Journal of Minerals and Materials Characterization and Engineering

Journal of Minerals and Materials Characterization and Engineering

ISSN Print: 2327-4077
ISSN Online: 2327-4085
www.scirp.org/Journal/jmmce
E-mail: jmmce@scirp.org
"Effects of Pressure on the Mechanical Properties and Microstructure of Die Cast Aluminum A380 Alloy"
written by Kenneth N. Obiekea, Shekarau Y. Aku, Danjuma S. Yawas,
published by Journal of Minerals and Materials Characterization and Engineering, Vol.2 No.3, 2014
has been cited by the following article(s):
  • Google Scholar
  • CrossRef
[1] Industry 4.0 foundry data management and supervised machine learning in low-pressure die casting quality improvement
International Journal of …, 2022
[2] Evaluation of hardness and microstructural features in piston aluminum-silicon alloys after different ageing heat treatments
Results in Materials, 2022
[3] The Computational Fluid Dynamics Investigation on the Solidification of Aluminum Cast in Moulds with Different Thickness and the Influence of the Moderate Press
Farhany, MQ Kareem - Materials Science Forum, 2021
[4] Modélisation, Simulation et Expérimentation de la formation des défauts volumiques lors du moulage sous pression des alliages de Zinc
2020
[5] Study of interaction between molten aluminium and hot-work tool steel using DSC method
2020
[6] The Influence of In-Cavity Pressure on Heat Transfer and Porosity Formation During High-Pressure Die Casting of A380 Alloy
2020
[7] Андре Ле Незет (Groupe Renault, Франция), Николя де Ревьер (Groupe Renault, Франция), Лоик Кальба (Calcom ESI SA, Швейцария), Бадаринатх …
2020
[8] Kemijska, mehanska in toplotna obraba orodij ob stiku z aluminijevimi livnimi zlitinami
2020
[9] Mehrwert der Prozessmodellierung bei der Entwicklung von Druckgussteilen in der Automobilindustrie
2019
[10] DESIGN ANALYSIS AND OPTIMIZATION OF PISTON FOR SINGLE CYLINDER 4 – STROKE SPARK IGNITION ENGINE USING COUPLED STEADY-STATE THERMAL STRUCTURAL ANALYSIS
International Journal of Mechanical Engineering and Technology, 2019
[11] Evaluation of mechanical and electrical properties of squeeze cast 1xxx aluminium
2018
[12] Added Value of Process Modelling in Development of Automotive Die Casting Parts
2018
[13] Optimization for Shrinkage Porosity on Aluminium Alloy ADC-12 Material
International Journal for Scientific Research & Development, 2017
[14] Various Type of Defects on Pressure Die Casting for Aluminium Alloys
2017
[15] Caractérisation des variabilités Matériaux/Process pour une convergence produit de fonderie par approche prédictive
Thèse, 2017
[16] Effect of Si, Cu and processing parameters on Al-Si-Cu HPDC castings
Journal of Materials Processing Technology, 2017
[17] Phase reactions of the alloy timetal 125 and its thermomechanical treatments
2017
[18] Obstojnost orodnega jekla SITHERM S361R v staljenem aluminiju
2017
[19] Дискретні моделі пластичної деформації твердих тіл під впливом високого гідростатичного тиску
2016
[20] Discrete Models of Plastic Deformation of Solids Under the Action of High Hydrostatic Pressure
2016
[21] Modeling of yield strength in binary hypoeutectic alloy under high pressure solidification
Journal of Alloys and Compounds, 2016
[22] Thermal Fatigue of Die-Casting Dies: An Overview
The 3rd International Conference on Mechanical Engineering Research (ICMER 2015), 2016
[23] Influence of injection temperature and pressure on the microstructure, mechanical and corrosion properties of a AlSiCu alloy processed by HPDC
Materials & Design, 2015
[24] Results in Materials
[25] Microstructural Investigation of Cast 6063 Aluminium Rods Produced From Sand and Permanent Cast Moulds
Free SCIRP Newsletters
Copyright © 2006-2024 Scientific Research Publishing Inc. All Rights Reserved.
Top