3 - 10 GHz Ultra-Wideband Low-Noise Amplifier Using Inductive-Series Peaking Technique with Cascode Common-Source Circuit ()
Abstract
The objective of this paper is to investigate a ultra-wideband (UWB) low noise amplifier (LNA) by utilizing a two-stage cascade circuit schematic associated with inductive-series peaking technique, which can improve the bandwidth in the 3-10 GHz microwave monolithic integrated circuit (MMIC). The proposed UWB LNA amplifier was implemented with both co-planer waveguide (CPW) layout and 0.15-μm GaAs D-mode pHEMT technology. Based on those technologies, this proposed UWB LNA with a chip size of 1.5 mm x 1.4 mm, obtained a flatness gain 3-dB bandwidth of 4 - 8 GHz, the constant gain of 4 dB, noise figure lower than 5 dB, and the return loss better than –8.5 dB. Based on our experimental results, the low noise amplifier using the inductive-series peaking technique can obtain a wider bandwidth, low power consumption and high flatness of gain in the 3 - 10 GHz. Finally, the overall LNA characterization exhibits ultra-wide bandwidth and low noise characterization, which illustrates that the proposed UWB LNA has a compact size and favorable RF characteristics. This UWB LNA circuit demonstrated the high RF characterization and could provide for the low noise micro-wave circuit applications.
Share and Cite:
C. Wu, T. Lin, C. Chang and H. Wu, "3 - 10 GHz Ultra-Wideband Low-Noise Amplifier Using Inductive-Series Peaking Technique with Cascode Common-Source Circuit,"
Wireless Engineering and Technology, Vol. 2 No. 4, 2011, pp. 257-261. doi:
10.4236/wet.2011.24034.
Conflicts of Interest
The authors declare no conflicts of interest.
References
[1]
|
WPAN High Rate Alternative PHY Task Group 3a (TG3a), IEEE 802.15, 2007.
http://www.ieee802.org/15/pub/TG3a.html
|
[2]
|
G. R. Aiello and G. D. Rogerson, “Ultra-Wideband Wireless Systems,” IEEE Microwave Magazine, Vol. 4, No. 2, 2003, pp. 36-47. doi:10.1109/MMW.2003.1201597
|
[3]
|
Y.-J. Lin, S. S. H. Hsu, J.-D. Jin and C. Y. Chan, “A 3.1 - 10.6 GHz Ultra-Wideband CMOS Low Noise Amplifier with Current-Reused Technique,” IEEE Microwave and Wireless Components Letters, Vol. 17, No. 3, 2007, pp. 232-234. doi:10.1109/LMWC.2006.890503
|
[4]
|
C.-F. Liao and S.-I. Liu, “A Broadband Noise—Canceling CMOS LNA for 3.1 - 10.6-GHz UWB Receivers,” IEEE Journal of Solid-State Circuits, Vol. 42, No. 2, 2007, pp. 329-339. doi:10.1109/JSSC.2006.889356
|
[5]
|
A. Bevilacqua and A. M. Niknejad, “An Ultra-Wideband CMOS LNA for 3.1 to 10.6 GHz Wireless Receiver,” IEEE Solid-State Circuits Conference (ISSCC) Digest of Technical Papers, Vol. 39, No. 12, 2004, pp. 382-383.
|
[6]
|
C.-H. Wu, C.-H. Lee, W.-S. Chen and S.-I. Liu,“CMOS Wideband Amplifiers Using Multiple Inductive-Series Pe- aking Technigue,” IEEE Journal of Solid-State Circuits, Vol. 40, No. 2, 2005, pp. 548-552.
doi:10.1109/JSSC.2004.840979
|
[7]
|
S. Shekhar, X. Li, and D. J. Allstot, “A CMOS 3.1 - 10.6 GHz UWB LNA Employing Stagger-Compensated Series Peaking,” Radio Frequency Integrated Circuits (RFIC) Symposium, San Francisco, 2006, pp. 63-66.
|