Refining bioreactor design using autoclavable glass bonding

Abstract

Selecting the right design of bioreactors is crucial for guaranteeing the reproducibility of bioprocesses. Up to now, conventionally designed bioreactors consist typically of melted or clamped joints. Since melting of borosilicate glass leads to large deformed areas along the joint, the desired geometric reproducibility is not ensured. Moreover, clamping complicates and greatly restricts the bioreactor design. Bonding, however, is advantageous in that it does not alter the material joined and it is easy to use. Furthermore, it has been recently shown that specially developed glass bonding techniques withstand multiple autoclaving cycles. The current research investigated practice-relevant parameters influencing the lifespan of epoxy-or (urethane) acrylate-bonded glass bioreactors. Hereby, the influence of cleaning and sensitivity to fermentation compounds (ethanol and acetic acid) was quantified using glass-glass and glass-stainless steel specimens. Whereas cleaning did not adversely affect the durability of glass bonds, high concentrations of the fermentation compounds ethanol and acetic acid resulted in accelerated corrosion and subsequent bond failure. Moreover, no effect of eight different epoxy and (urethane) acrylate adhesives was observed on selected model organisms Escherichia coli K12 and Hansenula polymorpha wild type. Another objective of this study was to refine the design of two small-scale bioreactors (ca. 250 mL) by replacing clamps and melted joints by adhesive joints. It was found that the bonded bioreactors yielded a higher geometric reproducibility than that of conventional melted or clamped ones. In conclusion, bonded glass joints greatly enhance the geometric reproducibility of bioreactors and, in turn, the reproducibility of bioprocesses. As glass bonding is easy to handle, it opens up new opportunities to design bioreactors that had been previously too expensive and complicated.

Share and Cite:

Bähr, C. , Stammen, E. , Zahlten, S. , Böhm, S. , Dilger, K. and Büchs, J. (2011) Refining bioreactor design using autoclavable glass bonding. Advances in Bioscience and Biotechnology, 2, 233-243. doi: 10.4236/abb.2011.24034.

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1] Büchs, J. (2001) Introduction to advantages and problems of shaken cultures. Biochemical Engineering Journal, 7(2), 91-99.
[2] Maier, U. and Büchs, J. (2001) Characterisation of the gas–liquid mass transfer in shaken bioreactors. Biochemical Engineering Journal, 7(2), 99–106.
[3] Maier, U., Losen, M. and Büchs, J. (2004) Advances in understanding and modeling the gas–liquid mass transfer in shake flasks. Biochemical Engineering Journal, 17(3), 155–167.
[4] Galindo, E., Flores, C., Larralde-Coronab, P., Corkidi-Blanco, G., Antonio Rocha-Valadez, J. and Serrano-Carreón, L. (2004) Production of 6-pentyl-α-pyrone by Trichoderma harzianum cultured in unbaffled and baffled shake flasks. Biochemical Engineering Journal, 18(1), 1-8.
[5] Calam, C.T. (1996) Shake flask fermentations. In: Demain, A.L., Solomon, N.A., Eds., Manual of Industrial Microbiology and Biotechnology, American Society for Microbiology, Washington, DC, 59–65.
[6] Anderlei, T., Zang, W., Papaspyrou, M. and Büchs, J. (2004) Online respiration activity measurement (OTR, CTR, RQ) in shaken flasks. Biochemical Engineering Journal, 17(3), 187-194.
[7] Peter, C.P., Lotter, S., Maier, U. and Büchs, J. (2004) Impact of out-of-phase conditions on screening results in shaking flask experiments. Biochemical Engineering Journal, 17(3), 205-215.
[8] Losen, M., Fr?lich, B., Pohl, M. and Büchs, J. (2004) Effect of Oxygen Limitation and Medium Composition on Escherichia coli Fermentation in Shake-Flask Cultures. Biotechnology Progress, 20(4), 1062-1068.
[9] Gaden, E.L. (1962) Improved shaken flask performance. Biotechnology and Bioengineering, 4(1), 99-103.
[10] McDaniel, L.E., Bailey, E.G. and Zimmerli, A. (1965) Effect of oxygen supply rates on growth of Escherichia coli. Part I. Studies in unbaffled and baffled shake flasks. Applied and Environmental Microbiology, 13(1), 109-114.
[11] Delgado, G., Topete, M. and Galindo, E. (1989) Interaction of cultural conditions and end-product distribution in Bacillus subtilis grown in shake flasks. Applied Microbiology and Biotechnology, 31(3), 288-292.
[12] Moore, J.H., Davis, C.C. and Coplan, M.A. (1991) Building scientific apparatus – A Practical Guide to Design and Construction, Perseus Books, Reading Masachusettes, 55-58.
[13] Storhas, W. (1994) Bioreaktoren und periphere Enrichtungen. Vieweg Verlag, Braunschweig/ Wiesbaden, 165-166.
[14] Krahe, M. (2007) Biochemical Engineering. In: Ullmann’s Biotechnology and Biochemical Engineering, Vol. 2, 1st Edition, Wiley-VCH, Weinheim, 655.
[15] Adams, R.D., Comyn, J. and Wake, W.C. (1997) Structural adhesives joints in engineering, 2nd Edition, Chapamn & Hall, London.
[16] Gleich, D.M., Van Tooren, M.J.L. and Beukers, A. (2002) Structural bonded joint analysis: An overview. In: Mittal, K.L., Ed., Adhesive Joints: Formation, Characteristics and Testing, Vol. 2, VSP BV, Utrecht, 159-199.
[17] Pocius, A.V. (2002) Adhesion and Adhesives Technology – An Introduction, 2nd Edition, Hanser, München, 2-5.
[18] B?hr, C., Stammen, E., Thiele, R., B?hm, S., Dilger, K. and Büchs, J. (2011) Withstanding frequent Steam Sterilisation: Innovative Technique to Bond Glass and Stainless Steel Composites in Biotechnology and Endoscopic Medicine, paper unpublished.
[19] Dien, B.S., Cotta, M.A. and Jeffries, T.W. (2003) Bacteria engineered for fuel ethanol production: current status. Applied Microbiology and Biotechnology, 63(3), 258-266.
[20] Mielenz, J.R. (2001) Ethanol production from biomass: technology and commercialization status. Current Opinion in Microbiology, 4(3), 324-329.
[21] McMillan, J.D. (1997) Bioethanol production: Status and prospects. Renewable Energy, 10(2-3), 295-302.
[22] Wiegel, J. (1980) Formation of ethanol by bacteria. A pledge for the use of extreme thermophilic anaerobic bacteria in industrial ethanol fermentation processes. Cellular and Molecular Life Sciences, 36(12), 1434-1446.
[23] Han, K., Lim, H.C. and Hong, J. (1992) Acetic acid formation in Escherichia coli fermentation. Biotechnology and Bioengineering, 39(6), 663-671.
[24] Fukaya, M., Park, Y.S. and Toda, K. (1992) Improvement of acetic acid fermentation by molecular breeding and process development. Journal of Applied Microbiology, 73(6), 447-454.
[25] de Ory, I., Romero, L.E. and Cantero, D. (1999) Maximum yield acetic acid fermenter. Bioprocess and Biosystems Engineering, 21(2), 187-190.
[26] Park, Y.S., Ohtake, H. and Toda, K. (1990) A kinetic study of acetic acid production by liquid-surface cultures of Acetobacter aceti. Applied Microbiology and Biotechnology, 33(3), 259-263.
[27] Devantier, R., Pedersen, S. and Olsson, L. (2005) Characterisation of very high gravity ethanol fermentation of corn mash. Effect of glycoamylase dosage, pre-saccharification and yeast strain. Applied Microbiology and Biotechnology, 68(5), 622-629.
[28] Fleury, K., Kalina, V. and Zell, J.J. (1997) Vinegar production. European patent EP 0548552, January, 15, 1997.
[29] Salek, A.T. (2002) Classic techniques for improvement of industrial yeast strains. Part I: Construction of ethanol-resistant and osmophilic industrial strains of Saccharomyces cerevisiae by electrofusion. BioTechnologia, 1, 153-174.
[30] Anderlei, T. and Büchs, J. (2001) Device for sterile online measurement of the oxygen transfer rate in shaking flasks. Biochemical Engineering Journal, 7(2), 157-162.
[31] Rechmann, H., Friedrich, A., Forouzan, D., Barth, S., Schnabl, H., Biselli, M. and Boehm, R. (2007) Characterization of photosynthetically active duckweed (Wolffia australiana) in vitro culture by Respiration Activity Monitoring System (RAMOS). Biotechnology Letters, 29(6), 971-977.
[32] J?nicke, G., Sauter, C., Bux, R. and Haas, J. (2007) Characterisation of Shake Flasks for Cultivation of Animal Cell Cultures. In: Smith, R., Ed., Cell Technology for Cell Products, Springer, Dordrecht, 727–731.
[33] Pe?a, C., Peter, C.P., Büchs, J. and Galindo, E. (2007) Evolution of the specific power consumption and oxygen transfer rate in alginate-producing cultures of Azotobacter vinelandii conducted in shake flasks. Biochemical Engineering Journal, 36(2), 73-80.
[34] Guez, J.S., Müller, C.H., Danze, P.M., Büchs, J. and Jacques, P. (2008) Respiration activity monitoring system (RAMOS), an efficient tool to study the influence of the oxygen transfer rate on the synthesis of lipopeptide by Bacillus subtilis ATCC6633. Journal of Biotechnology, 134(1-2), 121-126.
[35] Scheidle, M., Jeude, M., Dittrich, B., Denter, S., Kensy, F., Suckow, M., Klee, D. and Büchs, J. (2010) High-throughput screening of Hansenula polymorpha clones in the batch compared with the controlled-release fed-batch mode on a small scale. FEMS YeastResearch, 10(1), 83-92.
[36] Wilms, B., Hauck, A., Reuss, M., Syldatk, C., Mattes, R., Siemann, M. and Altenbuchner, J. (2001) High-cell-density fermentation for production of L-Ncarbamoylase using an expression system based on the Escherichia coli rhaBAD promoter. Biotechnology and Bioengineering, 73(2), 95-103.
[37] Jeude, M. (2007) Entwicklung und Anwendung einer Fed-batch-Betriebsweise mit N?hrstofffreisetzungssystemen zur kontrollierten Kultivierung und zum Screening von Mikroorganismen in Schüttelkolben. Ph.D. Dissertation, RWTH Aachen University, Aachen.
[38] Gellissen, G. (2004) Production of recombinant proteins. Wiley-VCH-Verlag GmbH, Weinheim, 307-314.
[39] Jeude, M., Dittrich, B., Niederschulte, H., Anderlei, T., Knocke, C., Klee, D. and Büchs, J. (2006) Fed-batch mode in shake flask by slow-release technique. Biotechnology and Bioengineering, 95(3), 433-436.
[40] St?ckmann, C., Maier, U., Anderlei, T., Knocke, C., Gellissen, G. and Büchs, J. (2003) The oxygen transfer rate as key parameter of Hansenula polymorpha screening cultures. Journal of Industrial Microbiology and Biotechnology, 30(10), 613-622.
[41] Le Bourhis, E. (2008) Glass – Mechanics and Technology. Wiley-VCH Verlag, Weinheim, 208-212.
[42] Frischat, G.H. (2002) Tin ions in float glass cause anomalies. Comptes Rendus Chimie, 5(11), 759-763.
[43] Yates, B.W. and Duffy, A.M. (2008) Statistical Analysis of the Metrological Properties of Float Glass. In: Khounsary, A.M., Morawe, C. and Goto, S., Eds., Advances in X-Ray/EUV Optics and Components III, Proceedings of SPIE, 7077, September 2008, DOI: 10.1117/12.795278.
[44] Hermann, R., Lehmann, M. and Büchs, J. (2003) Characterization of Gas–Liquid Mass Transfer Phenomena in Microtiter Plates. Biotechnology and Bioengineering, 81(2), 178-186.
[45] Akgün, A., Müller, C., Engmann, R. and Büchs, J. (2008) Application of an improved continuous parallel shaken bioreactor system for three microbial model systems. Bioprocess and Biosystems Engineering, 31(3), 193-205.
[46] Armstrong, K.B. (1997) Long-term durability in water of aluminium alloy adhesive joints bonded with epoxy adhesives. International Journal of Adhesion and Adhesives, 17(2), 89-105.
[47] Akgün, A., Maier, B., Preis, D., Roth, B., Klingelh?fer, R. and Büchs, J. (2004) A Novel Parallel Shaken Bioreactor System for Continuous Operation. Biotechnology Progress, 20(6), 1718-1724.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.