C@Ag/TiO2: A Highly Efficient and Stable Photocatalyst Active under Visible Light

Abstract

In this paper, preparation and characterization of C@Ag/TiO2 nanospheres compound photocatalysts was reported. C@Ag nanosphere was firstly synthesized via hydrothermal reaction, and followed by a sol-gel process to obtain the functionalized C@Ag/TiO2 nanosphere which has highly efficient visible light catalytic ability towards methyl orange (MO). The morphology of the obtained compound was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) technologies. From which we can see that the as-prepared samples show a spherical structure with a diameter of approximately 200 nm, and the silver particle in core was about 10 nm. The catalytic ability of the synthesized photocatalysts under visible light irradiation shows that C@Ag/TiO2 possesses higher photocatalytic activity towards MO degradation than that of N-P25 (TiO2). Furthermore, the C@Ag/TiO2 photocatalysts exhibited excellent reusability with almost no change after five runs. Finally, the possible photocatalytic mechanism of catalyst under visible light was discussion and proposed.

Share and Cite:

Jin, B. , Zhou, X. , Xu, X. , Ma, L. , Wu, Z. and Huang, Y. (2013) C@Ag/TiO2: A Highly Efficient and Stable Photocatalyst Active under Visible Light. World Journal of Nano Science and Engineering, 3, 1-5. doi: 10.4236/wjnse.2013.31001.

1. Introduction

The photocatalysis technique has a promising application prospect in pollutant decomposition and hydrogen evolution via the generation of •OH radicals and other oxidative species [1-3]. The semiconductor TiO2 is considered as one of the best photocatalysts. However, the light response range and the photo-efficiency of TiO2 are limited because of its wide band gap (3.2 eV) [4,5]. Therefore, the creation of simple, efficient, and sustainable photocatalysts that work well with visible light is a major challenge in this research field [6-8]. Until now, several methods have been reported to improve the photo-catalyzed efficiency of TiO2. Among them, surface modification via the addition of metals which can enhance the photocatalytic activities is widely studied, and many metals, such as Pd, Pt, Rh, Ru, Ag, have been investigated to extent the absorption wavelength of noblemetal/TiO2 compounds into the visible region [9-14]. The reason is that deposition of metals on the surface of TiO2 would produce traps to capture the photo-induced electrons or holes, leading to the reduction of electronhole recombination and thus improving the photocatalytic efficiency [15]. Because of non-toxic, relatively inexpensive and obvious modification effect, loading Ag to improve the TiO2 catalytic activity has been raised extensive attention. However, a problem is that Ag nanoparticles, which are chemically very reactive, would be easily oxidized when directly contact with TiO2. Romanyuk et al. confirmed that Ag could have been oxidized at the Ag-TiO2 interface to form eventually a 10 nm thick layer of silver oxide (AgO) at room temperature by employing time-of-flight secondary ion mass spectroscopy [16]. To prevent this oxidation, a passive material, such as SiO2, must be coated on the surface of Ag nanoparticles so as to separate them from TiO2. Zhang et al. reported core/shell nanofibers of TiO2@carbon embedded by Ag nanoparticles with well-dispersed distribution of small Ag NPs in the carbon layer [17]. However, as the near-field amplitude decays in a rough estimation exponentially with the distance from the nanoparticles surface, the protection layer has to be kept sufficiently thin [18].

In this paper, we prepared C@Ag nanospheres by a simple hydrothermal method, and then using the sol-gel, C@Ag/TiO2 composite visible light catalyst was synthesized. MO was used simulation pollutant, and the degradation experiments of the photocatalysts were carried out under visible light. The results showed the photocatalytic activity of the C@Ag/TiO2 composite is 3 times higher than that of N-P25. Moreover, stability test showed that the composite photocatalyst is almost inactivating even after five cycles and the good stability is due to the protective effect of the coated carbon layers.

2. Experimental Section

2.1. Preparation of the Catalysts

A solution of AgNO3 (1 mL, 0.02 M) was added to a glucose solution (40 mL, 0.5 M) with stirring to form clear solutions, which was placed in a 50 mL Teflonsealed autoclave and maintained at 180˚C for 12 h [19]. The precipitate was collected and washed with distilled water and absolute alcohol three times, respectively, and oven-dried at 80˚C for 24 h.

Ti[OCH(CH3)2]4 (3 mL, Aldrich, 97%) and isopropyl alcohol (40 ml) mixed solution added dropwise to a solution of HNO3 (50 ml, pH = 1.0) containing an amount of C@Ag, after aged for 10 h at room temperature, and then  dried at 110˚C for 20 h. The resultant gel was calcined at 500˚C for 2 h under a nitrogen atmosphere, which was denoted as CAT-X (X denotes percentage content of C@Ag).

2.2. Characterization of the Catalysts

The surface morphology was examined by a scanning electron microscopy (LEO1530VP, LEO), and a transmission electron microscopy (JEOL, JEM2010). UV-Vis diffuse reflection absorption spectra (UV-Vis/DRS) of the samples were recorded by an UV-Vis spectrometer (U3010, Hitachi) equipped with an integrating sphere accessory in the diffuse reflectance mode (R) and BaSO4 as a reference material. The chemical nature of C, Ag, Ti, O have been studied by X-ray photoelectron spectroscopy (XPS) in Krato Axis Ultra DLD spectrometer with Al Ka X-ray (hv = 1486.6 eV) at 15 kV and 150 W. The binding energy was referenced to C 1s line at 284.6 eV for calibration.

2.3. Photocatalyst Reaction

The photocatalytic reaction was conducted in the XPA-II photochemical reactor (Nanjing Xujiang Machine-electronic Plant). A 500 W Xe lamp was used as the simulated solar light source, and a house-made filter was mounted on the lamp to eliminate infrared irradiation. MO (20 mg/L) was used as contamination [12]. 20 mg photocatalyst powder was dispersed in 200 mL reaction solutions by ultrasonicating for 15 min, then the suspension was magnetically stirred in dark for 1 h. Air was blown into the reaction medium at a flow rate of 200 mL/min during the photocatalytic reaction. One 8 mL of the suspension was sampled and filtered. The concentration of the remaining MO was measured by a Hitachi UV-3010 spectrophotometer. The degradation ratio was calculated by X = (A0 − A)/A0 × 100%.

3. Results and Discussion

3.1. Morphology and Structures of the Samples

The morphology of the C@Ag/TiO2 sample is examined by SEM and TEM, and the images are shown in Figure 1. From SEM image, it is clear that C@Ag/TiO2 is composed of many monodispersed spherical particles with a diameter of about 200 nm (shown in Figure 1(a)). The spheres are relatively uniform with very smooth surface. Figure 1(b) is a TEM image of C@Ag/TiO2 sample and the samples shows spherical particles morphology. The diameters are approximately 200 nm, which is in agreement with the result of SEM. It is interesting that the middle of Ag nucleus can clearly be seen after magnified (shown in Figure 1(b) inset). A diameter is approximately 10 nm. The energy dispersive spectroscopic (EDS) analysis (Figure 1(c)) of the C@Ag/TiO2 sample reveals the existence of C, Ag, O, and Ti elements. The element content of C, Ag, O, and Ti in the compounds investigated with the results of EDX is 5.35, 0.20, 31.55, 62.90 at%, respectively. It reveals that the samples were consists of C, Ag and TiO2.

Figure 2 displays the XRD patterns of the prepared C@Ag and C@Ag/TiO2 samples. Figures 2(a) exhibits the characteristic diffraction peaks of Ag (JCPDS file No.

Conflicts of Interest

The authors declare no conflicts of interest.

References

[1] M. Shang, W. Z. Wang, S. M. Sun, J. Ren, L. Zhou and L. Zhang, “Efficient Visible Light-Induced Photocatalytic Degradation of Contaminant by Spindle-like PANI/ BiVO4,” The Journal of Physical Chemistry C, Vol. 113, No. 47, 2009, pp. 20228-20233. doi:10.1021/jp9067729
[2] R. Asahi, T. Morikawa, T. Ohwaki, K. Aoki and Y. Taga, “Visible-Light Photocatalysis in Nitrogen-Doped Titanium Oxides,” Science, Vol. 293, No. 5528, 2001, pp. 269-271. doi:10.1126/science.1061051
[3] R. Shi, J. Lin, Y. J. Wang, J. Xu and Y. F. Zhu, “Visible-Light Photocatalytic Degradation of BiTaO4 Photocatalyst and Mechanism of Photocorrosion Suppression,” The Journal of Physical Chemistry C, Vol. 114, No. 14, 2010, pp. 6472-6477. doi:10.1021/jp9101866
[4] L. Ge, M. X. Xu and H. B. Fang, “Synthesis of Novel Photocatalytic InVO4-TiO2 Thin Films with Visible Light Photoactivity,” Materials Letters, Vol. 61, No. 1, 2007, pp. 63-66. doi:10.1016/j.matlet.2006.04.006
[5] L. Ge, M. X. Xu and H. B. Fang, “Preparation of TiO2 Thin Films from Autoclaved Sol Containing Needle-like Anatase Crystals,” Applied Surface Science, Vol. 253, No. 2, 2006, pp. 720-725. doi:10.1016/j.apsusc.2005.12.162
[6] M. C. Long, W. M. Cai, J. Cai, B. X. Zhou, X. Y. Chai and Y. H. Wu, “Efficient Photocatalytic Degradation of Phenol over Co3O4/BiVO4 Composite under Visible Light Irradiation,” The Journal of Physical Chemistry B, Vol. 110, No. 41, 2006, pp. 20211-20216. doi:10.1021/jp063441z
[7] X. S. Zhou, F. Peng, H. J. Wang, H. Yu and J. Yang, “Effect of Nitrogen-Doping Temperature on the Structure and Photocatalytic Activity of the B,N-Doped TiO2,” Journal of Solid State Chemistry, Vol. 184, No. 1, 2011, pp. 134-140. doi:10.1016/j.jssc.2010.10.039
[8] X. S. Zhou, F. Peng, H. J. Wang and H. Yu, “Boron and Nitrogen-Codoped TiO2 Nanorods: Synthesis, Characterization, and Photoelectrochemical Properties,” Journal of Solid State Chemistry, Vol. 184, No. 11, 2011, pp. 3002-3007. doi:10.1016/j.jssc.2011.09.017
[9] M. Bowker, D. James, P. Stone, R. Bennett, N. Perkins, L. Millard, et al, “Catalysis at the Metal-Support Interface: Exemplified by the Photocatalytic Reforming of Methanol on Pd/TiO2,” Journal of Catalysis, Vol. 217, No. 2, 2003, pp. 427-433. doi:10.1016/S0021-9517(03)00074-5
[10] Y. X. Li, G. Lu and S. Li, “Photocatalytic Oxidation of Selected Fluorenols on TiO2 Semiconductor,” Journal of Photochemistry and Photobiology A: Chemistry, Vol. 152, No. 1-3, 2002, pp. 219-228. doi:10.1016/S1010-6030(02)00210-1
[11] L. L. Perissinotti, M. A. Brusa and M. A. Grela, “Yield of Carboxyl Anion Radicals in the Photocatalytic Degradation of Formate over TiO2 Particles,” Langmuir, Vol. 17, No. 26, 2001, pp. 8422-8427. doi:10.1021/la0155348
[12] M. Penpolcharoen, R. Amal and M. Brungs, “Degradation of Sucrose and Nitrate over Titania Coated NanoHematite Photocatalysts,” Journal of Nanoparticle Research, Vol. 3, No. 4, 2001, pp. 289-302.
[13] R. Jin, W. Gao, J. Chen, H. Zeng, F. Zhang, Z. Liu, et al, “Photocatalytic Reduction of Nitrate Ion in Drinking Water by Using Metal-loaded MgTiO3-TiO2 Composite Semiconductor Catalyst,” Journal of Photochemistry and Photobiology A: Chemistry, Vol. 1652, No. 2-3, 2004, pp. 585-590. doi:10.1016/S1010-6030(03)00420-9
[14] P. Chen, W. Li, T. L. Zhou, Y. P. Jin and M. Y. Gu, “Physical and Photocatalytic Properties of Zinc Ferrite Doped Titania under Visible Light Irradiation,” Journal of Photochemistry and Photobiology A: Chemistry, Vol. 168, No. 1-2, 2004, pp. 97-101. doi:10.1016/j.jphotochem.2004.05.018
[15] B. Xin, L. Jing, Z. Ren, B. Wang and H. Fu, “Effects of Simultaneously Doped and Deposited Ag on the Photocatalytic Activity and Surface States of TiO2,” The Journal of Physical Chemistry B, Vol. 109, No. 7, 2005, pp. 2805-2809. doi:10.1021/jp0469618
[16] A. Romanyuk, P. Oelhafen, “Formation and Electronic Structure of TiO2-Ag Interface,” Solar Energy Materials and Solar Cells, Vol. 91, No. 12, 2007, pp. 1051-1054. doi:10.1016/j.solmat.2007.02.016
[17] M. J. Kerker, “The Optics of Colloidal Silver: Something Old and Something New,” Colloid & Interface Science, Vol. 105, No. 2, 1985, pp. 297-314. doi:10.1016/0021-9797(85)90304-2
[18] P. Zhang, C. L. Shao, Z. Y. Zhang, M. Y. Zhang, J. B. Mu, Z. C. Guo, Y. Y. Sun and Y. C. Liu, “Core/Shell Nanofibers of TiO2@Carbon Embedded by Ag Nanoparticles with Enhanced Visible Photocatalytic Activity,” Journal of Materials Chemistry, Vol. 21, No. 44, 2011, pp. 17746-17753. doi:10.1039/c1jm12965a
[19] X. M. Sun and Y. D. Li, “Colloidal Carbon Spheres and Their Core/Shell Structures with Noble-metal Nanoparticles,” Angewandte Chemie International Edition, Vol. 43, No. 5, 2004, pp. 597-601. doi:10.1002/anie.200352386
[20] H. J. Wang, L. Yang, H. Yu and F. Peng, “A Highly Efficient and Stable Visible-Light Plasmonic Photocatalyst Ag-AgCl/CeO2,” World Journal of Nano Science and Engineering, Vol. 1, No. 4, 2011, pp. 129-136.
[21] Q. Lv, C. B. Cao, C. Li, J. T. Zhang, H. S. Zhu, X. Kong, et al., “Formation of Crystalline Carbon Nitride Powder by a Mild Solvothermal Method,” Journal of Materials Chemistry, Vol. 13, No. 6, 2003, pp. 1241-1243. doi:10.1039/b303210h
[22] Y. Qiu and L. Gao, “Chemical Synthesis of Turbostratic Carbon Nitride, Containing C-N Crystallites, at Atmospheric Pressure,” Chemical Communications, No. 18, 2003, pp. 2378-2379. doi:10.1039/b307086g
[23] E. Stathatos, P. Lianos, P. Falaras and A. Siokou, “Photocatalytically Deposited Silver Nanoparticles on Mesoporous TiO2 Films,” Langmuir, Vol. 16, No. 5, 2000, pp. 2398-2400. doi:10.1021/la981783t
[24] M. Sathish, B. Viswanathan, R. P. Viswanath and C. S. Gopinath, “Synthesis, Characterization, Electronic Structure, and Photocatalytic Activity of Nitrogen-Doped TiO2 Nanocatalyst,” Chemistry of Materials, Vol. 17, No. 25, 2005, pp. 6349-6353. doi:10.1021/cm052047v

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.