Study at Two Dimensions of Thermal Transfer through a Fibers Panel Subjected to Climatic Constraints in Dynamic Frequency Regulations Established ()
1. Introduction
Controlling energy consumption in homes during hot weather, or in cold rooms requires, among other things, good thermal insulation. Problems of cost of synthetic materials and end-of-life management lead us to propose use of biodegradable materials. Thus study of thermal behavior of material for use in thermal insulation [1] [2] is of major interest in search for energy control.
Several methods for calculating transient or established dynamic regimes [3] [4] are developed for simulation of thermal behavior within material.
We propose in this study resolution in dynamic regime established by imposing boundary conditions particular to panel of fibers.
Temperature curves along material depth or in lateral direction will allow us to evaluate thermal behavior of fibers material. Influence of the thermal exchange coefficient on front face will be highlighted.
2. Theory
Equation of heat transfer through rectangular material to absence of internal source, is written in two dimensions (Figure 1):
(1)
α is thermal diffusivity coefficient of the material (m2·s−1) and is expressed as
(2)
where:
- ρ (kg·m−3)is density of material,
- C (J·kg−1·K−1) is mass thermal capacity,
- λ (W·m−1·K−1) is thermal conductivity of material.
For method by separating variables, we propose:
(3)
(3) in (1) leads to following expressions:
(4)
Equations (5)-(7) are deduced from following relationships (8):
with
(8)
Solutions of preceding equations give:
(9)
(10)
(11)
which gives general expression of temperature through material in form:
(12)
We apply to system boundary conditions, Equations (13)-(16), reflecting heat exchanges between faces of material and external environment:
with:
(17)
and
(18)
is the temperature imposed on the front face.
We pose:
(19)
(20)
we obtain:
(21)
(22)
(23)
Graphical representations of Figure 2 and Figure 3 correspond to transcendental Equation (22) and Equation (23) for obtaining eigenvalues
and
respectively and given in Table 1.
Table 1. Positives eingenvalues:
.
Solution of equation of heat can thus be written:
(24)
To explain the coefficient
, we pose:
(25)
It can be written as:
(26)
with:
(27)
(28)
(29)
We replace
in (38) by its expression obtained by (37), we obtain:
(30)
We apply normalization condition (31):
(31)
(32)
(33)
We finally get:
(34)
Coefficient k is relative to the thermal effisitivity, it defines transmission of heat to wall of material:
.
k = 0: we have perfect thermal insulation behavior on surface of material;
k = 1: we have perfect conductor behavior on surface of material.
We worked with k = 0.85.
Taking into account results obtained in previous studies [4] [5], we consider an average value of coefficient translating heat exchanges on surface of material: k = 0.85.
3. Results and Discussion
Solution (25) of heat equation made it possible to draw simulation curves of Figures 4-7 showing evolution of temperature inside material.
Figure 4 shows evolution of temperature according depth inside material in frequency modulation. We have an accumulation of heat resulting in heating of material for x < 0.03 m there is no heat exchange on the lower face y = 0. For x > 0.03 m, we have decrease in amplitude of temperature which tends at end of
Figure 4. Evolution of temperature according to depth. Ti = 10˚C, Te = 35˚C, λ = 0.174 W·m−1·˚C−1, h1 = h4 = 0.5 W·m−2·˚C−1.
Figure 5. Evolution of temperature along lateral axis. Ti = 10˚C, Te = 35˚C, λ = 0.174 W·m−1·˚C−1, h1 = h4 = 0.5 W·m−2·˚C−1.
Figure 6. Evolution of temperature according to depth. Influence of heat exchange coefficient. Ti = 10˚C, Te = 35˚C, λ = 0.174 W·m−1·˚C−1, h4 = 0.5 W·m−2·˚C−1.
Figure 7. Evolution of temperature along lateral axis. Influence of heat exchange coefficient. Ti = 10˚C, Te = 35˚C, λ = 0.174 W·m−1·˚C−1, h4 = 0.5 W·m−2·˚C−1.
excitation towards amplitude of initial temperature of material; material warms up slightly.
Figure 5 shows evolution of temperature along lateral axis. Overheating phenomenon in vicinity of y = 0 is confirmed because there is no heat exchange with respect to outside. Beyond y = 0.02 m, material temperature fluctuates around 10˚C, which corresponds to low overheating of material.
Figure 6 and Figure 7 show influence of heat exchange coefficient at front face on temperature. Exchange coefficient contributes significantly to heating of wall and propagation of heat along axis of depths. On other hand, along lateral axis, this influence is practically nil.
4. Validation
Methods of thermal characterization in numerical simulation [6] or analytical [7] [8] present results of evolutions of temperature and density of heat flux comparable through different materials.
5. Conclusion
Starting from resolution of equation of two-dimensional heat in frequency dynamic regime, we obtained curves which show thermal behavior of fibers material subjected to different climatic constraints. Thermal insulating nature of material is highlighted by an evanescent tendency of external excitation inside material.