Share This Article:

Three-Dimensional Stress Concentration Factor in Finite Width Plates with a Circular Hole

Abstract Full-Text HTML XML Download Download as PDF (Size:1535KB) PP. 153-159
DOI: 10.4236/wjm.2013.33013    7,245 Downloads   12,584 Views   Citations

ABSTRACT

The three-dimensional stress concentration factor (SCF) at the edge of elliptical and circular holes in infinite plates under remote tension has been extensively investigated considering the variations of plate thickness, hole dimensions and material properties, such as the Poisson’s coefficient. This study employs three dimensional finite element modeling to numerically investigate the effect of plate width on the behavior of the SCF across the thickness of linear elastic isotropic plates with a through-the-thickness circular hole under remote tension. The problem is governed by two geometric non-dimensional parameters, i.e., the plate half-width to hole radius (W/r) and the plate thickness to hole radius (B/r) ratios. It is shown that for thin plates the value of the SCF is nearly constant throughout the thickness for any plate width. As the plate thickness increases, the point of maximum SCF shifts from the plate middle plane and approaches the free surface. When the ratio of plate half-width to hole radius (W/r) is greater than four, the maximum SCF was observed to approximate the theoretical value determined for infinite plates. When the plate width is reduced, the maximum SCF values significantly increase. A polynomial curve fitting was employed on the numerical results to generate empirical formulas for the maximum and surface SCFs as a function of W/r and B/r. These equations can be applied, with reasonable accuracy, to practical problems of structural strength and fatigue, for instance.

Conflicts of Interest

The authors declare no conflicts of interest.

Cite this paper

M. Vaz, J. Cyrino and G. Silva, "Three-Dimensional Stress Concentration Factor in Finite Width Plates with a Circular Hole," World Journal of Mechanics, Vol. 3 No. 3, 2013, pp. 153-159. doi: 10.4236/wjm.2013.33013.

References

[1] R. C. J. Howland, “On the Stresses in the Neighbourhood of a Circular Hole in a Strip under Tension,” Philosophical Transactions of the Royal Society of London, Vol. 229, 1930, pp. 49-86. doi:10.1098/rsta.1930.0002
[2] S. Timoshenko and J. N. Goodier, “Theory of Elasticity,” 2nd Edition, McGraw-Hill Book Company, New York, 1951.
[3] N. I. Muskhelishvili, “Some Basic Problems of the Mathematical Theory of Elasticity,” Groningen, 1953.
[4] W. T. Koiter, “An Elementary Solution of Two Stress Concentration Problems in the Neighborhood of a Hole,” Quarterly of Applied Mathematics, Vol. 15, 1957, pp. 303-308.
[5] V. J. Parks and D. F. Mendoza, “Maximum Stress in a Tensile Strip with a Large Hole,” Experimental Mechanics, Vol. 15, No. 10, 1975, pp. 389-391. doi:10.1007/BF02319837
[6] A. M. Wahl, “Discussion of ‘Maximum Stress in a Tensile Strip with a Large Hole’,” Experimental Mechanics, Vol. 16, No. 11, 1976, pp. 439-440. doi:10.1007/BF02410352
[7] R. D. Cook, “Stresses in a Tensile Strip with a Large Circular Hole,” Computers & Structures, Vol. 24, No. 3, 1986, pp. 421-424. doi:10.1016/0045-7949(86)90319-6
[8] B. Pradhan, “Effect of Width and Axial to Transverse Elastic Stiffness Ratio on SCF in Uniaxially Loaded FRP Composite Plates Containing Circular Holes,” Fiber Science and Technology, Vol. 17, No. 4, 1982, pp. 245-254. doi:10.1016/0015-0568(82)90020-3
[9] W. D. Pilkey, “Peterson’s Stress Concentration Factors,” 2nd Edition, John Wiley & Sons, New York, 1997. doi:10.1002/9780470172674
[10] D. Bellett, D. Taylor, S. Marco, E. Mazzeo, J. Guillois and T. Pircher, “The Fatigue Behaviour of Three-Dimensional Stress Concentrations,” International Journal of Fatigue, Vol. 27, No. 3, 2005, pp. 207-221. doi:10.1016/j.ijfatigue.2004.07.006
[11] D. Bellett and D. Taylor, “The Effect of Crack Shape on Fatigue Limit of Three-Dimensional Stress Concentrations,” International Journal of Fatigue, Vol. 28, No. 2, 2006, pp. 114-123. doi:10.1016/j.ijfatigue.2005.04.010
[12] W. Altenhof, N. Zamani, W. North and B. Arnold, “Dynamic Stress Concentrations for an Axially Loaded Strut at Discontinuities Due to an Elliptical Hole or Double Circular Notches,” International Journal of Impact Engineering, Vol. 30, No. 3, 2004, pp. 255-274. doi:10.1016/S0734-743X(03)00068-X
[13] C. She and W. Guo, “Numerical Investigations of Maxi mum Stress Concentration at Elliptic Holes in Finite Thickness Piezoelectric Plates,” International Journal of Fatigue, Vol. 28, No. 4, 2006, pp. 438-445. doi:10.1016/j.ijfatigue.2005.06.046
[14] C. She and W. Guo, “Three-Dimensional Stress Concentrations at Elliptic Holes in Elastic Isotropic Plates Subjected to Tensile Stress,” International Journal of Fatigue, Vol. 29, No. 2, 2007, pp. 330-335. doi:10.1016/j.ijfatigue.2006.03.012
[15] P. Yu, W. Guo, C. She and J. Zhao, “The Influence of Poisson’s Ratio on Thickness-Dependent Stress Concentration at Elliptic Holes in Elastic Plates,” International Journal of Fatigue, Vol. 30, No. 1, 2007, pp. 165-171. doi:10.1016/j.ijfatigue.2007.02.007
[16] Z. Yang, C. B. Kim, C. Cho and H. G. Beom, “The Concentration of Stress and Strain in Finite Thickness Elastic Plate Containing a Circular Hole,” International Journal of Solids and Structures, Vol. 45, No. 3-4, 2008, pp. 713-731. doi:10.1016/j.ijsolstr.2007.08.030
[17] D. V. Kubair and B. Bhanu-Chandar, “Stressconcentration Factor Due to a Circular Hole in Functionally Graded Panels under Uniaxial Tension,” International Journal of Mechanical Sciences, Vol. 50, No. 4, 2008, pp. 732-742. doi:10.1016/j.ijmecsci.2007.11.009
[18] C. K. Chao, L. M. Lu, C. K. Chen and F. M. Chen, “Analytical Solution for a Reinforcement Layer Bonded to a Elliptic Hole under a Remote Uniform Load,” International Journal of Solids and Structures, Vol. 46, No. 14 15, 2009, pp. 2959-2965. doi:10.1016/j.ijsolstr.2009.03.025
[19] J. Rezaeepazhand and M. Jafari, “Stress Concentration in Metallic Plates with Special Shaped Cutout,” International Journal of Mechanical Sciences, Vol. 52, No. 1, 2010, pp. 96-102. doi:10.1016/j.ijmecsci.2009.10.013
[20] “ANSYS® User’s Manual. Structural Analysis Guide,” Release 10.0 Documentation, 2005.
[21] American Society for Testing Materials, “Standard Specification for Structural Steel for Ships,” A131/A131M, 2008.

  
comments powered by Disqus

Copyright © 2019 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.