Elimination of Oil Residual inside the Copper Pipe Using Ladder Technique

DOI: 10.4236/eng.2013.51002   PDF   HTML   XML   3,828 Downloads   5,308 Views  


This study presents the methodology to eliminate oil residual in copper pipe due to rolling process for manufacturing coil used in air conditioner. The pressure caused by Nitrogen flow rate was applied starting from 0, 5, 10, and 15 bar, respectively which was depending on time delay and pipe length. The developed system was divided into 2 modules: Parallel pressure ladder module (PPLM) [1] and Serial pressure ladder module (SPLM) which were experimented with 2 sizes of copper pipe: diameter 7.29 mm, thickness 0.25 mm, and length 10 km, and diameter 8 mm, thickness 0.25 mm, and length 10 km. From experiment, it can be noted that PPLM would perform better in elimination of oil residual compared to SPLM. About 97.44% (0.04 mg/m) and 97.59% (0.05 mg/m) of oil residual can be respectively eliminated from diameter 7.29 mm pipe and diameter 8 mm pipe which exceeded the standard allowance of 30% or 0.1 mg/m. Moreover, the cost of Nitrogen can be reduced by 6.25% per month.

Share and Cite:

W. Sriratana and R. Murayama, "Elimination of Oil Residual inside the Copper Pipe Using Ladder Technique," Engineering, Vol. 5 No. 1, 2013, pp. 8-15. doi: 10.4236/eng.2013.51002.

Conflicts of Interest

The authors declare no conflicts of interest.


[1] W. Sriratana, N. Tammarugwattana, S. Ganmanee and L. Tanachaikhan, “Application of Parallel Ladder Technique for Purging Oil Residual inside the Copper Pipe,” IEEE 3rd International Conference on Communication Software and Networks, Xi’an, 27-29 May 2011, pp. 72-75.
[2] C. Chaiyachit, S. Satthamsakul, W. Sriratana and T. Suesut, “Hall Effect Sensor for Measuring Metal Particles in Lubricant,” International Multi Conference of Engineers and Computer Scientists, Hong Kong, 14-16 March 2012, pp. 894-897.
[3] E. O. Doebelin, “Measurement System: Application and Design,” 5th Edition, International Edition, Singapore City, 2003, pp. 578-672.
[4] Y. Taitel, U. Minzer and D. Barnea, “A Control Procedure for the Elimination of Mal Flow Rate Distribution in Evaporating Flow in Parallel Pipes,” Solar Energy, Vol. 82, No. 4, 2008, pp. 329-335. doi:10.1016/j.solener.2007.09.005
[5] J. H. Z. and X. Chen, “Monitoring and Control of Gas Flow Rate in a Pyrocarbon Coating Furnace for Heart Valves,” International Conference on Consumer Electronics, Communications and Networks, Xianning, 16-18 April 2011, pp. 4189-4193.
[6] M. A. Atmanand and M. S. Konnur, “A Novel Method of Using a Control Valve for Measurement and Control of Flow,” IEEE Transactions on Instrumentation and Measurement, Vol. 48, No. 6, 1999, pp. 1224-1226. doi:10.1109/19.816140
[7] K. Ohira, T. Nakayama and T. Nagai, “Cavitation Flow Instability of Subcooled Liquid Nitrogen in Converging-Diverging Nozzles,” Cryogenics, Vol. 52, No. 1, 2012, pp. 35-44. doi:10.1016/j.cryogenics.2011.11.001
[8] P. F. Dunn, “Measurement and Data Analysis for Engineering and Science,” McGraw-Hill International Edition, New York, 2005, pp. 144-158.
[9] National Instruments Corporation, “LabVIEW User Manual,” National Instruments Corporation, Texas, 2003.
[10] United Kingdom Accreditation Service, “The Expression of Uncertainty and Confidence in Measurement,” United Kingdom Accreditation Service, London, 1997.

comments powered by Disqus

Copyright © 2020 by authors and Scientific Research Publishing Inc.

Creative Commons License

This work and the related PDF file are licensed under a Creative Commons Attribution 4.0 International License.