Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite

Manoj Singla, D. Deepak Dwivedi, Lakhvir Singh, Vikas Chawla

Department of Mechanical Engineering, BBSBEC, Fatehgarh Sahib (Pb.), India.
Department of Mechanical Engineering, R.I.E.I.T., Railmajra, Distt. Nawanshahr (Pb.)-144533,India.
Department of Metallurgical & Materials Engineering, I.I.T. Roorkee (Uttaranchal), India.

DOI: 10.4236/jmmce.2009.86040                

Abstract

Metal Matrix Composites (MMCs) have evoked a keen interest in recent times for potential applications in aerospace and automotive industries owing to their superior strength to weight ratio and high temperature resistance. The widespread adoption of particulate metal matrix composites for engineering applications has been hindered by the high cost of producing components. Although several technical challenges exist with casting technology yet it can be used to overcome this problem. Achieving a uniform distribution of reinforcement within the matrix is one such challenge, which affects directly on the properties and quality of composite material. In the present study a modest attempt has been made to develop aluminium based silicon carbide particulate MMCs with an objective to develop a conventional low cost method of producing MMCs and to obtain homogenous dispersion of ceramic material. To achieve these objectives two step-mixing method of stir casting technique has been adopted and subsequent property analysis has been made. Aluminium (98.41% C.P) and SiC (320-grit) has been chosen as matrix and reinforcement material respectively. Experiments have been conducted by varying weight fraction of SiC (5%, 10%, 15%, 20%, 25%, and 30%), while keeping all other parameters constant. The results indicated that the ‘developed method’ is quite successful to obtain uniform dispersion of reinforcement in the matrix. An increasing trend of hardness and impact strength with increase in weight percentage of SiC has been observed. The best results (maximum hardness 45.5 BHN & maximum impact strength of 36 N-m.) have been obtained at 25% weight fraction of SiC. The results were further justified by comparing with other investigators.

Keywords

Metal Matrix Composites MMC’s, Silicon Carbide SiC.

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1]	S. Skolianos. Mater. Sci. Eng. A210 (1990), pp. 72–82.
[2]	Shen, Y.L., Williams, J.J., Piotrowski, G., Chawla, N. and Guo, Y.L. (2001), “Correlation between tensile and indentation behavior of particle reinforced metal matrix composites: a numerical and experimental study,” Acta Materialia, Vol. 49 (16), pp. 3219-3229.
[3]	Llyod, D.J., Lagace, H., Mcleod, A. and Morris, P.L. (1989), “Microstructural aspects of aluminium silicon carbide particulate composites produced by a casting method”, Materials Science and Engineering, Vol. 107, pp. 73-80.
[4]	M.K. Surappa. J. Mater. Proc. Tech. 63 (1997), pp. 325–333.
[5]	D.M. Skibo, D.M. Schuster, L. Jolla, Process for preparation of composite materials containing nonmetallic particles in a metallic matrix, and composite materials made by, US Patent No. 4 786 467, 1988
[6]	Balasivanandha, S., Kaarunamoorthy, L., Kaithiresan, S. and Mohan, B. (2006), “Influence of stirring speed and stirring time on distribution of particles in cast metal matrix composite”, Journal of Material Processing Technology, Vol. 171, pp. 268-273.
[7]	Hashim, J., Looney, L. and Hashmi, M.S.J. (2001), “The wettability of SiC particles by molten aluminum alloy”, Journal of Materials Processing Technology, Vol. 119 (1-3), pp. 324-328.
[8]	Hashim, J., Looney, L. and Hashmi, M.S.J. (2001), “The enhancement of wettability of SiC particles in cast aluminium matrix composites”, Journal of Materials Processing Technology, Vol.119 (1-3), pp. 329-335.
[9]	Richard A. Flinn “ Fundamentals of Metal Casting” Addisson Wesley Series in Metallurgy and Materials, pp. 11-32.
[10]	C.G.Kang, S.Ray and P.K.Rohatgi, Mater. Sci. Eng. A188, 193 (1994).
[11]	Doel.T.J.A, Lorretto.M.H and Bowen.P. (1993), “Mechanical Properties of aluminium based particulate metal matrix composites”, Journal of composites, Vol. 24, pp. 270-275.
[12]	Gnjidi, X., Boi, D. and Mitkov, M. (2001), “The influence of SiC particles on compressive properties of metal matrix composites”, Materials Characterization, Vol. l47 (2), pp. 129-138.
[13]	Gu, J., Zhang, X. and Gu, M. (2004), “Mechanical properties and damping capacity of (SiC + AL2O3.SiO2) / Mg hybrid metal matrix composite”, Journal of Alloys and Compounds, Article in press.
[14]	Gupta, M. and Qin, S. (1997), “Effect of interfacial characteristics on the failuremechanism mode of a SiC reinforced A1 based metal-matrix composite”, Journal of Materials Processing Technology, Vol. 67(1-3), pp. 94-99.
[15]	Kaynak, C. and Boylu, S. (2005), “Effects of SiC [particulates on the fatigue behavior of an Al-alloy matrix composite”, Journal of Material & Design, Article in press, corrected proof.
[16]	Kok, M. (2005), “Production and mechanical Properties of AL2O3 particle-reinforced 2024 aluminium alloy composites”, Journal of Materials Processing Technology, Vol. 161, pp. 381-387.
[17]	Lucas, J.P., Stephens, J.J. and Greulich, F.A. (1991), “The effect of reinforcement stability on composition redistribution in cast aluminium metal matrix composites”, Materials Science and Engineering, Vol. 131 (2), pp. 221-230.
[18]	Mares, M. (2001), “ Some issues on tailoring possibilities for mechanical properties of particulate reinforced metal matrix composites” Journal of Optoelectronics and Advanced Materials, Vol. 3 (1), pp. 119 – 124.
[19]	Naher, S., Brabazon, D. and Looney, L. (2003), “Simulation of the stir casting process”, Journal of Materials Processing Technology, Vol. 143-144, pp. 567-571.
[20]	Naher, S., Brabazon, D. and Looney, L. (2004), “Development and assessment of a new quick quench stir caster design for the production of metal matrix composites”, Journal of Material Processing Technology, Vol. 166, pp. 430-439.
[21]	Nakae, H. and Wu, S. (1998), “Engulfment of Al2 O3 particles during solidification of aluminium matrix composites”, Materials Sciences and Engineering, Vol. 252 (2), pp. 232-238.
[22]	Nesarikar, A.R., Tewari, S.N. and Graham, E.E. (1993), “Room temperature wear characteristics of Al2O3-particle-reinforced aluminum alloy composite”, Materials Science and Engineering A, Vol. 147 (2), pp. 191-199.
[23]	Ourdjini, A., Chew, K.C. and Khoo, B.T. (2001), “Settling of silicon carbide particles in case metal matrix composites”, Journal of Materials Processing Technology, Vol. 116 (1), pp. 72-76.
[24]	Poole, W.J. and Charras, N. (2005), “ An experimental study on the effect of damage on the stress-strain behavior for Al-Si model composites”, Material Science & Engineering, Vol. 406 (1-2), pp. 300-308.
[25]	Quin, S., Chen, C.and Zhang, G. (1999), “The effect of particle shape on ductility of SiC reinforced 6061 Al matrix composite”, Material Science and Engineering, Vol. 272(2), pp. 363-370.
[26]	Ravi, N.V. and Dwarakadasa, E.S. (2006), “Effect of matrix strength on the mechanical properties of Al-Zn-Mg/SiC composites”, Composites Part A 31, pp.1139-1145.
[27]	Rajnesh, T. (2005), “Synthesis and tribological characterization of in-situ cast Al-TiC composites”, Journal of Wear, 259, pp. 569-576.
[28]	Rohatgi, P.K., Sobezak, J., Asthana, R. and Kim, J.K.(1998), “Inhomogeneities in silicon carbide distribution in stirred liquids-water model study for synthesis of composites”, Materials Science and Engineering , Vol.252 (1), pp. 98-99.
[29]	Samuel, A.M., Liu, H. and Samuel, F.H. (1993), “On the castability of Al-Si/SiC particle reinforced metal matrix composites: Factors affecting fluidity and soundness”, Composite Science and Technology, Vol. 49, Issue 1, pp.1-12.
[30]	Wannasin, .J. (2005), “Fabrication of metal matrix composites by a high- pressure centrifugal infiltration process”, Journal of Materials Processing Technology, Vol. 169, pp. 143-149.