Design of a CMOS Optical Receiver Front-End Using 0.18 μm Technology ()

Ajay Shukla, Radheshyam Gamad, Rohan Raikwar

Department of Electronics & Instrumentation Engineering, S. G. S. Institute of Technology and Science, Indore, India.

**DOI: **10.4236/wet.2013.41007
PDF
HTML XML
5,383
Downloads
8,584
Views
Citations

Department of Electronics & Instrumentation Engineering, S. G. S. Institute of Technology and Science, Indore, India.

This paper reports design of a CMOS optical receiver front-end using 0.18 μm technology. Design process is current associated with photodiode using trans-impedance amplifier (TIA) for wide bandwidth, high gain, low input referred noise and wide dynamic range. The Automated Gain Control (AGC) voltage is used to provide variable gain for multilevel signals. This design is simulated in 0.18 μm UMC technology for the performance analysis. The best simulation results are reported the maximum TIA gain of 67.26 dB? at 0 V AGC followed by a post amplifier gain of 86.70 dB?. The bandwidth range is 7.03 GHz to 11.5 GHz corresponding to 0 - 3 V AGC respectively. The input referred noise level value is 43.86 pA/√Hz up to 10 GHz frequency. In addition authors have obtained the common mode rejection ratio (CMRR) is 72.42 dB and rectified group delay is 144.48 ps. Verification of the design, reported results are compared with earlier published work and improvements obtained in the present results.

Share and Cite:

A. Shukla, R. Gamad and R. Raikwar, "Design of a CMOS Optical Receiver Front-End Using 0.18 μm Technology," *Wireless Engineering and Technology*, Vol. 4 No. 1, 2013, pp. 46-53. doi: 10.4236/wet.2013.41007.

1. Introduction

Optical receivers find applications in laptop computers, cellular phones, digital cameras, computer peripherals, personal digital assistants (PDAs), and many other consumer electronics equipped with a short-distance communication port. A commonly used topology is the transimpedance (TIA) amplifier, whose relative low input impedance and wide bandwidth is well suited for the application [1]. A wide dynamic range is required for infrared wireless optical receivers in order to accommodate variable link distances, 0 ~ 100 cm. In the design of fixed-gain trans-impedance feedback amplifiers for infrared wireless receivers, there is a direct trade-off between input noise current and the input current overload level via the value of the shunt feedback resistor employed. Therefore, in order to enlarge the dynamic range, various means have been adopted to vary the gain of the trans-impedance amplifiers in response to the input signal levels. Variable-gain trans-impedance feedback amplifiers, however, are prone to instability [2]. TIA needs an Automated Gain Control (AGC) circuit to control the gain of the TIA in order to keep the different symbol levels equally spaced for multilevel signaling [3]. The TIA uses an AC coupled, differential version of the low-voltage topology outlined in [4], which is modified common-gate architecture. It is AC coupled to the photo detector (PD) using vertical parallel plate interconnects capacitors. Figure 1 shows the block representation of the receiver.

For open loop TIA the input resistance of this amplifier can be determined by [5]:

(1)

whererds_1 = the drain to source resistance gm_1 = the device trans-conductance Rd = the drain resistance and gmb_1 = the back-gate trans-conductance due to the body effect For long channel devices operating in the saturation region, the value of rds is large and it can be reduced by this relation:

(2)

This is an important result because the bandwidth is independent of the trans-impedance gain set by RD. The unfortunate downside of open loop TIA is that the noise current produced by the load resistance RD and the bias transistor are directly referred to the input with a unity factor therefore closed loop TIA are more preferable because the feedback resistor can be increased independently to the supply voltage since no bias current flows through it. The trans-impedance gain of an ideal inverting voltage amplifier with a feedback resistor Rfb can be given as [1]:

(3)

whereA = the open loop voltage gain of the amplifier.

Cpd = the photodiode capacitance.

If the voltages gain “A” of the amplifier is sufficiently high; the trans-impedance is approximately equal to Rfb in the amplifier’s pass band. Assuming that the dominant pole is at the input, the 3db bandwidth of this circuit will be given by the following expression as:

(4)

From Equation (4) it can be concluded that the bandwidth of the TIA is greater than that of a simple resistive network by a factor of A + 1. To reduce input referred noise current, TIA uses cascode noise from the resistor is directly referred to the input such that the mean squared input referred noise current spectral density is constant and given in equation

(5)

The group delay is defined as the negative of the derivative of the phase of the trans-impedance with respect to frequency [1] common-source topology with feedback resistor. This feedback resistor is implemented to single NMOS transistor in triode operation region because of process variation [6]. The input referred noise current is also dependent on the value of R_{L}. The

(6)

A flat group delay means the amplifier has a linear phase response. A flat group delay is important because variations in the group delay with frequency can cause distortions in the output signal.

2. Proposed Design

One of the issues to consider when comparing the two topologies common source and common gate is the effect of the Miller capacitance. Figure 2 shows a small signal equivalent model of the common source (CS) configuration.

Figure 1. Block diagram of CMOS optical receiver front-end.

Figure 2. Small signal equivalent model of the CS configuration.

The gate to drain capacitance C_{GD}, known as the Miller capacitance, is connected between the input and output. Miller’s theorem allows this capacitance to be replaced with shunt capacitances at the input and output [7]. Miller’s theorem can be derived using Figure 3. Series admittance is connected between two points with a known voltage gain of K. In order to replace this series admittance with shunt admittances the input and the output, the currents I_{1} and I_{2} must remain constant during the transformation.

The values of the shunt admittances can now be determined and are shown below.

(7)

(8)

This is an interesting result because as the gain is increased, the input capacitance of the amplifier is increased. This reduces the magnitude of the input pole and reduces the bandwidth of the TIA. This effect can be reduced by using the cascode configuration which minimizes the Miller effect by placing a common gate transistor in series with the common source transistor. A voltage gain stage was added after the trans-impedance stage [8]. This stage uses a simple resistive loaded differential pair. Also, for measurement purposes, an output buffer has been added to the TIA. The output buffer is also a resistive loaded differential pair with output impedance that is matched to 50 Ω. The post amplifier is implemented by a fully-differential two-stage operational trans-conductance amplifier [9,10]. Figure 4 shows a schematic view of the proposed design.

Figure 3. Miller theorem equivalent.

Figure 4. Schematic view of proposed design.

3. Results and Discussions

Figure 5 shows the transient analysis of optical receiver. In this the current at two differential inputs I_{6} and C1 is converted into the voltage forms using the trans-impedance amplifier. This converted voltage posses no distortion and expressed as the sinusoidal waves at the differential output which is further shifted its level to 3 V at the output of post amplifier.

Conflicts of Interest

The authors declare no conflicts of interest.

[1] | R. D. Bespalko, “Transimpedance Amplifier Design Using 0.18 μm CMOS Technology,” Queen’s University Kingston, Ontario, 2007. |

[2] | R. Y. Chen, T. S. Hung and C. Y. Hung, “A CMOS Infrared Wireless Optical Receiver Front-End with a Variable-Gain Fully-Differential Transimpedance Amplifier,” IEEE Transactions on Consumer Electronics, Vol. 51, No. 2, 2005, pp. 424-429. doi:10.1109/TCE.2005.1467982 |

[3] | S. Hranilovic and D. A. Johns, “A Multilevel Modulation Scheme for High-Speed Wireless Infrared Communications,” Proceedings of IEEE International Symposium on Circuits and Systems (ISCAS), Vol. 6, 1999, pp. 338-341. |

[4] | D. Guckenberger, J. Schaub and K. Komegay, “A DC Coupled Low-Power Transimpedance Amplifier Architecture for Gb/s Communication System Applications,” Design of Radio Frequency Integrated Circuit (RFIC) Symposium, June 2004, pp. 515-518. |

[5] | B. Razavi, “Design of Integrated Circuits for Optical Communications,” McGraw Hill, Boston, 2003. |

[6] | C. Ciofietal, “A New-Circuit Topology for the Realization of Very Low-Noise Wide-Bandwidth Trans-Impedance Amplifier,” IEEE Transactions on Instrument and Measurement, Vol. 56, No. 5, 2007 pp. 1626-1631. |

[7] | A. S. Sedra and K. C. Smith, “Microelectronic Circuits,” 4th Edition, Oxford University Press, New York, 1998. |

[8] | A. Phillip and D. R. Holberg, “CMOS Analog Circuit Design,” 2nd Edition, Oxford University Press, New York, 2003. |

[9] | F. T. Chien and Y. J. Chan, “Bandwidth Enhancement of Transimpedance Amplifier by a Capacitive Peaking Design,” IEEE Journal of Solid State Circuits, Vol. 34, 1999, pp. 1167-1170. |

[10] | S. M. Park and H.-J. Yoo, “1.25-Gb/s Regulated Cascade CMOS Transimpedance Amplifier for Gigabit Ethernet Applications,” IEEE Journal of Solid State Circuits, Vol. 39, No. 1, 2004, pp. 112-121. doi:10.1109/JSSC.2003.820884 |

Journals Menu

Contact us

+1 323-425-8868 | |

customer@scirp.org | |

+86 18163351462(WhatsApp) | |

1655362766 | |

Paper Publishing WeChat |

Copyright © 2024 by authors and Scientific Research Publishing Inc.

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.