Fabrication of Sm-Based Perovskite-Type Oxide Thin-Films and Gas Sensing Properties to Acetylene

Tomohisa Tasaki, Satoko Takase, Youichi Shimizu

Department of Applied Chemistry, Kyushu Institute of Technology, Tobata, Japan.

DOI: 10.4236/jst.2012.22011                

Abstract

Sm-based perovskite-type oxide (SmMeO₃: Me = Cr, Mn, Fe, Co) thin-films could be synthesized by a wet-chemical method using an acetylacetone—Poly(Vinyl Pyrrolidone) (PVP) polymeric precursor method at 750℃. The perovskite-type oxide thin-films were tried to apply an acetylene gas sensor based on AC impedance spectroscopy. Among the oxides tested, SmFeO₃ thin-film sensor showed good sensor responses in which the AC impedance at 20 kHz was depending on acetylene gas concentration between 2 ppm and 80 ppm at 400℃.

Keywords

Perovskite-Type Oxide; Thin-Film; Ac Impedance; Acetylene; Gas Sensor

1. Introduction

Lanthanoid-based perovskite-type oxides, such as LnMeO₃ (Ln: lanthanoids, Me: transition metals), have been well-known as functional inorganic materials having a wide range of applications for electrode materials of the alkaline fuel cell [1], gas sensor [2-10], ion sensor [11], and for high-performance catalysts for the complete oxidation of hydrocarbons or CO, and NO reduction [12]. Among the lanthanoid-transition metal perovskite-type oxides, Sm-based oxides seem to be interesting materials as they have the largest amount of adsorbed oxygen [13]. For example, the Sm-based perovskite-type oxide sensors have been reported to detect NO_x [14], volatile organic compounds [15], ethanol [16] and so on. It is also wellknown that the oxide thin-film devices have good properties as electrochemical devices. So far, oxide thin-film with a perovskite-type structure have been prepared by dry processes such as sputtering and electron-beam deposition methods [17,18], as well as the wet processes of the sol-gel method mainly starting from metal alkoxides or organic acid salts [19,20]. They can field high-quality oxide thin-films; however, they still have some problems, such as relatively low cost performance and lack of handling of the chemicals using the sol-gel method. Consequently, in this work it is focused attention on a wet process to evade such problem, and perovskite-type oxide could be synthesized by a polymer precursor with metal nitrates contained constituent elements [21,22]. By the way, acetylene (C₂H₂) is widely used as the fuel for cutting and welding metals, so there are also strong needs to detect acetylene as combustible gas. Recently, it has known that small amount of acetylene is to be generated from depleted insulating oils of an oil-immersed transformer. Thus, the acetylene gas sensor could be applicable as a new type of maintenance’s marker of the transformers, especially for the large sized transformers set in remote areas.

The conventional chromatographic method for acetylene detection has high accuracy and is widely used, but it is not suitable for on-site monitoring because of the limited portability as well as the high operating cost. So far, considerable efforts have been directed to develop high performance gas sensors for monitoring acetylene, such as electrochemical sensors [23], and semiconductor type sensors [24,25], however, the sensor for detection acetylene have been seldom reported.

In this study, the Sm-based perovskite-type oxide thinfilm as the material of an acetylene sensor was picked up and systematically evaluated about wet-chemical synthesize of perovskite-type oxide thin-film [26] and the C₂H₂ sensing properties of the prepared oxide thin-film.

2. Experimental

2.1. Synthesis of Perovskite-Type Oxide Thin-Films

Perovskite-type oxide (SmMeO₃: Me = Cr, Mn, Fe, Co) thin-films were synthesized by a polymer precursor method [26] as shown in Figure 1. Metal nitrates were dissolved in Ethylene Glycol (EG) solvent with Polyvinylpyrrolidone (PVP) (3.75 wt%) and acetylacetone (AcAc), as a polymer additive and a coordination agent,

Figure 1. Experimental procedure for preparation of perovskitetype oxide SmMeO₃ (Me = Cr, Mn, Fe, Co) thin-films and Sm-Co xerogel powder.

respectively. The solution thus prepared was spin-coated on an alumina substrate with Au interdigitated electrodes at 4000 rpm, and finally sintered at 750˚C in air. The spin-coating and sintering processes were repeated several times to adjust the thickness.

The samples were analyzed by X-ray diffraction using CuKα radiation (XRD: JEOL JDX3500K), field emission type scanning electron microscope (FE-SEM: JEOL JSM- 6500F/III), and thermo gravimetric-differential thermal analysis (TG-DTA: Rigaku 8120H). Electrical conductivities of the thin-films were measured in air (PO₂ = 0.21 atm) at the temperature range between 200˚C and 500˚C in the frequency range from 50 Hz to 5 MHz with applied voltage of 0.5 V by AC impedance method (LCR meter: HIOKI 3532-50).

2.2. Fabrication of Sensor Devices

Figure 2 shows schematic diagram of the measurement apparatus. The perovskite-type oxide thin-film sensor device was connected to LCR meter with Au lead wires attached with a silver paste covered with an inorganic adhesive. Gas sensing properties were investigated by AC impedance method using the LCR meter at 400˚C - 500˚C. Sample gases, containing C₂H₂ were prepared from a parent gas, i.e., 2 - 80 ppm C₂H₂ diluted with nitrogen, by mixing with nitrogen and/or oxygen, were flowed at a total flow rate of 100 cm³/min. The oxygen partial pressure of the sample gases was fixed at 0.21 atm. Sensitivities of the responses of the sensors were defined as Equation (1);

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1]	D. B. Meadowcroft, “Low-Cost Oxygen Electrode Material,” Nature, Vol. 226, No. 5248, 1970, pp. 847-848. doi:10.1038/226847a0
[2]	M. Yang, L. Huo, H. Zhao, S. Gao and Z. Rong, “Electrical Properties and Acetone-Sensing Characteristics of LaNi1–xTixO3 Perovskite System Prepared by Amorphous Citrate Decomposition,” Sensors and Actuators B: Chemical, Vol. 143, No. 1, 2009, pp. 111-118. doi:10.1016/j.snb.2009.09.003
[3]	L. Zhang, H. Qin, P. Song, J. Hu and M. Jiang, “Electric Properties and Acetone-Sensing Characteristics of La1–xPbx-FeO3 Perovskite System,” Materials Chemistry and Physics, Vol. 98, No. 2-3, 2006, pp. 358-362. doi:10.1016/j.matchemphys.2005.09.041
[4]	E. L. Brosha, R. Mukundan, R. Lujan and F. H. Garzon, “Mixed Potential NOx Sensors Using Thin Film Electrodes and Electrolytes for Stationary Reciprocating Engine Type Applications,” Sensors and Actuators B: Chemical, Vol. 119, No. 2, 2006, pp. 398-408. doi:10.1016/j.snb.2005.12.044
[5]	G. N. Chaudhari, S. V. Jagtap, N. N. Gedam, M. J. Pawar and V. S. Sangawar, “Sol-Gel Synthesized Semiconducting LaCo0.8Fe0.2O3-Based Powder for Thick Film NH3 Gas Sensor,” Talanta, Vol. 78, No. 3, 2009, pp. 1136-1140. doi:10.1016/j.talanta.2009.01.030
[6]	K. Sahner, D. Schonauer, R. Moos, M. Matam and M. L. Post, “Effect of Electrodes and Zeolite Cover Layer on Hydrocarbon Sensing with p-Type Perovskite SrTi0.8-Fe0.2O3–δ Thick and Thin Films,” Journal of Materials Science, Vol. 41, No. 18, 2006, pp. 5828-5835. doi:10.1007/s10853-006-0299-x
[7]	E. Delgado and C. R. Michel, “CO2 and O2 Sensing Behavior of Nanostructured Barium-Doped SmCoO3,” Materials Letters, Vol. 60, No. 13-14, 2006, pp. 1613-1616. doi:10.1016/j.matlet.2005.11.080
[8]	Y. Shimizu and N. Yamashita, “Solid Electrolyte CO2 Sensor Using NASICON and Perovskite-Type Oxide Electrode,” Sensors Actuators B: Chemical, Vol. 64, No. 1-3, 2000, pp. 102-106. doi:10.1016/S0925-4005(99)00491-8
[9]	Y. L. Chai, D. T. Ray, G. J. Chen and Y. H. Chang, “Synthesis La0.8Sr0.2Co0.5Ni0.5O3–δ Thin Films for High Sensitivity CO Sensing Material Using the Pechini Process,” Journal of Alloys and Compounds, Vol. 333, No. 1-2, 2002, pp. 147-153. doi:10.1016/S0925-8388(01)01688-7
[10]	L. Malavasi, C. Tealdi, A. Montenero, J. M. Tulliani, P. Moggi, M. Guglielmi, G. Flor, A. Lorenzi, A. Martucci, L. Montanaro and G. Chiodelli, “Materials Development for CO-Detection with Improved Selectivity through Catalytic Activation,” Sensors Actuators B: Chemical, Vol. 118, No. 1-2, 2006, pp. 121-128. doi:10.1016/j.snb.2006.04.008
[11]	Y. Shimizu, A. Ishikawa, K. Iseki and S. Takase, “Perovskite-Type Oxide-Based Electrode: A New Sensor for Hydrogen-Phosphate Ion,” Journal of the Eletrochemical Society, Vol. 147, No. 10, 2000, pp. 3931-3934. doi:10.1149/1.1393998
[12]	H. M. Zhang, Y. Shimizu, Y. Teraoka, N. Miura and N. Yamazoe, “Oxygen Sorption and Catalytic Properties of La1–xSrxCo1–yFeyO3 Perovskite-Type Oxides,” Journal of Catalysis, Vol. 121, No. 2, 1990, pp. 432-440. doi:10.1016/0021-9517(90)90251-E
[13]	H. Aono, E. Traversa, M. Sakamoto and Y. Sadaoka, “Crystallographic Characterization and NO2 Gas Sensing Property of LnFeO3 Prepared by Thermal Decomposition of Ln-Fe Hexacyanocomplexes, Ln[Fe(CN) 6]nH2O, Ln = La, Nd, Sm, Gd, and Dy,” Sensors Actuators B: Chemical, Vol. 94, No. 2, 2003, pp. 132-139. doi:10.1016/S0925-4005(03)00328-9
[14]	M. C. Carotta, G. Martinelli, Y. Sadaoka, P. Nunziante and E. Traversa, “Gas-Sensitive Electrical Properties of Perovskite-Type SmFeO3 Thick Films,” Sensors Actuators B: Chemical, Vol. 48, No. 1-3, 1998, pp. 270-276. doi:10.1016/S0925-4005(98)00011-2
[15]	M. Tomoda, S. Okano, Y. Itagaki, H. Aono and Y. Sadaoka, “Air Quality Prediction by Using Semiconducting Gas Sensor with Newly Fabricated SmFeO3 Film,” Sensors Actuators B: Chemical, Vol. 97, No. 2-3, 2004, pp. 190-197. doi:10.1016/j.snb.2003.08.013
[16]	M. Zhao, H. Peng, S. Fang and J. Hu, “Microstructure, Electrical and Ethanol-Sensing Properties of Perovskite-Type SmFe0.7Co0.3O3,” Sensors Actuators B: Chemical, Vol. 130, No. 2, 2008, pp. 609-613. doi:10.1016/j.snb.2007.10.017
[17]	C. M. Chiu and Y. H. Chang, “The Influence of Microstructure and Deposition Methods on CO Gas Sensing Properties of La0.8Sr0.2Co1–xNixO3?δ Perovskite Films,” Sensors Actuators B: Chemical, Vol. 54, No. 3, 1999, pp. 236-242. doi:10.1016/S0925-4005(99)00117-3
[18]	M. J. Montenegro, T. Lippert, S. Muller, A. Weidenkaff, P. R. Willmott and A. Wokaun, “Pulsed Laser Deposition of Electrochemically Active Perovskite Films,” Applied Surface Science, Vol. 197-198, 2002, pp. 505-511. doi:10.1016/S0169-4332(02)00326-4
[19]	T. Kumagai, H. Yokota, K. Kawaguchi, W. Kondo and S. Mizuta, “Preparation of Superconducting YBa2Cu3O7–δ Thin Films by the Dipping-Pyrolysis Process Using Organic Acid Salts,” Chemistry Letters, Vol. 16, No. 8, 1987, pp. 1645-1646. doi:10.1246/cl.1987.1645
[20]	H. J. Hwang and M. Awano, “Preparation of LaCoO3 Catalytic Thin Film by the Sol-Gel Process and Its NO Decomposition Characteristics,” Journal of the European Ceramic Society, Vol. 21, No. 10-11, 2001, pp. 2103-2107. doi:10.1016/S0955-2219(01)00181-9
[21]	K. Tsuchida, S. Takase and Y. Shimizu, “Sol-Gel Synthesis of Perovskite-Type Oxide Thin-Film with Metal Organic-Acid and Its Application to Amperometric Hydrogen-Phosphate Ion Sensor,” Sensors and Materials, Vol. 16, No. 3, 2004, pp. 171-180.
[22]	Y. Pimtong-Ngam, S. Jiemsirilers and S. Supothina, “Preparation of Tungsten Oxide-Tin Oxide Nanocomposites and Their Ethylene Sensing Characteristics,” Sensors and Actuators A: Physical, Vol. 139, No. 1-2, 2007, pp. 7-11. doi:10.1016/j.sna.2006.10.032
[23]	L. R. Jordan and P. C. Hauser, “Electrochemical Sensor for Acetylene,” Analytical Chemistry, Vol. 69, No. 14, 1997, pp. 2669-2672. doi:10.1021/ac9700585
[24]	Q. Qi, T. Zhang, X. Zheng, H. Fan, L. Liu, R. Wang and Y. Zeng, “Electrical Response of Sm2O3-Doped SnO2 to C2H2 and Effect of Humidity Interference,” Sensors Actuators B: Chemical, Vol. 134, No. 1, 2008, pp. 36-42. doi:10.1016/j.snb.2008.04.011
[25]	S. T. Marshall, D. K. Schwartz and J. W. Medlin, “Selective Acetylene Detection through Surface Modification of Metal-Insulator-Semiconductor Sensors with Alkanethiolate Monolayers,” Sensors Actuators B: Chemical, Vol. 136, No. 2, 2009, pp. 315-319. doi:10.1016/j.snb.2008.11.026
[26]	Y. Shimizu and T. Murata, “Sol-Gel Synthesis of Perovskite-Type Lanthanum Manganite Thin Films and Fine Powders Using Metal Acetylacetonate and Poly(Vinyl Alcohol),” Journal of the American Ceramis Society, Vol. 80, No. 10, 1997, pp. 2702-2704. doi:10.1111/j.1151-2916.1997.tb03178.x
[27]	S. M. Bukhari and J. B. Giorgi, “Cobaot Doped Sm0.95-Ce0.05FeO3–δ for Detection of Reducing Gases,” Journal of the Electrochemical Society, Vol. 158, No. 6, 2011, pp. J159-J164. doi:10.1149/1.3570674
[28]	S. M. Bukhari and J. B. Giorgi, “Tuneability of Sm(1–x)-CexFeO3±λ Perovskites: Thermal Stability and Electrical Conductivity,” Solid State Ionics, Vol. 180, No. 2-3, 2009, pp. 198-204. doi:10.1016/j.ssi.2008.12.002
[29]	S. Luo, G. Fu, H. Chen, Z. Liu and Q. Hong, “Gas-Sensing Properties and Complex Impedance Analysis of Ce-Added WO2 Nanoparticles to VOC Gases,” Solid-State Electronics, Vol. 51, No. 6, 2007, pp. 913-919. doi:10.1016/j.sse.2007.04.010
[30]	P. H. T. Ngamou and N. Bahlawane, “Chemical Vapor Deposition and Electric Characterization of Perovskite Oxides LaMO2 (M = Co, Fe, Cr and Mn) Thin Films,” Journal of Solid State Chemistry, Vol. 182, No. 4, 2009, pp. 849-854. doi:10.1016/j.jssc.2008.12.017