Effect of Micro Size Cenosphere Particles Reinforcement on Tribological Characteristics of Vinylester Composites under Dry Sliding Conditions


In this paper the friction and wear characteristics of vinylester and cenosphere reinforced vinylester composites have been investigated under dry sliding conditions, under different applied normal load and sliding speed. Wear tests were carried using pin on a rotating disc under ambient conditions. Tests were conducted at normal loads 10, 30, 50 and 70 N and under sliding velocity of 1.88, 3.14, 4.39 and 5.65 m/s. The results showed that the coefficient of friction decreases with the increase in applied normal load values under dry conditions. On the other hand for pure vinylester specific wear rate increases with increase in applied normal load. However the specific wear rate for 2%, 6%, 10% and 15% cenosphere reinforced vinylester composite decreases with the increase in applied normal load under dry conditions. The results showed that with increase in the applied normal load and sliding speed the coefficient of friction and spe- cific wear rate decreases under dry sliding conditions. It is also found that a thin film formed on the counterface seems to be effective in improving the tribological characteristics. The specific wear rates for pure vinylester and vinylester composite under dry sliding condition were in the order of 10-6 mm3/Nm. The results showed that the inclusion of cenosphere as filler materials in vinylester composites will increase the wear resistance of the composite significantly. SEM analysis has been carried to identify the wear mechanism.

Share and Cite:

Chauhan, S. and Thakur, S. (2012) Effect of Micro Size Cenosphere Particles Reinforcement on Tribological Characteristics of Vinylester Composites under Dry Sliding Conditions. Journal of Minerals and Materials Characterization and Engineering, 11, 938-946. doi: 10.4236/jmmce.2012.1110092.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] I. M. Hutchings, “Tribology Friction and Wear of Engi- neering Materials,” CRC Press, London, 1992.
[2] S. W. Zhang, “State of the Art of Polymer Tribology,” Tribology International, Vol. 31, No. 1-2, 1998, pp. 49- 60. doi:10.1016/S0301-679X(98)00007-3
[3] J. R. Vinson and T. Chou, “Composite Materials and Their Uses in Structures,” Applied Science Publishing, London, 1975.
[4] S. W. Tsai, “Strength Characteristics of Composite Mate- rials,” NASA Report: NASACR- 224, 1965.
[5] B. J. Briscoe, “Wear of Polymers: An Easy on Funda- mental Aspects,” Tribology International, Vol. 14, No. 4, 1981, pp. 231-243. doi:10.1016/0301-679X(81)90050-5
[6] R. Huang, “Engineering Plastic Handbook,” Mechanical Industry Press, Beijing, 2000.
[7] Z. K. Gahr, “Microstructure and Wear of Materials,” Elsevier, Amsterdam, 1987.
[8] K. Friedrich, K. J. Karger and Z. Lu, “Overview on Poly- mer Composites for Friction and Wear Application,” Journal of Theoretical and Applied Fracture Mechanics, Vol. 19, No. 1, 1993, pp. 1-11. doi:10.1016/0167-8442(93)90029-B
[9] N. Axen, S. Hogmark and S. Jacobson, “Friction and Wear Measurement Techniques,” In: B. Bhushan, Ed., Modern Tribology Handbook, CRC Press LLC, London, Vol. 1, 2001, pp. 493-510.
[10] Y. Yamaguchi, “Tribology of Plastic Materials,” Tribol- ogy Series, Elsevier, New York, Vol. 16, 1990.
[11] P. B. Mody, T. W. Chou and K. Friedrich, “Effect of Testing Condition and Microstructure on the Sliding Wear of Graphite Fiber/PEEK Matrix Composites,” Journal of Material Science, Vol. 23, No. 12, 1998, pp. 4319-4330. doi:10.1007/BF00551926
[12] P. Arivalagan, G. Chandramohan, Arunkumar and N. Palaniappan, “Studies on Dry Sliding Wear Behaviour of Hybrid Composites,” Browse Conference Publications of Frontiers in Automobile and Me- chanical Engineering, Chennai, 25-27 November 2010, pp. 46-49. doi:10.1109/FAME.2010.5714796
[13] S. Basavarajappa, K. V. Arun and J. Pauloand Davim, “Effect of Filler Materials on Dry Sliding Wear Behavior of Polymer Matrix Composites—A Taguchi Approach,” Journal of Minerals & Materials Characterization & Engineering, Vol. 8, No. 5, 2009, pp. 379-391.
[14] E. Santer, and H. Czinchos, “Tribology of Polymer,” Tribology International, Vol. 22, No. 2, 1989, pp. 102- 109.
[15] P. Hasim and T. Nihat, “Investigation of the Wear Be- haviour of a Glass-Fibre-reinforced Composites and Plain Polyester Resin,” Composites Science and Technology, Vol. 62, No. 3, 2002, pp. 367-370. doi:10.1016/S0266-3538(01)00196-8
[16] K. P. Sampathkumaran, S. Seetharamu, S. Vynatheya, S. Murali and R. K. Kumar, “SEM Observations of the Ef- fects of Velocity and Load on the Sliding Wear Charac- teristics of Glass Fabric-Epoxy Composites with Differ- ent Fillers,” Wear, Vol. 237, No. 1, 2000, pp. 20-27. doi:10.1016/S0043-1648(99)00300-2
[17] B. Suresha, G. Chandramohan, J. N. Prakash, V. Balu- samy, and K. Sankaranarayanasamy, “The Role of Fillers on Friction and Slide Wear Characteristics in Glass-Ep- oxy Composite Systems,” Journal of Minerals & Materi- als Characterization & Engineering, Vol. 5, No. 1, 2006, pp. 87-101.
[18] S. Bahadur, “The Development of Transfer Layers and Their Role in Polymer Tribology,” Wear, Vol. 245, No. 1-2, 2000, pp. 92-99. doi:10.1016/S0043-1648(00)00469-5
[19] B. P. Singh, R. C. Jain and I. S. Bharadwaj, “Synthesis, Characterization and Properties of Vinyl Ester Matrix Resins,” Journal of Polymer Science, Vol. 2, 1994, p. 941.
[20] S. R. Chauhan, A. Kumar and I. Singh, “Mechanical and Wear Characterization of Vinyl Ester Resin Matrix Com- posites with Different Co-Monomers,” Journal of Rein- forced Plastics and Composites, Vol. 28, No. 21, 2008, pp. 2675-2684.
[21] S. Kumar, S. Gowtham and M. Sharpe, “Carbon/Vinyl Ester Composites for Enhanced Performance in Marine Applications,” Journal of Reinforced Plastics and Com- posites, Vol. 25, No. 10, 2006, pp. 1101-1116. doi:10.1177/0731684406065194
[22] S. R. Chauhan, A. Kumar, I. Singh and P. Kumar, “Effect of Fly Ash Content on Friction and Dry Sliding Wear Behavior of Glass Fiber Reinforced Polymer Composites —A Taguchi Approach,” Journal of Minerals & Materials Characterization & Engineering, Vol. 9, No. 4, 2010, pp. 365-387.
[23] P. K. Kolay and D. N. Singh, “Physical, Chemical, Min- eralogical and Thermal Properties of Cenospheres from an Ash Lagoon,” Cement and Concrete Research, Vol. 31, No. 4, 2001, pp. 539-542. doi:10.1016/S0008-8846(01)00457-4
[24] W. D. Scott, “Vinyl Ester/Cenosphere Composite Materi- als for Civil and Structural Engineering,” Fiber Rein- forced Polymer International, Vol. 2, No. 3, 2005, pp. 2-5.
[25] R. J. Cardoso, A. Shukla and A. Bose, “Effect of Particle Size and Surface Treatment on Constitutive Properties of Polyester Cenosphere Composites,” Journal of Material Science, Vol. 37, No. 3, 2002, pp. 603-13. doi:10.1023/A:1013781927227
[26] S. Torrey, “Coal Ash Utilization: Fly Ash Bottom Ash and Slag,” Noyes Data, Park Ridge, 1978.
[27] A. Das and B. K. Satapathy, “Structural, Thermal, Me- chanical and Dynamic Mechanical Properties of Ceno- sphere Filled Polypropylene Composites,” Journal of Ma- terials and Design, Vol. 32, No. 3, 2011, pp. 1477-1484.
[28] M. A. Abdullah, “Characterization of ACS Modified Epoxy Resin Composites with Fly Ash and Cenospheres as Fillers: Mechanical and Microstructural Properties,” Journal of Polymer Composites, Vol. 32, No. 1, 2011, pp. 139-146.
[29] K. W. Y. Wong and R. W. Truss, “Effect of Flyash Con- tent and Coupling Agent on the Mechanical Properties of Flyash Filled Polypropylene,” Composites Science and Technology, Vol. 52, No. 3, 1994, pp. 361-368. doi:10.1016/0266-3538(94)90170-8
[30] N. Dadkar, “Performance Assessment of Hybrid Com- posite Friction Materials Based on Flyash-Rock Fibre- Combination,” Material Design, Vol. 31, No. 2, 2010, pp. 723-731. doi:10.1016/j.matdes.2009.08.009
[31] E. Raask, “Cenosphere in Pulverized-Fuel Ash,” Journal of the Institute of Fuel, Vol. 41, No. 332, 1968, pp. 339- 344.
[32] G. L. Fisher, D. P. Y. Chang and M. Brummer, “Fly Ash Collected from Electrostatic Precipitators: Microcrystal- lines Structures and the Mystery of the Spheres,” Science, Vol. 192, No. 4239, pp. 553-555. doi:10.1126/science.192.4239.553
[33] B. D. Agarwal and L. J. Broutman, “Analysis and Per- formance of Fiber Composites,” 2nd Edition, John Wiley and Sons, Inc., Hoboken, 1990.
[34] S. S. Mahapatra and A. Patnaik, “Study on Mechanical and Erosion Wear Behavior of Hybrid Composites Using Taguchi Experiment Design,” Materials and Design, Vol. 30, No. 8, 2009, pp. 2791-2801. doi:10.1016/j.matdes.2009.01.037
[35] M. B. Kulkarniand and P. A. Mahanwar, “Effect of Methyl Methacrylate—Acrylonitrile Butadiene—Styrene (MABS) on the Mechanical and Thermal Properties of Poly (Methyl Methacrylate) (PMMA)-Fly Ash Ceno- spheres (FAC) Filled Composites,” Journal of Minerals & Materials Characterization & Engineering, Vol. 11, No. 4, 2012, pp. 365-383.

Copyright © 2024 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.