Production of Ethanol from Cassava Peelings Using a Developed Percolation Reactor ()
1. Introduction
Lignocellulose wastes are accumulated every year in large quantities, causing environmental problems. However, due to their chemical composition which consist of complex sugars and other compounds of interest, they could be utilized for the production of a number of value added products, such as ethanol, food additives, organic acids, enzymes, and others [1]. Therefore, besides the environmental problems caused by their accumulation in the nature, the non-use of these materials constitutes a loss of potentially valuable sources. Lignocellulosic materials predominantly contain a mixture of carbohydrate polymers (cellulose and hemicellulose), lignin, extractives, and ashes [2]. These constituents are bonded together by chains and these chains are packed by hydrogen bond in so called “elementary fibrils” originally considered to be 3 to 4 nm wide and contain about 36 chains, although larger crystalline fibrils up to 16 nm were also discovered [3]. The constituents are closely associated with each other constituting the cellular complex of the vegetal biomass.
Cassava (Manihotesculenta Crantz) has been an important crop used for food and industrial purposes in most Africa countries. Cassava is the chief source of dietary food energy for the majority of the people living in the lowland tropics, and much of the sub-humid tropics of West and Central Africa [4]. Its production is vital to the economy of Nigeria at the country is the world’s largest producer of the farm produce. Cassava is composed of large amounts of starch (20% - 35% fresh and 80.6% dry weight) [5] [6] and total dry matter (38.6%) [7] , and has been reported to have the smallest water-footprint (21 m3/GJ) compared to all other crops [8]. Based on the above reasons, cassava has recently gained considerable attention as in important lignocellulosic biomass for the production of bioenergy [6]. The most important characteristics of cassava is that it contains C3 and C4 photosynthetic root and these promotes carbohydrates production to some extent that the plant is suitable for industrial utilization.
In processing cassava tuber, the biomass left behind include peelings, leaves and roots, and in most cases, the biomass waste is not used for any economical purposes. Apart from the stem that may be used for re-planting, the peelings are usually disposed of indiscriminately, thus leading to environmental pollution. In the best cases, the current utilisation of cassava peelings includes its potential re-placement for maize in animal feed, especially for ruminant animals. However, the drawback in this include; its low protein content (<6%) [9] , and the presence of anti-nutrients such as hydrocyanic acid, tannic acid, oxalic acid which could produce hazardous effects on ruminant animals [10]. Consumption of cassava wastes is therefore greatly reduced, leaving the residue as non-valuable wastes in the environment compartment. However, the wastes could be of tremendous value if utilized for energy generation.
In Nigeria, the quantity of cassava peelings generated is quite huge in places where gari (dried cassava flour), fufu (wet cassava flour) and Starch are produced and converting such wastes to energy resources would consume the wastes, sanitize the environment and benefit the nation economically. One of the ways to unlock this great potential of the waste is by getting valuable products out of it, hence, a reactor was being designed to hydrolyse the waste. In this research work, a percolation reactor was designed as described by [11] to check its efficiency for the hydrolysis of agricultural waste such as cassava peelings.
Many researchers have reported on the use of different reactors such as Stir-tank, Plug flow, Batch reactors etc. for the hydrolysis of biomass. Batch reactor has been the most widely us for kinetic study of hydrolysis and laboratory study of bioethanol derived there from [12] and [13]. However, [11] reported the use of percolation reactor towards an integrated biorefinery using a dried distillers’ grains and achieved a high pentose yield using a percolation reactor with liquid re-circulation. Hitherto, information about the use of percolation reactor for the hydrolysis of cassava waste is scanty and has not been found reported in literature. Therefore, this research work preferentially considered percolation reactor over others due to its advantages at reducing acid consumption, higher yield of hemicellulose sugars and lower yield of sugar degradation products [14] and [15]. Furthermore, unlike the batch and plug flow reactors, this percolation reactor does not need a solid or liquid separation as the solid are placed in the percolation baskets and do not flow with the liquid. Therefore, damages due to particle attrition are minimal in this reactor when compared to other types of reactor.
2. Material and Methods
2.1. Materials
The Percolation reactor is made of two concentric cylinders. The inner cylinder is of 270 mm diameter, 456 mm height, 3 mm thickness and made of galvanised plate while the outer cylinder is of 370 mm diameter, 456 mm height, 3 mm thickness and made of mild steel. Mild steel was used because it is available, cheap and has the ability to withstand high temperature. The galvanised plate was used for the inner cylinder because of its relatively lower cost and corrosion resistant properties. A lagging material (fibreglass) which is 50 mm in thickness was sandwiched between the inner and outer cylinders to prevent heat lost or gain in the reactor chamber. A discharge outlet was incorporated into the reactor for the collection of the hydrolysed samples at various predetermined time intervals. The base of the reactor chamber was made conical in shape, for an easy discharge of the hydrolysate, at the end of each hydrolysis process and to facilitate cleaning after use. A perforated material holding basket of 297 microns mesh size, is placed inside the inner cylinder and could be removed or replaced with the aid of an attached handle. A heating compartment through which the hydrolyzate circulates was attached to the reactor and powered by a 3000 W heating element. The temperature of the component was controlled and regulated by a Type-K thermocouple and a temperature controller at desired set points. The rate of hydrolyzate circulation and pressure was controlled by a variable speed pump of 0.5 hpcapacity. A control box that superintends and monitors the entire operation of the percolation reactor was designed and incorporated into the reactor. The reactor was designed based on the following considerations: rapid pumping of hydrolyzate, reliable heat supply for heating the system, rapid heat transfers into the reactor, avoiding heat loss and maintaining a set temperature during operation. The schematic diagram of the Percolation reactor is shown in Figure 1.
Sample Collection and Pretreatment
The cassava peelings used for this research work was obtained at various Gari processing sites at Ilara-Mokin, Ondo State of Nigeria. 20 kg of the fresh cassava peelings was obtained from various processing sites at Ilara-Mokin, cleaned to remove adhering sand grains, dirt, dust and of other impurities. The cleaned peels were sundried for 3 days to reduce the moisture content to about 6 - 8 wt%; and then ball milled to obtain 0.5≤ and ≥0.3 mm particle size (Figure 2) using Denver ball mill Model 230994. This particle dimension provided a high surface area per unit volume of the feedstock and prevented particle clogging on the material holding basket. The particles attain the desired hydrolysis temperature, within a very short residence time because of their small linear dimensions and permit easy acid penetration through their pores. The complex organic structural bond is broken through this process and complex sugars are reduced to simple sugars, in a process termed hydrolysis.
Figure 1. A percolation reactor for the hydrolysis of agricultural biomass waste.
2.2. Methods
The conversion of agricultural biomass wastes such as cassava peelings to ethanol is not obtained through a direct route, hence the developed percolation reactor (Figure 1) will be used in breaking its structural bonds and thus releasing the fermentable sugar before been fermented. Figure 3 outlined the conversion stages of the biomass from pre-treatment process to bioethanol production stage.
2.2.1. Hydrolysis
500 g of milled cassava peelings was collected and hydrolysed using 250 mL of 0.5 M dilute sulphuric acid (H2SO4) in 2 litres of distilled water at a temperature of 100˚C for a duration of 2 hours. The hydrolysis of the feedstock samples was done in three replicate experiments. The hydrolyzate (Figure 4) obtained from the reaction showed an acidic property and thereafter subjected to neutralization process.
2.2.2. Neutralization of the Cassava Hydrolyzate
10 g of NaOH was dissolved in 500 mL of distilled water to obtain a solution of 0.5 M sodium-hydroxide. The solution of NaOH (0.01 M) was added in drops to the hydrolysate and the neutralization level was measured to be 7.2 with a pH meter.
2.2.3. Fermentation of the Cassava Peelings Hydrolyzate
The cassava hydrolyzate was fermented at room temperature (Figure 5). 20 g of yeast (Saccharomyces cerevisiae) was added to the hydrolyzate to aid fermentation and the fermentation lasted for 7 days. As fermentation days reached the last day, CO2 is shown to have evolved at the surface of the fermented liquor (Figure 5).
2.2.4. Distillation of the Fermented Product
The fermented liquor was distilled using Liebig condenser apparatus. The fermented liquor was distilled at a temperature ranging from 77˚C - 80˚C. The distillate collected at that temperature was re-distilled and the distillate was collected at a temperature of 78˚C - 78.4˚C where the standard boiling temperature for ethanol production is 78.3˚C.
Figure 3. Conversion stages of cassava peels biomass to Ethanol.
Figure 4. Hydrolyzate from cassava peelings.
Figure 5. Fermentation of the cassava peels hydrolyzate.
3. Results
3.1. Fourier Transform Infrared (FT-IR) Test of the Ethanol Produced
A functional group identification test was carried on the ethanol using a Fourier Transform Infrared (FT-IR) spectrophotometer at the Department of Chemistry, University of Ibadan, Ibadan, Oyo State Nigeria. The result is presented in Figure 6 and Table 1.
3.2. Fuel Properties of Ethanol Produced
Table 2 shows the fuel properties of the ethanol produced compared to the standard properties of ethanol reported by [16].
Table 1. FT-IR structural information of the cassava peel bioethanol.
Table 2. Fuel properties of ethanol produced compared to the standard properties.
Figure 6. FT-IR spectrum of the ethanol produced.
4. Discussion
The FT-IR spectra in Figure 6 range from high energy cosmic rays (high frequency, short wavelength) to very low energy microwaves (low frequency, long wavelength). The spectra of the ethanol were measured as absorbance (Figure 6). The percentage of light that passed through the ethanol sample for every wavelength was shown in Figure 6. The graph of the absorbance (Figure 6) explains that, the highest level of wavelength sample is predominantly characterised by OH group. Alcohol (OH-group) is said to occur at a wavelength ranging from 3500 - 3000 cm−1 and the spectra indicate the presence of OH-group at 3280 cm−1 which is a strong alcohol (Table 1). Other functional groups were also found in the ethanol and they belong to the alkane, nitrile, alkyne and aromatic group (Table 1).
5. Conclusion
The percolation reactor was developed and fabricated using locally available materials, while ethanol production was achieved using cassava peelings as feedstock. The reactor is simple to operate, easy to maintain and affordable. The reactor was used to hydrolyse 500 g of cassava peelings thrice in a replicating experiment that produced a mean value of 118 mL of ethanol per run. The physicochemical, thermochemical and energy characteristics of ethanol produced was determined (Table 2) and compared with the properties of ethanol reported by [16] , while the spectraanalysis (Figure 6 and Table 1) was done using F.T.I.R spectrophotometer. These properties were consistent with standards aside from a minute observed difference of 0.04 g/mL in its density, which highly suggests that the product is ethanol. Therefore, the use of the percolation reactor for the hydrolysis of biomass waste prior to the production of ethanol is an effective way of generating fermentable sugar from the biomass wastes. In addition, hydrolysis is a promising route for converting biomass wastes to chemical and energy products, consume accumulation of agricultural wastes in the environment, prevents its biodegradation and promote cleaner environment.