Evaluation of Characteristics of Interfacial Phases Produced in Al/Ni3Al Composite during Manufacturing
Seyed Abdolkarim Sajjadi, Maryam Abbasi, Mazyar Azadbeh
DOI: 10.4236/msa.2011.29182   PDF    HTML     4,691 Downloads   8,603 Views   Citations


Metal matrix composites (MMCs) are currently being investigated because of their superior properties. The properties are mainly attributed to the efficiency of the load transfer from the matrix to the reinforcements through the matrix-reinforcement interface. The aim of this study is to investigate the effect of manufacturing parameters on the microstructure and morphology of the interface and the aluminide phases formed at the matrix-reinforcement interfaces. The parameters are: milling time to fabricate Ni3Al, method of mixing of Ni3Al and Al powders, compaction pressure and sintering temperature. The composite studied in this research was Al/5 Vol% Ni3Al made from two different types of Ni3Al powders. The results showed that compacting and sintering at higher levels lead to the transformation of Ni3Al particles to thin layers of Al3Ni. It was also shown that the prolonged milling time to produceNi3Alreinforcements and the prolonged ball milling procedure for mixing the powders, both, promote the diffusion process at reinforcement/matrix interface.

Share and Cite:

S. Sajjadi, M. Abbasi and M. Azadbeh, "Evaluation of Characteristics of Interfacial Phases Produced in Al/Ni3Al Composite during Manufacturing," Materials Sciences and Applications, Vol. 2 No. 9, 2011, pp. 1340-1348. doi: 10.4236/msa.2011.29182.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] F. Velasco, C. E. DA Costa, B. Rodero, C. Santamarta and J. M. Torralba, “Intergranular Corrosion Resistance of Fe3Al/2014 Al Particulate MMC,” Journal of Mate- rials Science Letters, Vol. 19, 2000, pp. 61-63. doi:10.1023/A:1006708000114
[2] M. Adamiak, J. B. Fogagnolo, E. M. Ruiz-Navas, L. A. Dobrza?ski and J. M. Torralba, “Mechanically Milled AA6061/(Ti3Al)P MMC Reinforced with Intermetallics—The Structure and Properties,” Journal of Materials Processing Technology, Vol. 155-156, 2004, pp. 2002- 2006. doi:10.1016/j.jmatprotec.2004.04.202
[3] B. Torres, M. Lieblich, J. Ibanez and A. G. Escorial, “Mechanical Properties of Some PM Aluminide and Silicide Reinforced 2124 Aluminium Matrix Compo- sites,” Scripta Materialia, Vol. 47, No. 1, 2002, pp. 45-49. doi:10.1016/S1359-6462(02)00095-7
[4] J. M. Torralba, F. Velasco, C. E. DA Costa, I. Vergara and D. Caceres, “Mechanical Behaviour of the Interphase between Matrix and Reinforcement of Al 2014 Matrix Composites Reinforced with (Ni3Al)p,” Composites Part A, Vol. 33, No. 3, 2002, pp. 427-434.
[5] F. Velasco, C. E. DA Costa, N. Candela and J. M. Torralba, “Fracture Analysis of Aluminium Matrix Com- posite Materials Reinforced with (Ni3Al)p,” Journal of Materials Science, Vol. 38, No. 3, 2003, pp. 521-525. doi:10.1023/A:1021884001846
[6] C. Diaz, J. L. Gonzalez-Carrasco, G. Caruana and M. Lieblich, “Ni3Al Intermetallic Particles as Wear-Resistant for AI-Base Composites Processed by Powder Reinfor- cement Metallurgy,” Metallurgical and Materials Trans- action A, Vol. 27, 1996, pp. 3259-3266.
[7] P. B. DA Silva-Maia, F. Velasco, N. Anton, C. E. DA Costa and W. C. Zapata, “Corrosion Resistance of 2014 Aluminium Matrix Composites Reinforced with Ato- mised Ni3Al,” Advanced Performance Materials, Vol. 6, No. 2, 1999, pp. 117-127. doi:10.1023/A:1008713425137
[8] J. B. Fogagnolo, F. Velasco, M. H. Robert and J. M. Torralba, “Effect of Mechanical Alloying on the Mor- phology, Microstructure and Properties of Aluminium Matrix Composite Powders,” Materials Science and Engineering, Vol. 342, 2003, pp. 131-143. doi:10.1016/S0921-5093(02)00246-0
[9] M. D. Berm′udez, F. J. Carri′on, P. Iglesias, G. Mart′ynez-Nicol′as, E. J. Herrera and J. A. Rodr′yguezb, “Influence of Milling Conditions on the Wear Resistance of Mechanically Alloyed Aluminium,” Wear, Vol. 258, No. 5-6, 2005, pp. 906-914.
[10] I. Ozdemir, S. Ahrens, S. M. Ucklich and B. Wielageb, “Nanocrystalline Al-Al2O3p and SiCp Composites Produced by High-Energy Ball Milling,” Journal of Materials Processing Technology, Vol. 205, No. 1-3, 2008, pp. 111-118. doi:10.1016/j.jmatprotec.2007.11.085
[11] C. Suryanarayana, “Mechanical Alloying and Milling,” Progress in Materials Science, Vol. 46, No. 1-2, 2001, pp. 1-184. doi:10.1016/S0079-6425(99)00010-9
[12] Y. B. Liu, S. C. Lim, L. Lu and M. O. Lai, “Recent Development in the Fabrication of Metal Matrix- Particulate Composites Using Powder Metallurgy Techniques,” Journal of Materials Science, Vol. 29, 1994, pp. 1999- 2007. doi:10.1007/BF01154673
[13] Z. Razavi Hesabi, H. R. Hafizpour and A. Simchi, “An Investigation on the Compressibility of Aluminum/Nano- Alumina Composite Powder Prepared by Blending and Mechanical Milling,” Materials Science and Engineering A, Vol. 454-455, 2007, pp. 89-98. doi:10.1016/j.msea.2006.11.129
[14] J. B. Fogagnolo, E. M. Ruiz-Navas, M. H. Robert and J. M. Torralba, “The Effects of Mechanical Alloying on the Compressibility of Aluminium Matrix Composite Pow- der,” Materials Science and Engineering A, Vol. 355, No. 1, 2003, pp. 50-55. doi:10.1016/S0921-5093(03)00057-1
[15] S. Okuma, “The Sintering Mechanism of Aluminum and the Anodyzation of Aluminum Sintered Bodies,” Electro- component Science and Technology, Vol. 6, No. 1, 1979, pp. 23-29.
[16] J. Cintas, J. M. Montes, F. G. Cuevas, E. J. Herrera, “Influence of Milling Media on the Microstructure and Mechanical Properties of Mechanically Milled and Sintered Aluminium,” Journal of Materials Science, Vol. 40, No. 15, 2005, pp. 3911-3915. doi:10.1007/s10853-005-0756-y
[17] J. Cintas, F. G. Cuevas, J. M. Montes and E. J. Herrera, “Microstructural Control of Sintered Mechanically Alloyed Al-1%Ni Material,” Scripta Materialia, Vol. 52, No. 5, 2005, pp. 341-345. doi:10.1016/j.scriptamat.2004.11.001
[18] M. Azadbeh and M. Abbasi, “Effect of Manufacturing Parameters on Phase Growth and Homogenization of a PM Al/Ni3AL Composite,” Proceedings 5th International Powder Metallurgy Conference, Ankara, October 2008.
[19] S. Kumaran, B. Chantaiah and T. Srinivasa Rao, “Effect of Niobium and Aluminium Additions in TiAl Prealloyed Powders during High-Energy Ball Milling,” Matererials Chemical Physics, Vol. 108, 2008, pp. 97-101.
[20] M. Lieblich, J. L. Gonzalea-Carrasco and F. Garcia-Cano, “Asymmetrical Phase Growth in a PM Al/Ni3Al Composite,” Journal of Materials Science Letters, Vol. 18, 1999, pp. 905-908. doi:10.1023/A:1006668815274
[21] L. Lu, M. D. Lap and S. Zhang, “Fabrication of Ni3AI Intermetailic Compound Using Mechanical Alloying Technique,” Journal of Materials Processing Technology, Vol. 48, No. 1, 1995, pp. 683-690. doi:10.1016/0924-0136(94)01709-A

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.