Scientific Research

An Academic Publisher

**Multiplierless Wideband and Narrowband CIC Compensator for SDR Application** ()

Share and Cite:

*International Journal of Communications, Network and System Sciences*,

**10**, 19-26. doi: 10.4236/ijcns.2017.108B003.

1. Introduction

Software-defined radio (SDR) has found important role in modern wireless communications. The main idea in SDR is to move the analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) as close as possible to the antenna and thus perform all signal processing in the digital form [1]. As a consequence, SDR is able to support different wireless standards using the same hardware. Knowing that different wireless standards require different sampling rate for baseband processing, the sampling-rate conversion (SRC) becomes a key operation in a SDR receiver [2].

SRC involves resampling in a digital domain thus causing aliasing and imaging which must be eliminated by filtering [3]. CIC (cascaded-integrator-comb) filter proposed in [4] is widely used as anti-aliasing and anti-imaging filter due to its simplicity: the filter requires no multiplication or coefficient storage. The transfer function of the CIC decimation filter in z-domain is given as:

, (1)

where M is the decimation factor and K is the number of the cascaded filters.

However, its magnitude characteristic:

, (2)

exhibits a low attenuation in the stopband of interest and a passband droop in the band of interest. As K increases, the stopband attenuation increases, resulting in an increased droop in the passband, which may deteriorate the decimated signal. The motivation of this work is to achieve good CIC wideband and narrowband compensation while keeping low rate of addition operations.

Different methods were proposed to compensate for the CIC passband droop. The compensators which need multipliers were proposed for example in [5] [6] [7]. However, due to lower power consumption, multiplierless compensators [8]-[13] are of more interest for SDR application. A two/stage CIC compensator with sinewave form of magnitude responses was recently proposed in [13]. The parameters of design are amplitudes of sinewaves expressed as sum-of-powers- of-two (SPT), and chosen in a way to provide better compensation than any other multiplierless compensator from literature. (The absolute value of the maximum passband deviation of the compensated comb is less than 0.1 dB). The compensator requires 11 adders for K = 2, 4, and 5, and 10 adders for K = 3, and 6. The goal here is to design a compensator requiring even fewer adders than the compensator in [13] while permitting a slight increase of the absolute value of the maximum passband deviation. The method is based on the sinewave magnitude responses multiplierless filters.

The paper is organized in the following way. Next section introduces transfer function of the proposed filter and describes the choice of the design parameters for wideband and narrowband compensation. Some comparisons are provided in Section 3.

2. Proposed Compensator

2.1. Transfer Function of Proposed Compensator

Like compensator in [13], the proposed compensator has magnitude response in the form:

, (3)

. (4)

. (5)

In contrast to the method in [13], we express the parameters of sinusoidal functions as powers of two, in order to decrease the number of the required adders:

. (6)

where N_{1} and N_{2} are integers.

The corresponding transfer function at low rate becomes:

, (7)

where

, (8)

and

. (9)

As a result, filters (8) and (9) require 6 and 3 adders, respectively, i.e. the compensator (7) requires total of 9 adders.

2.2. Wideband Compensation

We consider the passband edge ω_{p} = π/(2M), and impose the following condition:

(10)

where:

, (11a)

, (11b)

. (11c)

Considering M > 10 the compensator parameters do not depend on M, [13]. Using the MATLAB simulation, and taking the condition (10), we can easily find the parameters B_{1} and B_{2}, for K = 1, ・・・, 5, shown in Table 1. The number of required adders is equal to 9, for K = 2, ・・・, 5, and 6 for K = 1. The maximum passband deviation is obtained for K = 4, (0.25 dB), while the smallest one is for K = 1, (0.14 dB).

Figure 1 illustrates the passband zooms for different values of K and M = 15.

The method is illustrated in the following example.

Example 1: We consider the value of M = 18 and K = 5. According to Table 1, the values of B_{1} and B_{2} are equal to 1/2 and 1, respectively. Figure 2 compares the magnitude responses of the compensated CIC and the corresponding CIC filter. The passband zooms show that the absolute value of the maximum passband

Table 1. Parameters B_{1} and B_{2} for wideband compensation.

Figure 1. Passband zooms for compensated comb for M = 15 and K = 1, ・・・, 5.

Figure 2. Magnitude responses of CIC and compensated CIC filters.

deviation is lesser than 0.23 dB. The proposed compensator requires 9 adders.

The overall magnitude responses in Figure 2 confirm that the proposed compensator, despite the slight increase in the magnitudes of side lobes, does not deteriorate the attenuations in the folding bands.

2.3. Narrowband Compensation

We consider the passband edge ω_{p} = π/(8M) for narrowband compensation and the following condition:

(12)

where:

, (13)

and G_{1}(e^{jwM}) and G_{2}(e^{jwM}) are given in (11b) and (11c), respectively.

Applying the MATLAB simulation we got the values of parameters B_{1} and B_{2}, shown in Table 2. The method is illustrated in Example 2.

Example 2: We consider values of M = 21 and K = 5 and the passband edge of ω_{p} = π/(8M). Figure 3 shows the overall magnitude responses and the passband zooms for the compensated CIC and CIC filters. The absolute value of the passband deviation of the compensated CIC is lesser than 0.05 dB. The compensator requires only three adders.

In next section are given some comparisons with the recently proposed compensators.

3. Some Comparisons

3.1. Comparison with Method in [13]

Consider M = 20 and K = 5. Figure 4 compares the passband zooms of the proposed compensator and compensator in [13]. The parameters in the proposed method are: B_{1} = 1/2, B_{2} = 1. The parameters of the compensator in [13] are: B_{1} = 1 and, B_{2} = 2^{0} − 2^{−2} − 2^{−5}, thus requiring total of 11 adders.

3.2. Comparison with Method in [12]

The compensator in [12] has two second order sections both with sine-squared

Table 2. Parameters B_{1} and B_{2} for narrowband compensation.

Figure 3. Magnitude responses of CIC and compensated CIC filters.

magnitude responses with amplitudes of sine squared functions B_{1} and B_{2}. The value of B_{1} is equal to 2^{−3} for all values of K, while B_{2} = (1 + 4(K − 1))/16. For the sake of comparison we consider M = 16 and K = 5. The compensator in [12] requires 7 adders. The passband zoom is shown in Figure 5.

3.3. Comparison with Method in [9]

The proposed compensator is compared with that in [9], taking M = 32 and K = 5. The result is shown in Figure 6. The compensator in [9] has 5 coefficients and requires 14 adders.

Figure 4. Comparison with method in [13].

Figure 5. Comparison with method in [12].

Figure 6. Comparison with method in [9].

Conflicts of Interest

The authors declare no conflicts of interest.

[1] | Mitola, J. (1995) The Software Radio Architecture. IEEE Communication Magazine, 33, 26-38. https://doi.org/10.1109/35.393001 |

[2] | Hentschel, T. and Fettweis, G. (2000) Sample Rate Conversion for Software Radio. IEEE Communication Magazine, 38, 142-150. https://doi.org/10.1109/35.860866 |

[3] | Jovanovic Dolecek, G. (Ed-itor) (2001) Multirate Systems: Design and Application, IGP Hershey. |

[4] | Hogenauer, E.B. (1981) An Economical Class of Digital Filters for Decimation and Interpolation. IEEE Transactions on Acoustics, Speech and Signal Processing, 29, 155-162. https://doi.org/10.1109/TASSP.1981.1163535 |

[5] | Fernandez-Vazquez, A. and Jovanovic Dolecek, G. (2012) Maximally Flat CIC Com- pensation Filter: Design and Multiplierless Implementation. IEEE Transactions on Circuits and Systems II: Express Brief, 59, 113-117. https://doi.org/10.1109/TCSII.2011.2180093 |

[6] | Molnar, G. and Vucic, M. (2011) Closed-Form Design of CIC Compen-sators Based on Maximally Flat Error Criterion. IEEE Transactions on Circuits and Systems II: Express Brief, 58, 926-930. https://doi.org/10.1109/TCSII.2011.2172522 |

[7] | Kim, S., Lee, W.C., Alm, S. and Choi, S. (2006) Design of CIC Roll-Off Compensation Filter in a W-CDMA Digital Receiver. Digital Signal Processing, 16, 846-854. https://doi.org/10.1016/j.dsp.2006.06.003 |

[8] | Jovanovic Dolecek, G. (2009) Simple Wideband CIC Compensator. IET Electronics Letters, 45, 1270-1272. https://doi.org/10.1049/el.2009.1860 |

[9] | Pecotic, M., Molnar, G. and Vucic, M. (2012) Design of CIC Compensators with SPT Coefficients Based on Interval Analysis. Proceedings of 35th IEEE Int. Con-vention MIPRO 2012, IEEExplore, Opatija, Croatia, 123-128. |

[10] | Jovanovic Dolecek, G. and Fernandez-Vazquez, A. (2014) Trigonometrical Approach to Design a Simple Wideband Comb Compensator. International Journal for Electronics and Communications (AEUE), 68, 437-441. https://doi.org/10.1016/j.aeue.2013.11.007 |

[11] | Romero, E.T. and Jovanovic Dolecek, G. (2013) Application of Ampli-tude Transfor- mation for Compensation of Comb Decimation Filters. Electronics Letters, 49, 985- 987. https://doi.org/10.1049/el.2013.1492 |

[12] | Jovanovic Dolecek, G. (2016) A Novel Comb Compensator with a Good Pass-band Deviation-Complexity Tradeoff. Proceedings of 2016 IEEE 59th International Midwest Symposium on Circuits and Systems (MWSCAS), IEEEXplore, Abu Dhabi, United Arab Emirates (UAE), 137-140. |

[13] | Jovanovic Dolecek, G., Garcia Baez, R., Molina Salgado, G. and de la Rosa, J. (2017) Novel Multiplierless Wideband Compensator with High Compensation Capability. Circuits, Systems and Signal Processing, 36, 2031-2049. https://doi.org/10.1007/s00034-016-0398-0 |

Copyright © 2020 by authors and Scientific Research Publishing Inc.

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.