Investigation into the Deep Drawability of 0.1%C Eutectoid Steel

Abstract

The phenomenon of anisotropism in most rolled products necessitates that the rolling direction that enhances desirable mechanical property is established. In this paper, the comparative deep drawability of as-received and annealed mild steel containing about 0.1%C was investigated. The flat steel sample was divided into two and classified as as-received and heat treated respectively. The heat treated sample was obtained by annealing at 950°C after been soaked for 5 hours and deep drawn at ambient temperatures (35°C - 42°C). From both samples, circular specimens were machine- blanked parallel to the rolling directions inclined at 0°, 45° and 90° respectively and were prepared for deep drawability test while rectangular specimens were prepared for tensile test. Both specimens, as-received and annealed were then sub- jected to tensile, cupping and microstructural analyses. Results show that the contribution to increased formability at 90° rolling direction seems to have come from the spheroid-like pearlite grains induced during annealing while the sta- bility of spread observed was achieved through a modest increase in strength. Thus, the resistance of annealed eutectoid steel to cupping is quite minimal at 90° to the rolling direction. The desirable drawability characteristics developed by the annealed eutectoid steel specimen are: cup-height, 30 mm maximum and ear, 6.4% maximum.

Share and Cite:

Adeosun, S. , Sekunowo, O. and Balogun, S. (2012) Investigation into the Deep Drawability of 0.1%C Eutectoid Steel. Journal of Minerals and Materials Characterization and Engineering, 11, 1034-1038. doi: 10.4236/jmmce.2012.1110107.

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1] W. Miller, J. Zhuang, A. Bottema, P. Witterbrood, P. De Smet, A. Haszler and A. Vieregge, “Recent Development in Aluminium Alloys for the Automotive Industry,” Ma- terials Science and Engineering A, Vol. 280, No. 1, 2000, pp. 37-49.
[2] Z. Q. Sun, W. Y. Yang, J. J. Qi and A. M. Hu, “Deforma- tion Enhanced Transformation and Dynamic Recrystalli- sation of Ferrite in a Low Carbon Steel during Multipass Hot Deformation,” Materials Science and Engineering A, Vol. 334, No. 1-2, 2002, pp. 201-206.
[3] V. M. Segal, V. I. Reznikov and V. I. Kopylov, “Process of Plastic Structure Formation in Metals,” Science and Engineering Publishers House, Minsk, 1994, pp. 45-76.
[4] J. Zrnik, J. Drrnek, Z. Novy, V. Dobatlein and O. Ste- jsleel, “Structure Evolution during Severe Warm Plastic Deformation of Carbon Steel,” Advance Materials Sci- ence, Vol. 210, No. 1, 2005, pp. 45-55.
[5] C. Oldani and A. Aliya, “Low Carbon Steel Sheets Ob- tained by Reactive Annealing,” Latin American Applied Research, Vol. 32, No. 2, 2002, pp. 137-140.
[6] Y. Mehta and P. S. Mishra, “Thermo-Mechanical Proc- essing of Iron-Phosphorous-Carbon Alloys,” Journal of Minerals and Materials Characterization and Engineer- ing. Vol. 10, No. 1, 2011, pp. 93-100.
[7] L. Storojeva, D. Ponge, R. Kaspar and D Raabe, “De- velopment of Microstructure and Texture of Medium Carbon Steel during Heavy Warm Deformation,” Acta Materialia, Vol. 52, No. 8, 2004, pp. 2209-2220. doi:10.1016/j.actamat.2004.01.024
[8] B. Karlsson and G. Linden, “Plastic Deformation of Eu- tectoid Steel with Different Cementite Morphologies,” Materials Science and Engineering, Vol. 17, No. 1, 2003, pp. 153-164.
[9] K. A. Bello, S. B. Hassan and O. Aponbiede, “Effects of Austenitising Conditions on the Microstructures and Me- chanical Properties of Martensitic Steel with Dual Matrix Structure,” Journal of Minerals and Materials Charac- terisation and Engineering, Vol. 11, No. 1, 2011, pp. 69-83.
[10] C. Zener and J. H. Hollomon, “Effect of Strain Rate upon Plastic Flow of Steel,” Journal of Applied Physics, Vol. 15, No. 1, 2009, pp. 22-32.
[11] F. Fereshteh-Saniee and M. H. Montazeran, “A Compara- tive Estimation of the Forming Load in the Deep Drawing Process,” Journal of Materials Processing Technology, Vol. 140, No. 1-3, 2003, pp. 555-561.
[12] J. Toribio, “Relationship between Microstructure and Strength in Eutectoid Steels,” Materials Science and En- gineering A, Vol. 387-389, 2004, pp. 227-230. doi:10.1016/j.msea.2004.01.084
[13] E. Erdin, H. Aykul and.S. Tunalioglu, “Forming of High Strength/Low Formability Metal Sheets at Elevated Tem- peratures,” Mathematical and Computational Applica- tions, Vol. 10, No. 3, 2005, pp. 331-340.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.