UV Photocatalytic Degradation of Commercial Naphthenic Acid Using TiO2-Zeolite Composites

Abstract

The presence of naphthenic acids in oil sand products and process streams is the cause of toxicity to aquatic life and corrosion. The removal of organic acids from tailings pond water reduces the negative impact on marine life. The ultra-violet (UV) photocatalytic reduction of commercial naphthenic acid in water using TiO2-zeolitecomposites showed a significant decrease in the concentration of naphthenic acid, accompanied by an increase in carbon dioxide formation; the presence of carbon dioxide signifies degradation of the naphthenic acids. Mixtures of the acid and photocatalyst kept in the dark did not show any concentration changes. The extent of naphthenic acid reduction by UV light was verified by the reduction in total acidity. The total acidity values of mixtures of the acid and TiO2-zeoliteexposed to UV decreased by 31% compared to mixtures kept in the dark. A reduction in total acidity may lead to a decrease in the toxicity of naphthenic acid contaminated water.

Share and Cite:

Kalebaila, K. and Fairbridge, C. (2014) UV Photocatalytic Degradation of Commercial Naphthenic Acid Using TiO2-Zeolite Composites. Journal of Water Resource and Protection, 6, 1198-1206. doi: 10.4236/jwarp.2014.612109.

1. Introduction

Naphthenic acids (NAs) are found naturally in crude oils or oil sands bitumen and are an oxidative product of petroleum hydrocarbons. The oil sand reserves are highly-biodegraded petroleum that are viscous and tar-like and are often produced by steam assisted gravity drainage. Surface mining is also employed to recover bitumen involving an alkaline hot water extraction process. After the extraction process, the tailings consisting of residual bitumen and slurry of sand, silt, clay, are retained in ponds to permit sedimentation of solids resulting in overflowing water called oil sand process water. Naphthenic acid contaminated water is thought to be toxic to aquatic life by interfering with gas exchange and metabolic processes in plants and fish. [1] [2] The availability of carboxylic groups in the NA structure enhances pipeline and machinery corrosion by reacting with metal ions. The amount of NA in tailings pond water is determined by the total acid number or TAN. The higher the TAN value is, the higher the amount of naphthenic acid and the poorer the tailings water are.

Among the various methods of reducing the concentration and toxicity of naphthenic acids in contaminated water, chemical treatment involving use of oxidants such as ozone, permanganate, and chlorine has been proven but the high operating costs coupled with production of hazardous by-products is problematic. Compared to chemical processing, a low cost technology is bioremediation which relies on the use of microorganisms to remove organic wastes. It has been shown that microorganisms found in some local tailing ponds can metabolize surrogate NAs, but the biodegradation occurred at very slow rates [3] - [5] . The development of membrane bioreactors has enhanced bioremediation processes compared to traditional biological treatments, [6] nonetheless, research in this field is ongoing as it is not yet clear whether bioremediation is effective in conventional oilfield water.

Photocatalytic oxidation is emerging as an innovative approach for treatment of organic pollutants including NAs. It has been reported that UV-B (280 - 315 nm) and UV-C (200 - 280 nm) wavelengths are suitable for most waste water treatments, with the optimal wavelength at 254 nm ideal for remediation of naphthenic acids, where the photocatalysts are either immersed in the contaminated water as a slurry or used in a fixed-bed reactor [7] - [9] . Photocatalytic degradation rates are strongly dependent on the efficiency of adsorption of pollutants on the catalysts, thus, good photocatalyst design is essential for effective adsorption and subsequent degradation of naphthenic acids. Structure modification of the parent TiO2 includes improvement in surface area by incorporating high surface area matrices such as silica (SiO2) and zeolites, addition of chelating agents to trap pollutants, and addition of ions to increase visible light absorption [10] [11] . In this work, the photoreduction of a complex commercial naphthenic acid in water using UV-light in the presence of TiO2 prepared in a zeolite matrix was investigated. Any compositional and/or concentration changes in naphthenic acid before and after UV irradiation were followed by GC-MS with electron impact mode.

2. Materials Section

The as-prepared TiO2-zeolitecomposites (Z-TiO2) were prepared by wet impregnation method as described in the literature [12] [13] . About 32 mL of titanium isopropoxide, Ti(OiPr)4 and 7 mL of acetyl acetone were dissolved in a mixture of 100 mL of isopropyl alcohol and 6 mL of water. Then 10 g of commercial zeolite CBV780 (Zeolyst) was added to the solution and left to stir for 12 hours at room temperature. The mixture was then heated to 120˚C in an Isotemp Muffle Furnace 750 Series (Fisher Scientific), leading to formation of a gelatinous product and the temperature maintained for 8 hours until the product was dry. The dried composites denoted as Z-TiO2 were finally annealed at 500˚C for 2 hours and subsequently sieved to 46 - 60 final mesh size.

The complex naphthenic acid was purchased from Sigma-Aldrich and used without further purification. The physical properties of the naphthenic acid included a density of 0.92 g/mL, solubility in water of 0.05 g/L and boiling point range of 106˚C - 334˚C. For studies, the naphthenic acid was diluted by dissolving 2.07 mL of acid in 600 mL water and 200 mL methanol resulting in a turbid mixture with a final concentration of 0.25 weight%.

3. Results and Discussion

Surface Area and Pore Sizes: The surface area, pore sizes and volumes were determined by the BET (Brunauer, Emmett, and Teller) and BJH (Barrett, Joyner, and Halenda) isotherm models using the ASAP 2020 software on the Micromeritics 2020 physisorption analyzer. The analysis were performed using nitrogen gas as the adsorbate at −196˚C. Samples were initially degassed at 350˚C for 1 hour and then at 110˚C for 4 hours under vacuum in order to remove any adsorbed contaminants from the surface. The BET surface area and the BJH pore sizes and volumes (desorption) of the calcined samples were determined in the pressure ranges of 0.05 - 0.3 and 0.5 - 1.0, respectively, producing a type IV isotherm (Figure 1) [14] . The surface area of the commercial zeolite (780 m2/g) decreases upon addition of TiO2 to 619 m2/g while the average pore diameter increased (4.6 nm) compared to the microporous zeolites (Table 1). Conversely, addition of zeolite to TiO2 increased the surface area compared to 50 m2/g of commercial TiO2.

Figure 1. Nitrogen adsorption/desorption isotherms of Z-TiO2 at −196˚C.

Table 1. Surface area, pore sizes and pores volumes of Z-TiO2 and commercial solids.

Diffuse Reflectance UV-Vis Spectroscopy: The light absorbing properties were determined using UV-VIS diffuse reflectance spectroscopy on a PerkinElmer spectrometer Lambda 45 calibrated for 0% and 100% transmission with a BaSO4 standard. The band-gap energies were estimated using E = hc/l = 1240/l, where h is Planck’s constant, c is speed of light and; l is the absorption onset wavelength. The onset wavelength was determined by extrapolating the rise in % reflectance versus the baseline (Figure 2). The results show that Z-TiO2 has a distinctive UV absorption similar to commercial TiO2-P25 at 367 nm. In contrast, UV spectrum of the zeolite could not be determined since the Al2O3 and SiO2 components in the zeolite have very high band-gap energies in excess of 7 eV (177 nm) that exceed the instrument range [15] .

Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS): DRIFTS spectra were recorded on a Bruker Tensor 27 spectrometer using liquid nitrogen cooled HgCdTe detector and OPUS version 6 software. The samples were prepared using KBr as the background and loaded into a sealable reaction chamber inside a praying mantis (Harrick Scientific). The diffuse reflectance infrared spectra (Figure 3) of TiO2-P25, zeolite CBV 780 and as-prepared composite (Z-TiO2) showed a small sharp peak at 3737 cm−1 attributed to terminal OH groups on Al-OH, Si-OH in the zeolite and Ti-OH from Degussa P25. Coordinated water molecules (H-O-H) exhibit a broad peak centered around 3300 cm−1 while the peak at 1622 cm−1 is due to isolated OH groups on the solid surface [16] . The Z-TiO2 composite show nearly all features of pure zeolite containing several peaks from 2003 cm−1 to 775 cm−1. Although, most TiO2 vibrational features are masked by the strong zeolite vibrations in the IR spectra, UV diffuse reflectance data of Z-TiO2 confirmed the presence of TiO2 from the absorption at 338 nm.

Photocatalysis Reactions: About 150 mg of the powdered catalyst and 100 mL of stock solution of NA were placed in a cylindrical glass reactor of a total volume of 405 mL. The mixture was kept at 25˚C using a Thermo Fisher Temperature bath under constant stirring with a magnetic stir bar during the course of the reactions. Initially, the catalyst/NA mixtures were kept in the dark up to 48 hours and then exposed to UV light using a Newport Oriel 1000 W high pressure Hg(Xe) lamp fitted with a 280 - 400 nm beam turning dichroic mirror (Figure 4). Headspace aliquots from dark (control) and UV light were manually injected into a GC-MS every 50 minutes. A Hewlett-Packard 6890 Series II GC was used for sample introduction into the mass spectrometer. The GC program run from 45˚C to a final temperature of 350˚C at 6˚C/min and held for 5 min. The GC-MS

Figure 2. UV diffuse reflectance spectra of (a) TiO2-P25 (b) Z-TiO2 photocatalysts.

Figure 3. Infrared reflectance spectra of (a) TiO2-P25 (b) zeolite CBY780 and (c) Z-TiO2 photocatalysts.

Figure 4. Set-up of the UV light source using 1000 W Hg(Xe) lamp.

transfer line was kept at 305˚C. A Hewlett-Packard Model 5973 mass-selective detector (MSD) in the electron ionization mode was used to obtain all mass spectra and analyzed by GC/MSD ChemStation version B.0403 using the Wiley 275 L database.

After 48 hours in the dark, the analysis of a headspace aliquot from the mixture of NA and Z-TiO2 (Figure 5) shows atmospheric CO2 at 0.28 mins present in the sealed vessel, while naphthenic acid appears has a broad hump around 5 - 21 mins. The relative abundances of atmospheric CO2 and naphthenic acid stayed relatively constant during 48 hours of equilibration. The adsorption equilibration of NA and zeolite has been reported to initially occur by H-bond interaction between the –OH in the –COOH group of the acid and the O atom of Al-O and Si-O in clays [17] . The naphthenic acid hump consists of multiple components ranging in boiling point from 104˚C to 334˚C. When UV light was illuminated on the mixture for 1 hour, the GC spectrum shows a 45% increase in the intensity of CO2 (Figure 6). After 3 hours of UV irradiation, there is a further 10% increase in the intensity of CO2 (Figure 7). By the 3rd day of continued UV illumination, the CO2 intensity had increased up to a maximum of 93%, while the NA intensity continued to decrease until no more could be detected from the gas phase (Figure 8). The rise in the concentrations of CO2 may indicate that the COOgroups in the naphthenic acids are converted to CO2. It has been reported that naphthenic acids containing multi-carboxylic groups are more susceptible to decarboxylation by photooxidation [18] . The lack of detectable naphthenic acids in the headspace aliquots after 3 days of UV light exposure on NA and Z-TiO2 does not necessarily mean that all the acids in the mixture have been photooxidized. It is likely that there is some acid still adsorbed strongly to the surface of the catalyst that does not escape into the gas form. UV photooxidation of naphthenic acid was repeated

Figure 5. GC-MS spectra of head-space aliquots from mixture of Z-TiO2 and naphthenic acid at 25˚C kept in the dark for 48 hours.

Figure 6. GC spectra of headspace gas from UV irradiation on Z-TiO2 and naphthenic acid at 25˚C for 1 hour.

Figure 7. GC spectra of headspace gas from UV irradiation on Z-TiO2 and naphthenic acid at 25˚C for 3 hours. Abundance of CO2 has increased compared to dark conditions.

Figure 8. GC spectra of headspace gas from UV irradiation on Z-TiO2 and naphthenic acid at 25˚C over 3 days. Continued increase in CO2 intensity. Inset: expanded region of the GC showing decline in abundance of the acid.

several times and the same results were obtained showing that UV light plays a major role in reducing the amount of naphthenic acids in water.

An interesting observation was that the magnetic stir bars obtained from the mixture of naphthenic acid and Z-TiO2 under UV light had a sticky and black oily substance (Figure 9). Even after heating the stir bars at 150˚C for 2 hours, the oily substance was still present. On the other hand, magnetic stirs bars obtained when no light was shown on the NA and Z-TiO2 mixture appeared very different. In this case, only a white solid presumably the catalyst was on the stir bars, and when heated at 150˚C for 2 hours, the white solid dried up and could easily be brushed off. Work is underway to characterize these deposits on the stir bars.

Total Acidity Measurements: In order to determine if the decrease in the abundance of naphthenic acid from UV photocatalysis with Z-TiO2 was due to the actual loss of −COOH groups, the total acidity of the mixtures were determined by thermometric titration, a method developed for finding the total acid number (TAN) of crude oil. Thermometric titrations involve an acid-base reaction where 0.1 mol/L KOH in isopropyl alcohol (IPA) is titrated with the acids until the endpoint is reached. The endpoint is recognized by the inflection of the titration curve and the concentration of TAN is reported as mg/KOH/g according to ASTM WK 26624. The TAN values were determined by an automated Metrohm 859 Titrotherm with Tiamo software.

In a typical titration, 5 g of pure NA liquid was titrated with KOH/IPA (Figure 10) and the TAN value for the commercial acid was found to be 229 mgKOH/g. The TAN of the diluted acid (0.25%) dropped to 3.61 mg KOH/g. TAN measurements were also performed for (a) the mixture of naphthenic acid and catalyst (b) filtrates, before and after light illumination. Table 2 shows that the TAN of diluted stock naphthenic acid and that of the mixture (dark) are in the same range, but the TAN for the mixture of acid and catalyst exposed to UV over 3 days decreased to 1.05 mg KOH/g. This change in TAN after UV photo-radiation on naphthenic acid and Z-TiO2 suggests a reduction in the number of −COOH groups in the NA consistent with observations from GC-MS

Figure 9. Appearance of stir bars from a mixture of Z-TiO2 and naphthenic acid (Right) after exposure to UV light for 5 days and (Left) kept in dark for a week.

Figure 10. Thermometric titration curve of NA with KOH in IPA. The pink curve is the second derivative of the titration curve. EP1 is the end-point.

Table 2. TAN values for the various fractions from dark and UV conditions.

data, Figures 6-8. Total acid number measurements on the corresponding filtrates also showed a decrease in acidity from dark to UV exposed reactants. However, the TAN values for the filtrates are very low compared to those from the mixtures. Most likely, some of the oily acid was stuck on the catalyst surface and did not pass through the filter. As a precaution, thermometric titrations require a damping volume of titrant ~0.20 mL to avoid falsely picking an endpoint that is actually noise incurred during the very initial start of titration. If the volume is exactly 0.20 mL, it is likely that the true endpoint did not exceed the damping area. A higher sample volume should be used. Although, the endpoints of the filtrate solutions were very close to 0.20 mL regardless of sample size, the change in acidity mirrors the data obtained from mixtures as well as GC-MS.

4. Conclusion

In conclusion, UV photocatalysis of the multi-component naphthenic acid showed that the components of the acid were photodegraded to CO2. Although the amount of detectable naphthenic acid in the gas phase decreased dramatically over time, this is not an indication that all the naphthenic acid in solution had been oxidized. Acidity measurements on the reactant mixtures before and after UV irradiation provided further evidence of a decrease in acidity after UV treatment. The fact that a TAN value was obtained for UV treated mixture verified that some naphthenic acid is adsorbed on surface of catalysts and could not to be detected in the gas phase over time. Future efforts for the continuation of this project would involve a) conduct naphthenic acid photoreduction using a variety of UV and VIS-photocatalysts;(b) use real naphthenic acid containing water i.e. obtain oil sand processed water for such studies.

Acknowledgements

This work was supported by the Government of Canada’s interdepartmental Program for Energy Research and Development (PERD), Program 1.1.3 Petroleum Conversion for Cleaner Air. The suggestions, comments and review by Patricia Arboleda were very helpful and appreciated.

NOTES

*Corresponding author.

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1] Clemente, J.S. and Fedorak, P.M. (2005) A Review of the Occurrence, Analyses, Toxicity, and Biodegradation of Naphthenic Acids. Chemosphere, 60, 585-600.
http://dx.doi.org/10.1016/j.chemosphere.2005.02.065
[2] Kamaluddin, M. and Zwiazek, J.J. (2002) Naphthenic Acids Inhibit Root Water Transport, Gas Exchange and Leaf Growth in Aspen (Populus Tremuloides) Seedlings. Tree Physiology, 22, 1265-1270.
http://dx.doi.org/10.1093/treephys/22.17.1265
[3] Biryukova, O.V., Fedorak, P.M. and Quideau, S.A. (2007) Biodegradation of Naphthenic Acids by Rhizosphere Microorganisms. Chemosphere, 67, 2058-2064.
http://dx.doi.org/10.1016/j.chemosphere.2006.11.063
[4] Johnson, R.J., Smith, B.E., Sutton, P.A., McGenity, T.J., Rowland, S.J. and Whitby, C. (2011) Microbial Biodegradation of Aromatic Alkanoic Naphthenic Acids is Affected by the Degree of AlkylSide Chain Branching. ISME Journal, 5, 486-496.
http://dx.doi.org/10.1038/ismej.2010.146
[5] Scott, A.C., Mackinnon, M.D. and Fedorak, P.M. (2005) Naphthenic Acids in Athabasca Oil Sands Tailings Waters Are Less Biodegradable than Commercial Naphthenic Acids. Environmental Science Technology, 39, 8388-8394.
http://dx.doi.org/10.1021/es051003k
[6] McKenzie, N., Yue, S., Liu, X., Ramsay, B.A. and Ramsay, J.A. (2014) Biodegradation of Naphthenic Acids in Oils Sands Process Waters in an Immobilized Soil/Sediment Bioreactor. Chemosphere, 109, 164-172.
http://dx.doi.org/10.1016/j.chemosphere.2014.02.001
[7] Headley, J.V., Du, J.L., Peru, K.M. and McMartin, D.W. (2009) Electrospray Ionization Mass Spectrometry of the Photodegradation of Naphthenic Acids Mixtures Irradiated with Titanium Dioxide. Journal of Environmental Science and Health, Part A: Toxic/Hazardous Substances and Environmental Engineering, 44, 591-597.
http://dx.doi.org/10.1080/10934520902784625
[8] McMartin, D.W., Headley, J.V., Friesen, D.A., Peru, K.M. and Gillies, J.A. (2004) Photolysis of Naphthenic Acids in Natural Surface Water. Journal of Environmental Science and Health, Part A: Toxic/Hazardous Substances and Environmental Engineering, 39, 1361-1383.
http://dx.doi.org/10.1081/ESE-120037839
[9] Mishra, S., Meda, V., Dalai, A.K., McMartin, D.W., Headley, J.V. and Peru, K.M. (2010) Photocatalysis of Naphthenic Acids in Water. Journal of Water Resource and Protection, 2, 644-650.
http://dx.doi.org/10.4236/jwarp.2010.27074
[10] Allen, E.W. (2008) Process Water Treatment in Canada’s Oil Sands Industry: II. A Review of Emerging Technologies. Journal of Environmental Engineering and Science, 7, 499-524.
http://dx.doi.org/10.1139/S08-020
[11] Bahnemann, D. (2004) Photocatalytic Water Treatment: Solar Energy Applications. Solar Energy, 77, 445-459.
http://dx.doi.org/10.1016/j.solener.2004.03.031
[12] Kalebaila, K.K. and Klabunde, K.J. (2010) An Inorganic Oxide TiO2-SiO2-Mn Aerogel for Visible-Light Induced Air Purification. In: Erickson, L.E., Koodali, R.T. and Richards, R.M., Nanoscale Materials in Chemistry: Environmental Applications, American Chemical Society, Washington DC, 207-223.
[13] Zhang, W., Zou, L. and Wang, L. (2009) Photocatalytic TiO2/Adsorbent Nanocomposites Prepared via Wet Chemical Impregnation for Wastewater Treatment: A Review. Applied Catalysis A: General, 371, 1-9.
http://dx.doi.org/10.1016/j.apcata.2009.09.038
[14] Webb, P.A. and Orr, C. (1997) Analytical Methods in Fine Particle Technology. Micromeritics Instrument Corp, Norcross.
[15] Tahir, D., Kwon, H.L., Shin, H.C., Oh, S.K., Kang, H.J., Heo, S., et al. (2010) Electronic and Optical Properties of Al2O3/SiO2 Thin Films Grown on Si Substrate. Journal of Physics D: Applied Physics, 43, 255301-255400.
[16] Halasz, I., Agarwal, M., Marcus, B. and Cormier, W.E. (2005) Molecular Spectra and Polarity Sieving of Aluminum Deficient Hydrophobic H-Y Zeolites. Microporous and Mesoporous Materials, 84, 318-331.
http://dx.doi.org/10.1016/j.micromeso.2005.05.040
[17] Zou, L., Han, B., Yan, H., Kasperski, K.L., Xu, Y. and Hepler, L.G. (1997) Enthalpy of Adsorption and Isotherms for Adsorption of Naphthenic Acid onto Clays. Journal of Colloid and Interface Science, 190, 472-475.
http://dx.doi.org/10.1006/jcis.1997.4898
[18] Frank, R.A., Kavanagh, R., Burnison, B.K., Arsenault, G., Headley, J.V., Peru, K.M., Van Der Kraak, G. and Solomon, K.R. (2008) Toxicity Assessment of Collected Fractions from an Extracted Naphthenic Acid Mixture. Chemosphere, 72, 1309-1314.
http://dx.doi.org/10.1016/j.chemosphere.2008.04.078

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.