archives of Pathology & Laboratory Medicine, 117, 22-28.
[13] Steindel, S.J., Jones, B.A. and Howanitz, P.J. (1996) Timelineness of Automated Routine Laboratory Tests: A College of American Pathologists Q-Probes Study of 653 Institutions. Clinical Chimical Acta, 251, 25-40.
[14] Omari, G.C., Manyele, S.V. and Mwaluko, G. (2018) Analysis of Turnaround Time during Casefile and Sample Processing in Forensic Science Laboratory. Engineering, 10, 43-73.
[15] Steindel, S.J. (1995) Timeliness of Clinical Laboratory Tests, a Discussion Based on Five College of American Pathologist Q-Probe Studies. Archives of Pathology & Laboratory Medicine, 119, 952-961.
[16] Kenagy, J.W., Berwick, D.M. and Shone, M.F. (1999) Service Quality in Healthcare. Journal of the American Medical Association, 281, 661-665.
[17] Rasasingham, R. (2015) The Risk and Protective Factors of School Absenteeism. Open Journal of Psychiatry, 5, 195-203.
[18] Vanneste, Y.T.M., Mathijssen, J.J.P., Goor, L.A.M., van de Rots-de Vries, M.C. and Feron, F.J.M. (2015) Extensive Medical Absenteeism among Secondary School Students: An Observational Study on Their Health Condition from a Biopsychosocial Perspective. Open Journal of Preventive Medicine, 5, 111-121.
[19] Kanwal, N., Riaz, G., Riaz, M.S. and Safdar, S. (2017) Identify the Causes of Absenteeism in Nurses Mayo Hospital Lahore Pakistan. International Journaal of Social Sciecnce and Management, 4, 110-114.
[20] Goldberg, C.B. and Waldman, D. (2000) Modeling Employee Absenteeism: Testing Alternative Measures and Mediated Effects Based on Job Satisfaction. Journal of Organizational Behavior, 21, 665-676.<665::AID-JOB48>3.0.CO;2-P
[21] Chen, L.H. (2008) Job Satisfaction among Information System (IS) Personnel. Computers and Human Behavior, 24, 105-118.
[22] Nyathi, M. (2008) Working Conditions That Contribute to Absenteeism among Nurses in a Provincial Hospital in the Limpopo Province. Curationis, 31, 28-37.
[23] Pillay, R. (2009) Work Satisfaction of Professional Nurses in South Africa: A Comparative Analysis of the Public and Private Sectors. Human Resource for Health, 7, 7-15.
[24] Leszek, K., Zenon, M. and Michał, K. (2016) The Concept of Absenteeism Management System in a Company. The Małopolska School of Economics in Tarnów Research Study’s Collection, 32, 59-73.
[25] Omari, G.C., Manyele, S.V. and Mwaluko, G. (2019a) Analysis of Measured Employees’ Absenteeism in the Forensic Science Laboratory. Engineering, 11, 137-166.
[26] McHugh, M. (2001) Employee Absence: An Impediment to Organizational Health in Local Government. The International Journal of Public Sector Management, 14, 43-58.
[27] Onikoyi, I.A., Awolusi, O.D. and Ayodeji, B.M. (2015) Effect of Absenteeism on Corporate Performance: A Case Study of Cadbury Nigeria PLC, Ikeja, Lagos State, Nigeria. British Journal of Marketing Studies, 3, 58-71.
[28] Tiwari, U. (2014) Impact of Absenteeism and Labour Turnover on Organizational Performance at Iti, Nani Allahabad, India. Abhinav National Monthly Refereed Journal of Research in Commerce & Management, 34, 9-15.
[29] Iles, P.A., Mabey, C. and Robertson, I.T. (1990) HRM Practices and Employee Commitment: Possibilities, Pitfalls and Paradoxes. British Journal of Management, 1, 147-157.
[30] Green, F. (1993) The Determinants of Training of Male and Female Employees in Britain. Oxford Bulletin of Economics and Statistic, 55, 103-122.
[31] Mincer, J. (1997) The Production of Human Capital and the Life Cycle of Earnings: Variations on a Theme. Journal of Labor Economics, 15, 26-47.
[32] Nordhaug, O. (1998) Competencies Specificities in Organizations. International Studies of Management and Organisation, 28, 8-29.
[33] Robertson, M. and O’Malley-Hammersley, G. (2000) Knowledge Management Practices within a Knowledge-Intensive Firm: The Significance of the People Management Dimension. Journal of European Industrial Training, 24, 241-253.
[34] Garavan, T.N., Morely, M., Gunnigle, P. and Collins, E. (2001) Human Capital Accumulation: The Role of Human Resource Development. Journal of European Industrial Training, 25, 48-68.
[35] Hameed, A. and Waheed, A. (2011) Employee Development and Its Effect on Employee Performance: A Conceptual Framework. International Journal of Business and Social Science, 2, 224-229.
[36] Valles, A., Sanchez, J., Noriega, S. and Nuñez, B.G. (2009) Implementation of Six Sigma in a Manufacturing Process: A Case Study. International Journal of Industrial Engineering, 16, 171-181.
[37] Gijo, E.V., Scaria, J. and Antony, J. (2011) Application of Six Sigma Methodology to Reduce Defects of a Grinding Process. Quality and Reliability Engineering International, 27, 1221-1234.
[38] Truchaud, A., Le Neel, T., Brochard, H., Malvaux, S., Moyo, M. and Cazaubiel, M. (1997) New Tools for Laboratory Design and Management. Clinical Chemistry, 43, 1709-1715.
[39] Kilgore, M.L., Steindel, S.J. and Smith, J.A. (1998) Evaluating Stat Testing Options in in Academic Health Center: Therapeutic Turnaround Time and Staff Satisfaction. Clinical Chemistry, 44, 1597-1603.
[40] Kaur, V., Kamaljit, S., Minni, V. and Chopra, B. (2015) Monitoring of Turnaround time (TAT) in Biochemistry Laboratory of a Tertiary Care Hospital in Punjab. Journal of Dental and Medical Sciences, 14, 9-12.
[41] Cooper, C.M., Ellram, L.M., Gardner, J.T. and Hanks, A.M. (1993) Meshing Multiple Alliances. Journal of Business Logistics, 18, 67-89.
[42] Mentzer, J.T., DeWitt, W., Keebler, J.S., Nix, N.W., Smith, C.D. and Zacharia, Z.G. (2001) Defining Supply Chain Management. Journal of Business Logistics, 22, 1-25.
[43] Akhigbe, O.J. (2013) Human Resource Planning: A Key Factor in Ensuring the Effectiveness and Efficiency of Organization. Journal of Emerging Trends in Economics and Management Sciences, 4, 388-396.
[44] Omari, G.C., Manyele, S.V. and Mwaluko, G. (2019b) Analysis of Employee’s Academic Development and Longevity in Forensic Science Laboratory. Engineering, 11, 206-230.
[45] Wernerfelt, B. (1984) A Resource-Based View of the Firm. Strategic Management Journal, 5, 171-180.
[46] Collis, D.J. and Montgomery, C.A. (1995) Competing on Resources: Strategy in the 1990s. Harvard Business Review, 73, 118-128.
[47] Grant, R.M. (1991) The Resource-Based Approach to Strategy Analysis: Implications for Strategy Formulation. California Management Review, 33, 114-135.
[48] Porter, M.E. (1998) Competitive Strategy: Techniques for Analyzing Industries and Competitors. University of Illinois-Urbana, Historical Research Reference in Entrepreneurial Ship, Free Press, New York.
[49] Morgan, G. (1986) Images of Organization. Sage, Newbury Park.
[50] Beamon, B.M. (1998) Supply Chain Design and Analysis: Models and Methods. International Journal of Production Economics, 55, 281-294.
[51] Charan, P., Shankar, R. and Baisya, R.K. (2008) Analysis of Interactions among the Variables of Supply Chain Performance Measurement System Implementation. Business Process Management Journal, 14, 512-529.
[52] Taticchi, P., Tonelli, F. and Pasqualino, R. (2013) Performance Measurement of Sustainable Supply Chains: A Literature Review and a Research Agenda. International Journal of Productivity and Performance Management, 62, 782-804.
[53] Gunasekaran, A., Patel, A. and Mcgaughey, R.E. (2004) A Framework for Supply Chain Performance Measurement. International Journal of Production Economics, 87, 333-347.
[54] Bottani, E. and Montanari. R. (2010) Supply Chain Design and Cost Analysis Through Simulation. International Journal of Production Research, 48, 2859-2886.
[55] Murths, T.P. (1998) Country Capabilities and the Strategic State: How National Political Institutions Affect MNC Strategies. Strategic Management Journal, 15, 113-129.
[56] Buclkey, P.J. (1998) The Limits of Explanations: Testing the Internalization Theory. Journal of International Business Studies, 19, 181-194.
[57] Bartlett, C. and Ghoshal, S. (1991) Global Strategic Management: Impact on the New Frontiers of Strategy Research. Strategic Management Journal, 12, 5-16.
[58] Hamel, G. and Prahalad, C.K. (1989) Strategic Intent. Harvard Business Review, 67, 63-76
[59] Hammer, M. and Champy, J. (1993) Reengineering the Corporation: A Manifesto for Business Revolution. Scientific Research: An Academic Publisher, Harper Collins, New York.
[60] D’Cruz, J.R. and Rugman, A.M. (1992) New Impact for Canadian Competitiveness. Faculty of Management, University of Toronto, Toronto.
[61] Bakan, İ. and Doğan, İ.F. (2012) Competitiveness of the Industries Based on the Porter’s Diamond Model: An Empirical Study. International Journal of Research and Reviews in Applied Sciences, 11, 441-455.
[62] Bates, T. (1990) Entrepreneur Human Capital Inputs and Small Business Longevity. The Review of Economics and Statistics, 72, 551-559.
[63] Qaiser, A., Tayyba, N., Imran, K., Rafaqet, A. and Asim, Y. (2018) The Impact of Human Resource Management Practices on Innovative Ability of Employees Moderated by Organizational Culture. International Journal of Organizational Leadership, 7, 426-439.
[64] Flood, C.R. and Michael, C.J. (1993) Critical Systems Thinking. Sage Journals: Organization Studies, 14, 613.
[65] Grant, J.L. (2003) Foundations of Economic Value Added. John Wiley and Sons, Hoboken.
[66] Sabol, A. and Sverer, F. (2017) A Review of the Economic Value Added Literature and Application. UTMS Journal of Economics, University of Tourism and Management, Skopje, 8, 19-27.
[67] Herciu, M. and Lucian, B. (2016) Creating Value—From Corporate Governance to Total Shareholders Return. An Overview. Studies in Business and Economics, 11, 36-50.
[68] Hill, C.W.L. and Jones, G.R. (2010) Strategic Management Theory: An Integrated Approach, South-Western, USA.
[69] Kim, W.C. and Mauborgne, R. (1999) Creating New Market Space: A Systematic Approach to Value Innovation Can Help Companies Break Free from the Competitive Pack. Harvard Business Review, 83-93.
[70] Humphrey, W.S. (2002) Three Process Perspectives: Organizations, Teams, and People. Annals of Software Engineering, 4, 39-72.
[71] Amaratunga, D., Baldry, D. and Sarshar, M. (2002) Assessment of Facilities Management Performance—What Next? Facilities, 18, 66-75.
[72] McDougall, G., Kelly, J., Hinks, J. and Bititci, U. (2002) A Review of the Leading Performance Measurement Tools for Assessing Buildings. Journal of Facilities Management, 1, 142-153.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.