Dissemination of information to citizens is a relevant component of governance. Expectedly, viewers tuned to broadcast stations within and outside their localities, expecting their receivers to faithfully reproduce the exact features of the transmitted signal. Akpabuyo is a dense forest zone near the creeks leading to the Atlantic ocean in Cross River State, Nigeria. The location has distinct environmental characteristics that made Akpabuyo Area Council, a challenging location to propagate electromagnetic waves; and therefore recipe for further investigation. Radio frequency analyzer, with 24 channels spectrum, ranging between 46 - 870 MHz (model: RO.VE.R.-“DLM3-T”) was deployed to capture signals from terrestrial television stations (TV). CATV measured signal of TV stations in dB, dB μV and dBmV. Its frequency ranged from 40 - 860 MHz; while varying from channel 1 to channel 69. Measurements taken from Akpabuyo L.G.A. showed the following results: the signal strength received from VHF Channel 11 ranged from 20 dB μV to 49 dB μV. From recorded empirical statistics from the study, 50% of the area received signal from this station above 30 dB μV, while other regions had signals below this value; representing the fringe zone of the frequency. The results obtained from the study relatively showed acceptance with Egli’s model. The study recorded a steady fluctuation between 17 dB μV and 19 dB μV from both propagating stations. However, Channel 27 signal at 519 MHz, had very weak signal coverage in Akpabuyo Local Government Area; with signal strength dropped to as low as 13 dB in many parts of the rural area. The study discovered that the state’s broadcasting stations, both at UHF and VHF channels did not transmit successfully across this densely forest (rural) location. Remedial measures such as installing Repeater stations at different locations as signal booster were recommended.
The broadcast industry plays a major role in information dissemination to citizens. It is one major out-fit where every citizen can be informed of major events worldwide; even when they cannot afford to own a receiver-station. Thus, the availability of television in almost every home cannot be questioned. According to records, about 1.4 billion of the world’s population own television-set; indicating that one out of every five people owns a television. Analysis from research studies shows that China tops the chart with 28.2%, followed by US with 15.5% [
One of the transmission media of information technology is done through VHF (Very High Frequency) and UHF (Ultra High Frequency) bands. These frequency bands are assigned to stations for terrestrial broadcasting. As viewers tuned to broadcast stations within and outside their localities, they expect the television to faithfully reproduce the exact audio and video features transmitted by the broadcasting station’s transmitter: the structural content or shape of object, the tonal content or relative brightness, the motion of the object or kinematic content, sound, color or chromatic content and lastly the stereoscopic content also known as perspective [
Wave could be seen as an oscillation or vibration or disturbance that is characterized by energy transfer that moves through space or object [
Propagation loss has been established to be inevitable as the distance between the transmitting antenna and the receiving antenna increases. As viewers tuned to broadcast stations within and outside their localities, they expect the television to faithfully reproduce the exact audio and video features transmitted by the broadcasting station’s transmitter (Kennedy and Davies, 1993) [
Waves have two main types and they are mechanical and electromagnetic waves. Whereas mechanical waves require material medium for its propagation, electromagnetic waves requires no material medium for its propagation. When an electric current flows through a conductor, it produces a time-varying electric field which in turn acts as a source of magnetic field. These two fields created can sustain and interact with each other giving rise a special form of energy known as electromagnetic wave [
∮ E ⋅ d A = Q e n c l / ϵ ∘ (1)
Equation (1) implies that the surface integral of E over any closed surface equals 1 / ϵ multiplied by the total charge Qencl, where E is the electric field and A represents the area.
∮ B ⋅ d A = 0 . (2)
Equation (2) states that the surface integral of B over any closed surface is zero, where B is the magnetic field.
∮ B ⋅ d l = μ ( i ˛ + ε ∘ d Φ d t E ) (3)
This is also known as Ampere’s law. It implies that both conduction and displacement current act as sources of magnetic field; where ε ∘ is the permittivity of free space, μ ∘ the permeability of free space, and Φ E the electric flux.
∮ E ⋅ d l = − dΦ d t E (4)
Equation (4) is Faraday’s law and implies that a changing magnetic flux induces an electric field. The Heaviside version of this equation using Laplace transform is shown in Equations (5) to (8) below:
∇ ⋅ E = 0 (5)
∇ × E = − ∂ B ∂ t (6)
∇ ⋅ B = 0 (7)
∇ × E = μ ∘ ϵ ∘ ∂ E ∂ t (8)
Deploying the curl of curl to these equations, we obtain Equations (9) and (10) as presented below:
∇ × ( ∇ × E ) = − ∂ ∂ t ∇ × B = − μ ∘ ϵ ∘ ∂ 2 E ∂ t 2 (9)
∇ × ( ∇ × B ) = − ∂ ∂ t ∇ × E = − μ ∘ ϵ ∘ ∂ 2 E ∂ t 2 (10)
Further to the above, applying the vector identity, Equation (11) is derived as:
∇ × ( ∇ × V ) = ∇ ⋅ ( ∇ ⋅ V ) − ∇ 2 V (11)
where V is any vector function in space. And Equation (12),
∇ 2 V = ∇ ⋅ ( ∇ ⋅ V ) (12)
where ∇ V is a dyadic which when operated on by the divergence operator ∇ ⋅ yields a vector. Since
∇ ⋅ E = 0
∇ ⋅ B = 0
Then, the first term on the right in the identity vanishes and the wave equations are obtained as presented below:
∂ 2 E ∂ t ² − c ∘ 2 ⋅ ∇ 2 E = 0 (13)
∂ 2 B ∂ t ² − c ∘ 2 ⋅ ∇ 2 B = 0 (14)
where C in Equation (15):
c ∘ = 1 μ ∘ ϵ ∘ = 2.99792458 × 10 8 m / s (15)
is the speed of light in free space.
Each of these radiations has both frequency and wavelength range called bands, and are expressed below [
The radial electric field surrounding such electron is given by the Equation (16) below:
E r = 1 4 π ε 0 ∗ e r 2 (16)
The condition stated by Equation (16) holds only for a stationary electron; but changes when such an electron is moving. Example: a current-carrying wire. The moving electron which produces current is also responsible for the magnetic field around it.
According to [
E θ = e ∗ 1 4 π ε 0 ∗ r ¨ sin θ c 2 r (17)
where E θ is the pulse of electromagnetic radiation, e is the electronic charge, r is the acceleration, c is the speed of light, r the distance from the nucleus, and the angle between the changing fields. The amount of radiation leaving the system also depends of the length of the current-carrying conductor and the wavelength of the current flowing through it. Base on this, electromagnetic radiation can be described as an energy that is transmitted in form of electromagnetic wave either through space or a material medium.
This is one of the major setbacks in the propagation of electromagnetic waves when it leaves its source. Researchers have shown that electromagnetic waves get attenuated as they travel outwardly. Attenuation can be referred to as a reduction in the intensity of propagated electromagnetic waves. Attenuation of electromagnetic radiation in space obeys the inverse-square law which indicates that power density reduces fairly rapidly with distance from the source. This means that signal attenuation, is proportional to the square of the distance travelled by the wave [
α E = 30 P t r 1 30 P t r 2 = 20 log r 1 r 2 (18)
where α E is the field intensity attenuation, P t the transmitted power, r 1 and r 2 are distances from the source of electromagnetic waves with r 2 greater than r 1 . This implies that at a distance of 2r from the source of the electromagnetic waves, the field intensity drops by 6 dB.
Propagating signals undergo modulation processes; such as amplitude, Frequency and phase modulation. The general form of an amplitude modulated wave is presented in Equation (19):
f ( t ) = A sin ( 2 π f c t ) + A m / 2 [ sin 2 π ( f c + f m ) t + ∅ ] + [ sin 2 π ( f c − f m ) t − ∅ ] (19)
where A and f c are the carrier amplitude and frequency, respectively. m is the modulation index, f m and ∅ are the frequency and phase of the baseband signal respectively. From the above equation, the modulation has three components which are the carrier wave and the two sidebands with frequencies above and below the carrier frequency [
f = f c ( 1 + k v m cos w m t ) (20)
where f c = carrier frequency, k = proportionality constant, v m cos = instantaneous modulating voltage. The modulation index of an FM signal is given in Equation (21):
m = Δ f f m (21)
where Δ f is the maximum deviation of the instantaneous frequency, and f m is the maximum frequency of the modulating signal.
Phase modulation PM is another form of angle modulation; besides FM where the phase of the carrier signal is varied by the modulating signal. In phase modulation, the variation in the carrier phase is proportional to the baseband signal, while its amplitude and frequency are constant during the process. The general form of a phase modulating wave is given as
v = A c sin ( w c t + m ( t ) + ∅ c ) (22)
where A c and w c are the amplitude and angular of the carrier signal respectively, m ( t ) is the modulating signal and ∅ c is the phase of the carrier signal being modulated.
[
The intensity or power of transmitted signal from a transmitting station received by an antenna at a different location is referred to as the electric field strength. Electric field strength is measured in dB millivolt per metre (dBmV/m) or dB microvolt per metre (dBuV/m). In 1998, Werner and Emders researched on an alternative means of calibration of electric field sensor which will enable a smooth computation of coupling errors which was not dealt with by previous methods of calibration like the use of closed transverse electromagnetic (TEM) wave. The new method involves the superposition of radiated and guided wave, and this presented an easy assessment of the coupling factor, a key index for computation of electric field strength, calibrations of sensors and antennas. Ajayi (2005) [
The intensity of radio wave leaving a transmitting station is found to differ in value at some locations away from the transmitter. This means that not all the intensity or signal strength that is transmitted by a station is being received at measured distances from the transmitter. Some percentages are lost in the propagation path. This drop in signal power as the radio wave propagates through space is known as path loss. A lot of factors are responsible for this phenomenon such as poor terrain and environment like the rural, sub-urban or urban areas, presence of hills, mountains, foliage etc and transmitter-antenna distance. Other factors include the height and location of antennas, diffractions and absorption of the electromagnetic waves. Path loss models on the other hand are experimented mathematical expressions used when illustrating radio wave propagation as a function of frequency, distance and some conditions. There are different models in existence for different conditions of the atmosphere, terrain, paths, obstructions, etc. The models for outdoor attenuations include:
1) Weissberger’s modified exponential model. It is a radio wave propagation model for predicting path loss by foliage. It has a frequency range of 230 MHz to 95 GHz with foliage depth of 400 m. It is a reviewed ITU (International Telecommunication Union) model for Exponential Decay (MED) created in 1982 [
Weissberger’s model is formally expressed as:
L = { 1.33 f 0.284 d 0.586 , if 14 < d ≤ 400 0.45 f 0.284 d , if 0 < d ≤ 14 (23)
where L = the loss due to foliage in decibel (dB); F = the transmission frequency gigahertz (GHz); d = the depth of foliage along the path in meters.
2) Early ITU model. It is also a radio propagation model for predicting loss due to foliage and was adopted in late 1986 [
L = 0.2 f 0.3 d 0.6 (24)
where f and d are defined as above; and L = path loss in dB; F = transmission frequency in megahertz (MHz); d = depth of the foliage.
3) Egli model: This is a model sourced from UHF and VHF television transmissions data in several large cities and suitable for cellular communication on irregular terrain. It predicts the path loss for outdoor line-of-sight transmissions and expressed as follows [
P R 50 = 0.668 G R G m [ h B h m d 2 ] 2 [ 40 f ] 2 P T (25)
where PR50 = 50th percentile receive power (W); PT = Transmit Power (W); GB = Absolute gain of the mobile station antenna; hB = Height of the base station antenna (m); hm = Height of the mobile station antenna (m); d = Distance from base station antenna (m); f = frequency of transmission (MHz).
4) ITU terrain model: This provides a method to predict the medium path loss for a telecommunication link and its prediction is based on the height of the path blockage [
A = 10 − 20 C N ( 37 ) ; C N = h F i ; h = h L − h o ; F 1 = 17.3 d 1 d 2 f d (26)
A = Additional loss (in excess of free − space loss) due to diffraction (dB); CN = Normalized terrain clearance; h = The height difference (negative in the case that the LOS path in completely obscured) (m); hL = Height of the line-of-sight link (m); ho = Height of the obstruction (m); F1 = Radius of the First Fresnel zone (m); d1 = Distance of obstruction from one terminal (m); d2 = Distance of obstruction from the other terminal (m); f = Frequency of transmission (GHz); d = Distance from transmitter to receiver (km).
5) Young model: It is an appropriate model for predicting path loss in cellular communications in large cities with tall structures. It has a frequency range of 150 MHz to 3700 MHz and it is expressed as presented in Equation (27) [
L = G B G m ( h B h m d 2 ) 2 β (27)
L = path loss in (dB); GB = gain of base transmitter (dB); Gm = gain of mobile transmitter (dB; hB = height of base station antenna (m); hm = height of mobile station antenna (m); d = line distance (Km); β = clutter factor.
6) Okumura model: This is used mostly in the cities where there are many urban structures, but not many tall blocking structures. It has a frequency range of 150 - 1920 MHz, a base station antenna height between 30 m and 1000 m and link distance between 1 Km and 100 km [
It is expressed as presented in Equation (28):
L = L F S L + A m u − H M G − H B G − ∑ K correction (28)
where L = The medium path loss (dB); LFSL = The free space loss (dB); Amu = Medium Attenuation (dB); HGM = Mobile station antenna height gain factor; HBG = Base station antenna height gain factor; Kcorrection = Correction factor gain (such as type of environment, water, surfaces, isolated obstacle etc.).
7) Hata model for urban areas: It is also referred as Okumura-Hata model and widely used radio frequency propagation model for predicting the behaviour of cellular transmissions in built up areas. It has a frequency range of 150 - 1500 MHz with mobile antenna height of 1 - 10 m, base station antenna height 30 - 200 m and link distance 1 - 10 km. It incorporates both suburban and open areas [
L u = 69.55 + 26.16 log 10 f − 1.82 log 10 h B − C h + [ 44.9 − 6.55 log 10 h B ] log 10 d (29)
for small or medium sized city
C H = 0.8 + ( 1.1 log 10 f − 0.7 ) h m − 1.56 log 10 f (30)
and large cities
C H = { 8.29 [ log 10 ( 1.54 h m ) ] 2 − 1.1 , if 150 ≤ f ≤ 200 3.2 [ log 10 ( 11.75 h m ) ] 2 − 4.97 , if 200 < f ≤ 1500 (31)
Lu = Path loss in urban areas (dB); hB = Height of base station antenna (m); hm = Height of mobile station antenna (m); f = Frequency of transmission (MHz); CH = Antenna height correction factor; d = Distance between the base and mobile stations (Km).
8) Hata model for open areas is presented in Equation (32) [
L o = L u − 4.78 ( log 10 f ) 2 + 18.53 log 10 f − 40.94 (32)
where Lo = Path loss in open area (dB); Lu = Path loss in urban areas for small sized city (dB); f = Frequency of transmission (MHz).
9) COST231 Extension to Hata Model: A model that is widely used for predicting path loss in mobile wireless system is the COST-231 Hata model [
L = 46.3 + 33.9 log f − 13.82 log h B − a ( h R ) + [ 44.9 − 6.55 log h B ] log d + c (33)
For suburban or rural environments:
( h R ) = ( 1.1 log f − 0.7 ) h R − ( 1.56 log f − 0.8 ) (34)
c = { 0 dB , for mediumcities and suburban areas 3 dB , for metropolitan areas
where, L = Median path loss. Unit: decibel (dB); f = Frequency of Transmission. Unit: megahertz (MHz); hB = Base station antenna effective height. Unit: meter (m); d = Link distance. Unit: Kilometer (km); hR = Mobile station antenna effective height. Unit: meter (m); a(hR) = Mobile station antenna height correction factor as described in the Hata model for urban areas.
[
Similarly, in Ondo State, the relationship between the line of sight and signal strength of an Ultra High Frequency (UHF) television signals was investigated. The Propagation curves for the signal along different routes were plotted and regression analysis was used to determine the exponential models which can be used to calculate signal strength for a given line of sight at the designated routes in the state [
According to Faruk, et al. (2009) [
A research in South-Eastern Nigeria by [
L p ( d ) = 75 + 31 log ( D ) (35)
where D is the ratio of the test distance (di) to the reference distance (d0).
And 75 dB is the path loss at the reference distance using the free-space model.
GSM signals operating on the frequencies of 900 MHz and 1800 MHz, which are the two frequencies used by mobile operators in Nigeria, were investigated in Enugu and Portharcourt. The mean square errors (μe) ranged from 0.8 dB to 5.04 dB for Okumura Hata at 900 MHz. For COST 231 Hata lied between 1 ≤ μ ≤ 15 dB which is universally accepted [
Measurement results of signal strength in UHF band obtained in Idanre Town of Ondo State Nigeria are presented and compared with the results predicted by using the propagation models. A modified COST231-Hata radiowave propagation model was developed and implemented with Matlab GUI (Graphical User Interface) for simulation. The model developed has 93.8% accuracy [
The free space earlier mention for wave propagation does not really exist, though it serves as a guide for simple computation of signal strength and path loss. Ideally there are obstacles in signal path which greatly influence the predictability of signal strength along any route. These obstacles include buildings, vegetations (foliage) hills.
The density of foliage and the heights of trees that are not uniformly distributed in a forested environment cause variation in the signal reception at different points. The research carried out in Ondo state on the effect of hills on UHF signal propagation showed a marked difference when measurements were taken at two different environments, one with without hills and the other with hills. The field strength decreases rapidly in region with hills [
Also, a study by [
Furthermore, to understand the degree of interaction, signal strength measurements of the 93.1 MHz frequency modulated Radio located at Federal University of Technology; Akure, Nigeria. The long rice irregular terrain model was used and the losses along the paths were determined. This was compared with the path loss predicted by the irregular terrain model and this was highly correlated. The result offered useful data for developing the contour map of the propagation loss which was developed for the station. It was concluded that with the irregular terrain model predictions can be used for accurate spectrum management in Nigeria [
This research was carried out in Akpabuyo Local Government Area, CRS, Nigeria; one of the few costal states in the Niger Delta region of Nigeria. The study area occupies 20,156 (7782 square miles) square kilometers with coordinates: 5˚45'N, 8˚30'E/5.750˚N, 8.500˚E. The state has a population of 3,737,517, with a population density of 190/Km2 (480/square miles). The area has distinct environmental characteristics that made Calabar Municipal Council, a challenging location to propagate electromagnetic waves; and therefore recipe for this study. Cross River State has a tropical-humid weather with wet and dry season. It also has an average temperature ranging between 15˚C - 30˚C; with an annual rainfall between 1300 - 3000 mm. This condition differs at the high altitude, Obudu plateau. The temperature at this altitude is between 4˚C - 10˚C. Cross River State has the largest tropically dense forest in Nigeria and in West Africa; which is about 0.85 million hectares containing 1000 square kilometres of mangrove and swamp forest. Its estuary is the largest in Nigeria with a low-energy, shallow coastal waters and shorelines.
These, distinct environmental characteristics made CRS a challenging location to propagate electromagnetic waves; and therefore recipe for this study.
It is radio frequency analyzer, with 24 channels spectrum, ranging between 46 - 870 MHz (model: RO.VE.R.-“DLM3-T”). It has a video display screen and corresponding output sound to capture signals from terrestrial radio stations and television stations. CATV measures signal of both radio and TV in dB, dBμV and dBmV. The equipment works perfectly with 12 V supply, either from an external battery, or from other available grid supply; and it’s capable of powering the pre-amplifier of an antenna system for maximum reception.
An outside television antenna of dimension 59(L) × 8.5(W) × 11(H) cm on a pole of about 7 m, was used to receive the signal at different locations across the state. Its frequency range spans from 40 - 860 MHz, from channel 1 to channel 69. The antenna has both VHF and UHF gain of 20 ± 3 dB, with an impedance of 75Ω and a noise coefficient less than 3 dB. The operational power of this antenna is 3 W with an output level of 145 dB.
GPS 72H from Garmin was used to measure the distance from the transmitting antennas to different measuring locations in the state as well as their elevations above sea level.
Measurements were carried out in all the Local Government Areas in the state along motor-able and accessible route. Field or signal strength at various locations were examined both at the UHF and VHF bands, with special attention given to some reliefs along the measuring route. This was made possible by large contour map of the state. At each location, the signal strength of various stations alongside the elevation above sea level and coordinates in northings and eastings were measured. Measurements of the signal strength were measured first at premises of the stations; also referred to as the near field signal, before subsequent measurements at other locations.
Statistics | Field Data | Cost231Hata | Egli | Okuruma | Free Space |
---|---|---|---|---|---|
Min | 47.7 | 87.52 | 58.27 | 147.2 | 285.7 |
Max | 82.6 | 99.73 | 66.27 | 152.9 | 289.7 |
Mean | 66.08 | 93.96 | 62.49 | 150.2 | 287.8 |
Median | 66.2 | 94.51 | 62.85 | 150.5 | 288 |
Mode | 47.7 | 87.52 | 58.27 | 147.2 | 285.7 |
Std | 8.173 | 3.365 | 2.205 | 1.584 | 1.102 |
Statistics | Field Data | Cost231Hata | Egli | Okuruma | Free Space |
---|---|---|---|---|---|
Min | 40.7 | 110.2 | 33.95 | 159.2 | 303.6 |
Max | 43.1 | 116.2 | 37.86 | 164.9 | 305.5 |
Mean | 41.94 | 113.2 | 35.92 | 162.2 | 304.6 |
Median | 42 | 113.2 | 35.9 | 162.4 | 304.5 |
Mode | 42.1 | 110.2 | 33.95 | 159.2 | 303.6 |
Std | 0.5384 | 1.617 | 1.058 | 1.579 | 0.5288 |
Measurements taken from Akpabuyo L.G.A. showed the following results: the signal strength received from VHF Channel 11 ranged from 20 dBμV to 49 dBμV. From recorded empirical statistics from the study, 50% of the area received signal from this station above 30 dBμV, while other regions have signals below this value; representing the fringe zone of the frequency. The Egli model strongly agreed with the calculated path loss from the field data as shown in the figure. Poor signal in this area could be attributed to obstructions along the propagation path since the signal must pass through Calabar city located along the line of sight of the signal before getting to residents in Akpabuyo Local Government Area.
There was no video traffic at all from Channels 27 and 45 in this area; although the study recorded a steady fluctuation between 17 dBμV and 19 dBμV from both propagating stations. This means that the signal completely faded off before getting to residents of this area; as the transmitter was monitored and confirmed not to be off.
The Cross River State Broadcasting Corporation (CRBC) television, transmitting at Channel 11, of frequency 219.25 MHz, has its near field signal strength coverage in some parts of Akpabuyo Local Government Area. Minority of the residents in this part of the rural location fell within the secondary coverage zone, while others were in the fringe zone. The calculated path loss, when compared with standard path loss models in areas where there was signal, closely agreed with predictions indicated in Egli’s model; in terms of path loss prediction. Channel 27 signal, at 519 MHz, has very scanty signal in many parts of Akpabuyo Local Government Area. It is interesting to note that residents in this area depend only on other Nigerian national electronic media to receive information; including news relating to the state they reside in.
Channel 27 signal at 519 MHz, has very weak signal coverage in Akpabuyo Local Government Area; with signal strength below to 50 dB. Also, Egli’s model closely agreed with the calculated path loss in the regions where this signal was received. Furthermore, AKBC channel 45 signal from Uyo was scanty received. Received signal strength dropped to as low as 13 dB in many parts of the rural area. Egli’s model was the only path-loss model that closely predicted the path loss at this frequency in this rural setting. Details are as presented in Figures 8-15 and
Terrestrial broadcasting, as monitored by this study, on the coverage of one of the Local Government Area (Akpabuyo Local Government Area), using one spot transmission out-let is unachievable. This is predicated on the fact that the state’s topography is naturally undulating; thus, affecting the smooth travelling of electromagnetic signals. The state’s broadcasting stations, both at UHF and VHF channels do not transmit successfully across this densely forest (rural) setting. The state, therefore, is poorly covered in terms of television signal. Remedial measures such as installing Repeater stations at different locations as signal booster are strongly recommended.
The authors declare no conflicts of interest regarding the publication of this paper.
Bassey, D.E., Effiong, G.O., Omini, O.U. and Obisung, E.O. (2019) Empirical Studies on Topographical Influences on Crbc/Akbc Terrestrial Television Stations’ Signals in Akpabuyo Local Council Area, Nigeria. Journal of Computer and Communications, 7, 50-71. https://doi.org/10.4236/jcc.2019.79005