^{1}

^{2}

Generally, mine roads are located in the mountain areas, as its complex topography, mostly along the river near the cliffs, steep bend anxious, the mine road design has to adopt lower technical standards relatively and usually is lack of traffic safety facilities. Especially, there are mainly medium-sized vehicles on mine road, under the heavy traffic vehicles affect repeatedly, high frequency of traffic accidents more easily happen in mine road area and cause serious effects on life or property. Combining with the particularity of mine road safety environment, this paper studies the basic theory of safety evaluation, analyses the factors of traffic safety design and special mine terrain conditions, and then establishes mine road safety index system and evaluation model based on the principles such as systematicness, independent indexes, qualitative and quantitative analysis, feasibility, scientificity and reliability. At last, the paper successfully evaluates the safety of road in Huang Mailing phosphate rock area with fuzzy AHP method based on engineering project.

Usually mine road is located in mountain areas with low technical design standards winding along complex topography, mostly near river or cliffs, or steep bend anxious. And generally as it is used as a temporary road which paved with gravel and lack of traffic safety facilities, it causes heavy dust, large damage, poor conditions and large maintenance [

In order to ensure highway traffic safety, traffic scholars do a lot of researches on the causes of traffic accidents and the factors, factors cause accidents as high- way alignment design, traffic safety facilities, drivers, etc. The main cause of the accident is due to the driver’s fault (up to 87%), which is considered to be the key of the road alignment conditions, traffic conditions and other factors in the accident. In fact, this is not reasonable, it will make the road workers take full responsibility attributed to others, and when design road, in order to reduce the cost and benefit, the consequences of doing so cannot guarantee the safety of road traffic ( [

Safety evaluation is to use system engineering theory to identify and analyze the existence of risk factors, including the identification of risk factors and the degree of hazard assessment. The safety evaluation contents are shown in

In engineering practice, the two factors of risk degree and risk factor are closely related. According to the safety accidents distribution of mine road and cause analysis, the paper mainly studies from the following two aspects:

1) Hazard identify

Source of hazard: to confirm that there are no new hazard sources, and the change of danger.

Quantify risk: probability of risk.

2) Hazard degree assessment

Identify indexes and establish the value of danger.

Hazard control.

Safety evaluation flow diagram includes preliminary preparation, hazard identification and analysis, qualitative and quantitative analysis, safety measures and safety summary, the analysis flow diagram is shown in

Fuzzy comprehensive evaluation is based on the evaluation criteria and the measured values. It is a method to evaluate the influence of many factors of the things or phenomena after the fuzzy transformation. There are

Compared with other highways, mine road has its unique characteristics. In order to meet the general highway design, it must meet its special requirements. The basic principles for the safety evaluation system of the mine road are mainly in the following five aspects ( [

1) Systematic principle

Mine road is a complicated system closely relates to many factors as highway safety and highway alignment, pavement quality, line of sight, sign and marking, topography, traffic and etc. Therefore, it is needed to consider the overall analysis of the system of the highway safety status of the mine by the evaluation index system of the evaluation index system.

2) Independent indexes

Indexes are an important factor that can truly reflect the safety degree. When selecting the indexes, it must be ensured that they are independence in the same level, do not allow evaluating the same or similar content with multiple indexes.

3) The combination of qualitative and quantitative

It will be more favorable to make a comprehensive analysis for highway traffic safety combining with the qualitative and quantitative methods.

4) The principle of feasibility

In order to ensure the evaluation system can be implemented, the indexes are

chosen following the practical principles. According to the relevant files and field data collection, it is preliminary evaluated the feasibility of this safety index system to ensure the evaluation successfully.

5) The principles of science and reliability

In order to improve the management level of highway safety operation and ensure the realization of the overall goal of highway construction, it is necessary to evaluate the safety of highway alignment design and safety facilities. It is an important part of achieving this goal to ensure the scientific and reliability of indexes.

This paper establishes traffic safety evaluation system of mine road according to the above five principles and meets both the primary and secondary factors and all possible factors. The index system is as follows.

1) First-level indexes

They are the highest level factors for safety evaluation, including the external environmental indexes U1, safety facilities management indexes U2, technical safety indexes U3, and each of them has its own sub-indexes.

2) Second-level indexes

Second-level indexes are established on the further classification of primary indexes. They include topography U_{11}, climate U_{12} and traffic volume U_{13}, pedestrian and other interference factorsU_{14}; lighting U_{21}, guardrail U_{22}, marker U_{23}, marking U_{24} and other aspects of security management U_{25}; sight distance U_{31}, subgrade and pavement performance U_{32} and road alignment U_{33}. The evaluation system framework is shown in

The main factors of mine road accidents include vehicle performance, driver, traffic condition, management and maintenance and environment based on the investigation of the existing highway safety. Of which the driver is the most important factor for traffic accidents. In this paper, the design of safety is mainly from the road alignment, protective facilities, operating environment and other aspects to optimize ( [

1) Establish appropriate hierarchical structure

Hierarchical structure is shown as

2) Establish the corresponding comparison matrix at each level. Assume the first level of element

3) Using the root square method to determine the weight. The steps of the method are as follows:

a) Calculate the product

Serial number | Important hierarchy | |
---|---|---|

1 | Both elements | 1 |

2 | Of the two elements | 3 |

3 | Of the two elements | 5 |

4 | Of the two elements | 7 |

5 | Of the two elements | 9 |

6 | Of the two elements | 1/3 |

7 | Of the two elements | 1/5 |

8 | Of the two elements | 1/7 |

9 | Of the two elements | 1/9 |

Notes: when

b) Calculate the n-th root

c) Normalize the vector of

The vector

d) Calculate the largest eigenvalue

For any

4) Carry out a single sorting, and do the consistency test. The formula for consistency indexes of judgment matrix is as following：

5) Using the single level sorting results to test the results of the total sorting. These two steps are carried out from the highest level to the lowest level, and the random consistency ratio is calculated as following：

Among them, the average random consistency index

When CR (k) < 0.1, it is good for the overall consistency of the judgment matrix and can be acceptable, otherwise, it needs to revise the judgment matrix until it meets the requirements.

1) Earthquake intensity and magnitude

The seismic fortification intensity is 6 degrees in the mining area and the nearby area, and the basic seismic acceleration is 0.05 g. The crust is relatively stable.

2) Environment geology condition

a) Slope stability: structure surface of slope bedding is well developed. Rock soil generally contains manganese carbonaceous schist, carbon slices rock and

Order | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
---|---|---|---|---|---|---|---|---|---|

RI | 0 | 0 | 0.59 | 0.91 | 1.12 | 1.24 | 1.33 | 1.41 | 1.43 |

green schist soft inter layer, and rock of slope is along the slope, so the slope is easy instability when there appears large rainfall or obvious blasting vibration.

b) Landslide: because of very low mechanical strength and the small permeability coefficient of rock in mining area, when water immerges, the rock is easy to soften in the effect of gravity and some external factors, which may lead to mountain cracking, collapse, landslide and collapse.

c) Debris flow: there has accumulated about 22,028 thousand cubic meters waste rock, slag and tailings after over thirty years mined of mines. On the one hand, accumulation saturated by heavy rain will lose self-stability and causes creeping, this is a certain threat to the stability of slopes and natural drainage channels; on the other hand, surface water and mine water has a certain erosion effect. These two factors can easily cause geological disasters of debris flow.

d) Water resources and water environment: On the one hand, groundwater resource is dried up gradually because of the mine water drains out when mining. On the other hand, lixiviation water of phosphate rock contents of S ion, turbidity, suspended solids which exceed the standard, when it is drained with the mine water, it will pollutes the wild goose River and Huan water certainly nearby. Such will influence life water and agricultural live of nearby residents.

e) Land resources: the existing opencast pits, waste rocks and slag accumulation destroy and occupy part of the slope, accounting to 10% of the mining area. In the future of the mining process, waste rock, slag accumulation and mine water discharge will damage environmental and geological problems further.

f) Dust: A large number of mud, silt sand and harmful sulfur dust are produced during the process of mining, handling and transportation ore. These are very harmful for the mine workers and the environment around.

3) Geological environment impact assessment and type

Landslide is the main geo-environment problem of mining rock because of the development of mine geological environment. Local area may occur rock fall and mudslides may also occur as mine waste rock and slag stacking area, height, angle of steep slope in rainstorm. The exposed ore bodies have great influence on the surface structure, highway, underground water environment and natural landscape destruction, and the damage will be further increased after the underground mining in the future. Overall, the environmental geological conditions of the mining area is a complex type.

The formation lithology of the mining area is more complex, which is composed of solid and semi strong rocks, locally distributes unstable rock groups, and the engineering geological condition is of middle complex. The mining area appears a typical low hilly terrain, the overall scenery changes with mountain stretch and gully crossing landform. The new cement concrete pavement is 6 m wide and 1029 m long for secondary road, 4 m wide and 139 m long for access road. According to the characteristics, site conditions, technical data and experts opinion, the paper analyses the 1 ~ 9 judgment matrix shown in _{0} judgment matrix as shown in

U - U_{0} hierarchy judgment matrix related parameters are calculated as follows：

1) Calculate the geometric average value of all elements of the U - U_{0} hierarchy judgment matrix:

2) Normalized calculation, then obtained the following:

3) Calculate the maximum eigenvalue

From

Therefore, the U - U_{0} judgment matrix meets the requirements of consistency verification.

Similarly, establishment U_{1} - U_{00} judgment matrix, as shown in

U | U_{1} | U_{2} | U_{3} |
---|---|---|---|

U_{1} | 1 | 1/3 | 1/7 |

U_{2} | 3 | 1 | 1/5 |

U_{3} | 7 | 5 | 1 |

U_{1} | U_{11} | U_{12} | U_{13} | U_{14} |
---|---|---|---|---|

U_{11} | 1 | 3 | 5 | 7 |

U_{12} | 1/3 | 1 | 4 | 6 |

U_{13} | 1/5 | 1/4 | 1 | 5 |

U_{14} | 1/7 | 1/6 | 1/5 | 1 |

1) Calculate the geometric average value of all elements of the U_{1} - U_{00} hierarchy judgment matrix:

2) Normalized calculation, then obtained the following:

3) Calculate the maximum eigenvalue

From

Therefore, the U_{1} - U_{00} judgment matrix meets the requirements of consistency verification.

Similarly, establishment U_{2} - U_{00} judgment matrix, as shown in

1) Calculate the geometric average value of all elements of the U_{2} - U_{00} hierarchy judgment matrix

2) Normalized calculation, then obtained the following:

3) Calculate the maximum eigenvalue

From

Therefore, the U_{2} - U_{00} judgment matrix meets the requirements of consistency verification.

Similarly, establishment U_{3} - U_{00} judgment matrix, as shown in

U_{3} - U_{00} hierarchy judgment matrix related parameters are calculated as follows：

1) Calculate the geometric average value of all elements of the U_{3} - U_{00} hierarchy judgment matrix：

U_{2} | U_{21} | U_{22} | U_{23} | U_{24} | U_{25} |
---|---|---|---|---|---|

U_{21} | 1 | 1/4 | 1/2 | 1/3 | 5 |

U_{22} | 4 | 1 | 3 | 5 | 7 |

U_{23} | 2 | 1/3 | 1 | 1/3 | 1/2 |

U_{24} | 3 | 1/5 | 3 | 1 | 2 |

U_{25} | 1/5 | 1/7 | 1/3 | 1/2 | 1 |

U_{3} | U_{31} | U_{32} | U_{33} |
---|---|---|---|

U_{31} | 1 | 1/2 | 1/5 |

U_{32} | 2 | 1 | 1/3 |

U_{33} | 5 | 3 | 1 |

2) Normalized and obtained the following:

3) Calculate the maximum eigenvalue

From above, we can get

Therefore, the U_{3} - U_{00} judgment matrix meets the requirements of consistency verification.

According to the principle of AHP, we can reduce each index weight of the mine road safety evaluation system in the whole weight of the safety evaluation system, as shown in

Checking consistency:

According to the weight value of each indexes in _{1}, safety facilities management U_{2} and technical security U_{3} are respectively 0.101, 0.236 and 0.663, which indicates that the technical security is the biggest impact on mine road safety.

After analyzing the first level indexes, the paper finds the terrain and landforms index weight that takes over half is 0.547 in the environment safety index U_{1}. So for this project, the terrain and landforms has the largest effect of mine road. The secondary indexes of lightings U_{21}, guardrails U_{22}, signs U_{23}, markings U_{24} and other safety facilities U_{25} are value 0.115, 0.527, 0.101, 0.203 and 0.054 respectively in the management index U_{2}. Thus, for the mine road mainly with truck vehicles, guardrail is the main safety factor of index U_{2}. In Technology security U_{3}, sight distance, pavement performance and alignment are 0.122, 0.230 and 0.648 weight respectively. Considering all above values, we concludes again

U | U_{1} | U_{2} | U_{3} | W |
---|---|---|---|---|

0.101 | 0.236 | 0.663 | ||

U_{11} | 0.547 | 0 | 0 | 0.182 |

U_{12} | 0.287 | 0 | 0 | 0.096 |

U_{13} | 0.121 | 0 | 0 | 0.040 |

U_{14} | 0.0449 | 0 | 0 | 0.015 |

U_{21} | 0 | 0.115 | 0 | 0.038 |

U_{22} | 0 | 0.527 | 0 | 0.176 |

U_{23} | 0 | 0.101 | 0 | 0.034 |

U_{24} | 0 | 0.203 | 0 | 0.068 |

U_{25} | 0 | 0.0540 | 0 | 0.018 |

U_{31} | 0 | 0 | 0.122 | 0.041 |

U_{32} | 0 | 0 | 0.230 | 0.077 |

U_{33} | 0 | 0 | 0.648 | 0.216 |

C_{ij} | 0.088 | 0.0995 | 0.002 | |

R_{ij} | 0.90 | 1.12 | 0.58 |

that alignment design is the most important factor in road safety design, so when layout alignment and select design indexes, we should consider detail for different schemes and do a good safety protect measures.

The safety evaluation index of the mine road meet the consistency requirements by using the fuzzy comprehensive evaluation indexes to calculate and analyze.

In this paper, the fuzzy comprehensive evaluation method is used to evaluate the safety of mine road, and the main study results are concluded as following:

1) According to the safety particularity of mine road, based on the analysis and evaluation theory, the paper studies the safety evaluation process of mine road.

2) This paper establishes the evaluation index system of mine road safety based on the principle of system, independence, qualitative and quantitative analysis, feasibility, scientificity and reliability. It includes three first-level indexes as environment, safety management, and safety technology and 12 second level indexes.

3) Using the fuzzy analytic hierarchy process to evaluate the safety of mine road, the results show that the external environment index U1, safety facilities management U_{2}, and security technology U_{3} are value 0.101, 0.236 and 0.663 respectively. Because of more difficult technical problem of mine road and higher design requirement, the designs of horizontal and longitudinal alignment, and cross section, pavement performance indexes occupy the maximum proportion, technical conditions is the largest impact factor for mine road safety.

The authors would like to thank Mr. Li Feng of Changsha Design and Research Institute of Chemical Industry Ministry who provides assistance in collecting engineering project data.

Qin, C.H. and Zhang, Y.X. (2017) Evaluation the Safety of Mine Road Based on Fuzzy Analytic Hierarchy Process. Journal of Transportation Technologies, 7, 70-82. http://dx.doi.org/10.4236/jtts.2017.71005