American Journal of Analytical Chemistry
Vol.10 No.05(2019), Article ID:92338,18 pages
10.4236/ajac.2019.105014

Forward Looking Analysis Approach to Assess Copper Acetate Thermal Decomposition Reaction Mechanism

Itab Youssef, Sécou Sall, Thierry Dintzer, Sana Labidi*, Corinne Petit

Institut de Chimie et Procédés pour l’Energie, l’Environnement et la Santé, Université de Strasbourg, UMR7515 CNRS, 25 rue Becquerel, Strasbourg, France

Copyright © 2019 by author(s) and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY 4.0).

http://creativecommons.org/licenses/by/4.0/

Received: January 25, 2019; Accepted: May 7, 2019; Published: May 10, 2019

ABSTRACT

Thermal decomposition course of copper acetate monohydrate was monitored by combining diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) coupled with µ gas chromatography-mass spectrometry (µGC-MS) with other analytical techniques (thermogravimetry analysis and in situ X-ray diffraction). Non-isothermal kinetic was examined in air and Ar. A complete analysis of the evolution of infrared spectra matched with crystalline phase transition data during the course of reaction allows access to significant and accurate information about molecular dynamics. While thermogravimetry gives broad conclusion about two steps reaction (dehydration and decarboxylation), in line approach (in situ X-ray and in situ DRIFT coupled to µGC-MS) is proposed as an example of a new robust and forward-looking analysis. While decomposition mechanism of copper acetate monohydrate is still not well elucidated yet previously, the present in-line characterization results lead to accurate data making the corresponding mechanism explicit.

Keywords:

In-Operando Spectroscopy and Chromatography, Thermal Decomposition Reaction Mechanism, Copper Acetate, Cross-Linked Characterization Data

1. Introduction

Continuous reaction and analysis is a relevant approach for sustainable chemical process [1] [2] . Ideally, techniques should provide scalable data and should be suitable for adaptation to industrial equipment (for ultimate application to process and quality control). One of the main current challenges is to design noninvasive techniques able to analyze data about different reaction media: powder, solid, liquid and gases. Two strategies could be proposed: continuous sampling coupled with fast analytical technique on one hand and in situ spectroscopic analysis on the other hand. Both approaches are complementary.

Metal carboxylates are useful reagents particularly for organic synthesis [3] and applied in several fields of research as solid-state, surface chemistry and catalysis [3] [4] [5] [6] . The thermal decomposition of metal carboxylates is a feasible route to synthesize metal nanoparticles suitable for catalytic purposes [7] [8] with specific properties based on carboxylates species. This reaction pathway concerning reaction media and applied conditions tailor final products yield, selectivity and chemical structure. Thermal dehydration and decomposition of metal acetate have been studied broadly under various conditions [5] [9] [10] . Copper is an interesting metal according to its properties and environmental applications. For example, Cu or CuO nanoparticles are effective to remedy a range of bacterial pathogens involved in hospital-acquired infections [9] . Some green paintings are based on copper derivatives [11] as copper acetate, silicates, Cu(Ac)2∙H2O has a simple process under heating, one step of dehydration followed by a step of decomposition giving rise to CuxOy species as presented by Mansour [5] . Thermal gravimetric analysis (TGA) was a common tool for those studies and was used by some researchers to suggest the obtained copper oxides. Other researchers proposed intermediates species as Z. Lin et al. [12] with the formation of CuAc2 peroxides. Despite intensive studies of copper carboxylates structures, no clear mechanism had been hold to illustrate thermal decomposition of these precursors. Different mechanisms for copper acetate monohydrate thermal decomposition were proposed by several authors with some disagree with each other [5] [12] [13] . Proposal of those mechanisms was based on solid material state identification only. Several techniques are conventionally added to thermogravimetry analysis (TGA) for monitoring metal carboxylates species, coupling with differential scanning calorimetry (DSC) or additional analysis of samples with X-ray diffraction (XRD), electronic microscopies or infrared (IR) [5] [12] [14] . Each technique provides specific information of gas or solid species. Moreover, developing new process based on miniaturization and coupled analysis technique made reaction study cost-effective and intensified. To obtain decomposition and reaction mechanism, single characterization technique alone could not be enough. Recently, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) with an environmental reaction chamber was used by A. Kaftan et al. [15] to elucidate reaction mechanisms for water gas shift and methanol steam reforming. The present work deals with the development of in-situ analytical approach for thermal decomposition study of copper acetate precursor in miniaturized DRIFT chamber coupled to µ gas chromatography and mass spectrometry (µGC-MS). This original coupling with new analytical approach has been developed in the lab to produce a large number of data characteristic for gas and solid species in the same time and temperature. In this article, in-situ XRD and TGA analysis were matched with in-situ DRIFT coupled to µGC-MS to identify both reagents by one hand and solid and gas products by the other hand for thermal mechanism reaction. The original coupling detailed by the present work allows accessibility for accurate data about mechanism steps. This work reports in-line characterization of copper acetate monohydrate thermal decomposition as a potential example for mechanism proposal by the coupling of in-line techniques. Our article will appeal for researchers having focus on development of analytical techniques but also of solid chemistry and catalysis. It deals with an example of thermal decomposition reaction to present an optimal cross of multiple in-situ characterization results to discuss mechanism reaction with more accurate data. Mechanism understanding is crucial to control material structure, thermodynamic phase stability and synthesis process. By the present work, thermal decomposition of Cu(Ac)2∙H2O is used as an example to demonstrate that a simple profile of TGA correspond to complex phenomena at molecular scale detectable by coupled techniques.

2. Experimental

2.1. Materials

The commercial crystalline copper (II) acetate mono-hydrate Cu(Ac)2∙H2O (Ac=CH3COO) was an ACS product of reagent grade (>98%) and used without further purification.

2.2. Apparatus

The thermal decompositions of copper acetate were analyzed by various follow-up techniques: in-situ X-ray diffraction (XRD), thermogravimetry analysis (TGA), in-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) coupled to micro gas chromatography (µGC) and mass spectroscopy (MS).

2.3. Methods

2.3.1. Thermal Analysis

The X-ray diffraction of copper acetate monohydrate was performed using TUR-M62 diffractometer with copper anticathode (λ = 1.54 Å), 34 kV voltage and 25 mA current. The XRD patterns were acquired for 2θ angles ranging from 10˚ to 70˚, with 0.03˚ steps. The XRD measurements were conducted in temperature programmed mode. For this purpose, Bruker D8 Advance diffractometer equipped with temperature programmed chamber was used. The XRD patterns were collected at temperatures ranging from 30˚C to 400˚C with heating rate of 10˚C/min flowing air or Ar. After the heating, the solid decomposition products were analyzed at room temperature into the chamber. Corresponding diffractograms during the acetate decomposition were collected at 30˚C, 110˚C, 170˚C, 190˚C, 250˚C and 370˚C. Thermal decomposition of sample was carried out in a TGA thermogravimetry (series Q5000) of TA Instruments in a flowing air or argon atmosphere (10 ml∙min−1). Approximately, 2 - 3 mg of sample was heated in an open platinum crucible at a rate of 15˚C/min up to 400˚C, incorporating a controlled rate thermal analysis program. To confirm the feasibility of comparing sample results by different techniques, TGA of Cu(Ac)2∙H2O and Cu(Ac)2∙H2O in KBr were tested and gave almost the same result for the same temperatures.

2.3.2. In Situ DRIFT-GC and MS Coupled Measurements

The in-situ experiments have been performed in a Vertex 70 Bruker IR spectrometer equipped with a one-pot sample compartment. The in situ setup provides all necessary gas in and outlets for flow control and allows temperature measurements. Mass flows were regulated using mass flow controllers (Bronkhorst). For DRIFTS, we used a controlled temperature reaction home-made chamber (7 ml), smaller than high-temperature chamber from Harrick, fitted with ZnSe windows and a Praying Mantis diffuse reflection accessory (Harrick). Temperatures were directly measured in the center of the catalytic bed by mean of a 0.75 mm * 150 mm type K thermo-couple. The apparatus originality is due to its coupling mode: it is an IR spectrometer coupled with a mass spectrometer and gas phase chromatograph (μGC-MS). This allows measurements in situ during a reaction under controlled atmosphere. The flow of gas is recovered at the outlet of the chamber and is brought to through a transfer rod to the μGC-MS switchgear. The experiments are performed by a new coupled instrumentation obtained by miniaturized cell, a DRIFT spectroscopy, 3 micro gas chromatographs and a mass spectrometer. One of the present technique advantages is to allow data acquisition throughout the transformation on the solid material and on the produced gases simultaneously. The coupling with gas chromatography (gas molecule identification by mass spectrometry) makes possible to monitor continuously the emission of gas. These experimental steps are systematically carried out during the sample preparation for DRIFTS analysis. The QMS data shown here were corrected by the following m/z values obtained by calibration: CO2 gas (m/z = 44), H2O (m/z = 18), acetic acid (m/z = 60) and acetone (m/z = 43). The spectra are measured from 600 to 4000 cm−1 with a resolution of 4 cm−1 (15 spectra/second) and are directly collected by the computer. The reaction chamber is equipped with ZnSe windows and a gas flow of 10 cm3∙min−1 across the sample. The experiments are carried out from room temperature to 600˚C (15˚C∙min−1), to avoid heating during high temperature studies, the chamber is equipped with a cooled double wall of water flow to control temperature. Samples are prepared by dilution (10 wt%) with dry powder of potassium bromide (KBr) or zinc selenide (ZnSe) as a diluent. Different conditions of test are made to show the influence of the presence of water interaction with the diluent during the decomposition steps. Powders are milled together and then placed on the sample holder in the chamber. This cell is closed and purged with helium (10 mL/min) for 5 minutes, sufficient time to purge the small chamber. The desired gas is then introduced, with a purge of 5 minutes for each experimental conditions variation. All gases were used without further purification (He:Alphagaz 2, >99.9999%; Ar:Alphagaz 2, >99.9999%; synthetic air Air Products, >99.9999%). No reabsorption, especially water, has been observed by leaving KBr sample overnight under flow.

3. Results

3.1. Study of Copper Acetate Decomposition by XRD and TGA

In situ XRD profiles of Cu(Ac)2∙H2O under heat treatment at 30˚C, 110˚C, 170˚C, 190˚C, 250˚C and 370˚C are showed by Figure 1. Copper acetate monohydrate and copper acetate are both observed in the XRD profiles at room temperature and mainly Cu(Ac)2 at 110˚C under air and Ar. The decomposition of acetate species starts at 190˚C and finishes before 250˚C as shown by the acetate cristal disappearing on the XRD profile at 250˚C under air and at 190˚C under Ar. This compound, in opposition to other acetate as Co(Ac)2∙4H2O [16] , do not melted during the dehydration step. Between 190˚C and 250˚C, broad peaks appear in the range of 35˚ - 40˚ of 2θ. These profiles should correspond to intermediate species since copper oxides and copper are detected in XRD profiles further. According to heat treatment media, different oxides appear above 190˚C. Cu2O and CuO appear at 250˚C and 370˚C respectively under air. Whereas, these both oxides appear simultaneously under Ar and get transformed to Cu around 370˚C.

TGA/TGD curves of Cu(Ac)2∙H2O are shown in Figure 2. These studies confirm the two steps as presented mainly in the literature [5] [9] [12] , one first step for dehydration then decarboxylation with differences according to heat media. The curves of copper acetate monohydrate decomposition obtained by TGA/DTG (Figure 2) display mainly two mass loss steps in the temperature range from 22˚C to 400˚C, and one mass gain step in air. The corresponding data of mass changes are listed in Table 1. The listed experimental values of first mass loss step agree with theoretical value (9.0%) of absolute dehydration of Cu(Ac)2∙H2O under air and Ar. The second mass loss step was commonly attributed

Figure 1. XRD patterns for copper acetate monohydrate thermal decomposition under air and Ar.

Figure 2. TGA and DTG curves for thermal decomposition of Cu(Ac)2∙H2O in air (a), in Ar (b).

Table 1. Mass changes of Cu(Ac)2∙H2O thermal decomposition under air and Ar.

to Cu(Ac)2 decomposition since the experimental value of mass loss under air for this step is consistent with the theoretical one (−55.1%) [17] . The mass increase between 310 and 600˚C is lower than theoretical value (4%). Cu2O is only partially oxidized to CuO at 600˚C. According to XRD patterns, Cu(Ac)2 decomposition under Ar between 195˚C and 275˚C produce Cu2O and CuO which are reduced thereafter to Cu since the experimental value of the mass loss for steps was quite close to the theory value. Difference between theoretical and experimental values of mass gain under Ar could be explained by multi-crystal phase formation during heat treatment between 230˚C and 310˚C. TGA seems to propose a relative simple phenomena for the degradation of Cu(Ac)2∙H2O but do not explain reaction mechanism. Thus, solid and emitted gases must be analyzed simultaneously in situ to identify intermediate species and then elucidate Cu(Ac)2∙H2O thermal decomposition mechanism. According to TGA and XRD in situ results, Cu(Ac)2∙H2O thermal decomposition reaction could be given broadly as follow without consideration of organic moieties because of lack of corresponding data:

1) Cu(CH3COO)2∙H2O ® CuO under air;

2) Cu(CH3COO)2∙H2O ® Cu under Ar.

3.2. Analysis of Overall DRIFT Spectra Evolution during Copper Acetate Decomposition: Relation between Reaction Course and Modifications at the Molecular Scale

In this study, DRIFT analysis monitor phenomena occurring at the molecular scale during thermal decomposition reaction. To achieve this goal, main spectral regions were identified then we focused on a limited number of spectra for Cu(Ac)2∙H2O decomposition at specific temperature. The in situ DRIFT spectra of Cu(Ac)2∙H2O from room temperature to 410˚C in air and in He, are showed in Figure 3, and peaks assignment are listed in Table 2 in agreement with Z. Lin and Mathey [12] [14] .

3.2.1. Dehydration Step and Water Influence on DRIFT Spectra

As shown in Figure 4, absorptive peak of O-H bond of water (3380 cm−1) and free O-H (3585 cm−1) distinctly weaken from 100˚C approximately (beginning of H2O desorption from precursor solid surface) and corresponds to the dehydration of Cu(Ac)2∙H2O. The results from the DRIFT spectra complete the TGA/DTG results and show slower leaving of OH moieties under air than under inert gas. The small amount of water staying on copper is able to change the mechanism of acetate decomposition and this issue will be discussed later.

3.2.2. Decarboxylation/Decomposition Step

DRIFT domain spectrum between 1150 and 1850 cm−1 contained characteristic peak of bidentate/bridged copper acetate bonds vibration mainly. During decomposition course, we observed intensity variation and shift position of peak intensities in that spectra region (Figure 5). Consistent with other references in literature [18] [19] [20] [21] , DRIFT bands are observed for copper acetate dehydrate at 1608, 1580, 1441, and 1362 cm−1. The carboxylate symmetric stretch is located as two bands at 1441 and 1362 cm−1, while the asymmetric one is observed at 1608 and 1580 cm−1. Intensities of listed peaks are influenced by temperature variation according to moisture level on the substrate and configuration of organic moieties. Above 200˚C under air and Ar, bands of asymmetric stretching acetate at 1608 are cleaved to main bands at 1620 and 1580 cm−1 according to bidentate-monodentate transformation [22] (Figure 5). The diffractograms

Figure 3. In situ DRIFT of Cu(Ac)2∙H2O in KBr under air (a) and Ar (b) between 4000 and 800 cm−1.

Table 2. Assignments of DRIFT spectra of Cu(Ac)2∙H2O.

Figure 4. In situ DRIFT of Cu(Ac)2∙H2O in KBr under air (a) and Ar (b) between 3700 and 2700 cm−1.

Figure 5. In situ DRIFT of 1 Cu(Ac)2∙H2O in KBr under air (a) and Ar (b) between 1850 and 1150 cm−1.

of hydrated Cu(Ac)2 (Figure 1) is described as bidentate acetate in the range of 35˚ and 40˚ between 190˚C and 250˚C. Mixed with KBr, the bidentate function is sensitive to H2O-Cu bond length and carboxylate ligands are transformed from bidentate to monodentate species. This structure enhances water hooking on the neighborhood of carboxylate [22] at 1573 cm−1, [20] . Dehydration step is quite similar under Ar and air: specific bands of acetate ligands of Cu(Ac)2 at 1608, 1441 and 1362 cm−1 increase from 20˚C until 280˚C under air and 315˚C under Ar (Figure 5). Once this step is achieved, new bands at 1722 and 1260 cm−1 referring to C=O and C-OH stretch respectively in acetic acid [20] appear under air and Ar similarly. A main difference according heat treatment media is reported during this stage. Absorptive peaks at 1608 and 1442 cm−1 maintain rising intensity till 316˚C than fall at 600˚C under air. For inert gas, the latest bands disappeared between 315˚C and 367˚C with an increase of stretching bonds of acetic acid until 367˚C (Figure 5). This observation reveals that acetate ligands start to decompose earlier under Ar and are converted to adsorbed acetic acid mainly, while, acetate ligands still bonded to copper metallic center during decomposition step under air. With TGA alone, it wasn’t possible to prove the latest conclusion to assess differences in reaction mechanism under air and inert gas.

Figure 6 shows variation of peaks intensity referring to C-CH and C-O at 1044 and 942 cm−1 [23] respectively. These two bands increase from 20 to 367˚C under air than fall by the end of heat treatment. C-CH and C-O bonds decompose earlier under Ar since relative bands turn before 367˚C. This observation illustrates that CH3COO group bonded to metallic center as acetate ligand is converted to adsorbed acetic acid under Ar (Figure 5) before its complete decomposition after 367˚C. CH3COO bonds are strengthened within heat treatment at dehydration and decarboxylation stages according to monodentate-bidentate/bridged transition. According to Campbell and Sharrock [24] [25] binuclear metal centers of copper acetate (II) were proposed to explain compound structure according to NMR signal multiplicity. Mononuclear metal centers are bridged to stabilize electronic deficit on Cu metallic center for Cu acetate monohydrate. Figure 6 stresses this conclusion since carboxylate bonds are strengthened by peaks rise at 1044 and 942 cm−1 in the range of 20˚C and 315˚C.

Gaseous products as CO2, acetic acid, acetone and ethanol are also detected in the infrared chamber. These volatile products have been proposed in literature [5] [13] , which is matched with the present results. We coupled DRIFT with µGC-MS to follow dynamic volatile species emission during decomposition reaction. Characteristic species detected by coupled µGC/MS are CO2 gas (m/z = 44), H2O (m/z = 18), acetic acid (m/z = 60) and acetone (m/z = 43). Kinetic gas products emission is recorded within temperature increase and reported by Figure 7.

According to the quantification by injection pulses (Figure 8), the formation of CO2 corresponds to 88% of amount of carbon from acetate under air and only 15% under inert gas. Both moieties of acetate ( CH 3 and COO) were mainly

Figure 6. In situ DRIFT of Cu(Ac)2∙H2O in KBr under air (a) and Ar (b) between 1150 and 850 cm−1.

Figure 7. In situ DRIFT of Cu(Ac)2∙H2O in KBr under air (a) and Ar (b) between 2600 and 2150 cm−1.

oxidized under air but the decomposition of acetate involves the creation of intermediate compounds which is mainly acetic acid under Ar (acetone and ethanol are formed at minor). According to DRIFT (Figure 5) and GC-MS (Figure 7) analysis, Cu(Ac)2 ligands are decomposed in both conditions (air or inert gas) with some similar intermediate species oxidized only under air. The same observation could be made for peak evolution at 2361 cm−1 related to vibration modes of CO2 gas bonds (Figure 8). We examined the intensity of some characteristic peaks within temperature. Figure 9 shows the variation of peaks intensity corresponding to O?H stretching in water, C=O stretching, CO2 gas and C-CH3 framework vibration mode. This follow-up is used to monitor, within time and temperature, similarly to TGA analysis but with more accurate information than relative mass detection.

Figure 8. Gas emission quantification by µ GC-MS during Cu(Ac)2∙H2O decomposition under air (a) and Ar (b).

Figure 9. Bands intensities evolution of in situ DRIFT spectra within temperature for bonded O-H (3585 cm−1―black), free O?H (3380 cm−1―red), CO2 gas (2360 cm−1―green), C=O in acetic acid (1722 cm−1―blue), C=O asymmetric (1608 cm−1―orange) and C-CH (1044 cm−1―purple) of Cu(Ac)2∙H2O in KBr under air (a) and Ar (b).

4. Discussion

Scheme 1 (in annex section) describes mechanistic dynamic steps during thermal decomposition under air and Ar leading to CuO and Cu respectively as solid with emission of H2O, CO2, CH3COOH, H2 [26] (according reaction media) and coke deposit [27] . On Scheme 1, structures 1 and 2 describe binuclear complex dehydration step. XRD patterns confirm TGA results concerning dehydration process. H2O desorption ends at 170˚C under air and at 140˚C under Ar according to thermal analysis in agreement with XRD patterns (diffractograms pic of copper acetate monohydrate disappeared before 170˚C) and DRIFT analysis as shown by Figure 4. Structure transition 1 ® 2 could be traduced by the following reaction Equation (1):

2Cu ( CH 3 COO ) 2 H 2 O 2Cu ( CH 3 COO ) 2 + 2H 2 O { 2 0 ˚ C - 17 0 ˚ C under air 2 0 ˚ C - 14 0 ˚ C under Ar (1)

According to TGA data, thermal decomposition of Cu(Ac)2∙H2O ends at 310˚C under air and 275˚C under Ar. Nevertheless, Cu(Ac)2∙H2O signal on XRD patterns falls before, in the range of 190˚C and 250˚C (before 190˚C under Ar) with appearance of broad peaks at 2θ ranging from 35˚ to 40˚ (Figure 1). Crucially, we observe an increase of C-O stretching bond intensity at 944 cm−1 (Figure 6) from 20˚C to 310˚C approximately then a decrease reaching 600˚C. The correlation between the latest observations on TGA, XRD and DRIFT results is worth noting as it concludes on complex transition 2 ® 3 (Scheme 1): acetate ligands are shifted from bidentate to monodentate species. Figure 9 confirms this conclusion: C=O bands (1608 and 1718 cm−1) increased within temperature simultaneously with desorption of H2O moieties (fall of 3380 and 3585 cm−1 signal by the end of dehydration steps under Ar and air). Structure 3 is proposed according to H2O desorption step for carboxylic acid ketonization on acid-base pairs of TiO2 [28] . H2O desorption involves C-C coupling between 1-hydroxyl enolate and co-adsorbed acetate to form α-hydroxy γ-carboxy alkoxide. An XRD pattern (Figure 1) confirms Cu2O lattice formation under air and Ar starts at 190˚C - 250˚C. Thus, once dehydration step is achieved, Cu2O network appears (2 ® 3 transition in Scheme 1).

As mentioned by GC-MS data measurements (Figure 7), CO2 detection on gas phase starts at 300˚C under air and 250˚C under Ar and reaches maximal values at 413˚C and 367˚C respectively. Meanwhile, CO2 is detected on precursor surface from 200˚C (both Ar and air). Transition 3 ® 4 on Scheme 1 illustrates CO2 adsorption on cupric center than its desorption for transition 4 ® 5. Transition 3 ® 5 is resumed by Equation (2) as bellow:

2Cu ( CH 3 COO ) 2 ( CuO ) 2 ( 1-CO ( CH 3 ) CH 2 ) 2 + 2CO 2 { 300 ˚ C - 480 ˚ C under air 25 0 ˚ C - 45 0 ˚ C under Ar (2)

Air media promotes complete oxidation of acetate ligands to CO2 and H2O (transition 5 ® 6’). We note an involving rate of adsorbed acetic acid on Cu2O (Figure 9(a)) surface under air without its detection by GC-MS. This is explained adsorbed acetic acid oxidation to CO2 and H2O. Indeed, evolution of hydroxyl bands on Figure 4(a) and Figure 9(a) illustrates a signal rise from 280˚C to 360˚C, which is matching mechanism transition for the final step under air and Cu2O turns into CuO as latest crystalline phase (fig. a).

The transition 2 ® 3’’ on Scheme 1 is proposed as one step decomposition of Cu(Ac)2∙xH2O (x ≠ 0) to acetic acid and Cu under Ar without CO2 desorption and copper oxide intermediates. H2O is essential for this transition that its equilibrium is rather shifted for compound 2.

A notable difference is identified for thermal decomposition under Ar after 300˚C compared to the same one under air. Acetic acid is detected by GC-MS (Figure 7(b)) from 340˚C and reaches its maximum at 500˚C. Its desorption was also predicted by DRIFT spectra (Figure 5(b) and Figure 9(b)) since C=O stretching band at 1722 cm−1 increases from 340 until 400˚C, thus, CH3COOH was adsorbed on Cu2O surface before its desorption. Transition 5 ® 9 describe acetic acid desorption. This transition is deeply influenced by water adsorption on copper atoms. Residual H2O moieties in KBr, since its hygroscopic property, oxidize ligands by nucleophilic substitution. This reaction involves C-O coupling between 1-hydroxyl enolate and coordinated residual H2O to form α-hydroxy alkoxide. The latest intermediate is converted to Cu-CH3COOH and Cu-CH3 [28] (Scheme 1. 6 ® 9). On Figure 4, OH bands fall are more noticed under Ar rather than under air which confirms the latest hypothesis since H2O was consumed to form acetic acid. Figure 9(b) stresses this observation: no hydroxyl bands increase after 300˚C under Ar contrarily to air. Ligands decomposition under Ar involves Cu2O phase formation. Copper oxide turns to Cu between 250˚C and 370˚C with desorption of CO2 as described by Figure 9(b) plot.

To assess the influence of adsorbed water in mechanism reaction, two types of diluent were tested under Ar: KBr on one hand with hygroscopic property and ZnSe on the other hand. When the diluent is hygroscopic, C=O bands shifted during decomposition process (Figure 5) When the diluent does not interact with water as ZnSe, C=O bands are kept in the same position during heating. Mixed with ZnSe, acetate is bonded to copper as bidentate ligands during dehydration and decomposition steps under air and inert gas. Moreover, gaseous products for Cu(Ac)2∙H2O under Ar in ZnSe are different from similar reaction in KBr: GC-MS shows formation of acetone at the same level as acetic acid in addition to CO2 desorption earlier (annexe?). Acetone formation from acetate heat treatment is described as carboxylic acid ketonization catalyzed by metal oxides reported by several authors [28] . Acetic acid still formed with use of ZnSe which is explained by remained amount of H2O after dehydration step finished at 170˚C as proved by A. Musumeci and co. [10] . Moreover, desorbed products analyzation by TPD with corrected m/e of Ni acetate heat decomposition under He was performed by J.C. De Jesus et al. [8] and they confirm H2O desorption at 162˚C than at 373˚C with formation of acetic acid and acetone. KBr use leads to acetic acid selectivity so.

Transition 7 ® 8 illustrates copper methyl formation (CuCH3) and adsorbed acetic acid after nucleophilic substitution by H2O. Concerning adsorbed acetic acid, DRIFT spectra shows (Figure 9(b)) that its band got intensified from 200˚C to 400˚C before its decrease within temperature rise under Ar. Simultaneously, acetic acid (as free molecule) is quantified in gas phase by GC-MS from 350˚C to 500˚C than falls by the end of decomposition reaction (Scheme 1, 8 ® 9). Cho and co. [21] made infrared characterization of Cu-CH3 and listed 4 main bands at 1612 (Cu-H stretching in CH3-CuH), 1203 (CH3 deform in CH3-Cu), 1012 (CH3 deform in CH3-CuH) and 648 cm−1. Corresponding bands at 1611, 1198, 1011 and 655 cm−1 were identified on DRIFT spectra (Figure 5(b) and Figure 6(b)) and appeared between 315 and 367˚C under Ar. The latest bands are not identified under air (except for band at 655 cm−1 which is a large band under air). With increase of heat temperature, Cu-CH3 on Cu2O bond decomposition could lead to Cu2O, coke and H2 or αCHx in general (8 ® 9, Scheme 1). At the last step 9 ® 10, copper oxide is converted to Cu with emission of CO2 (re-increase of CO2 level at 500˚C approximately in Figure 7(b)).

Last steps of mechanism reaction are resumed by the following reactions equations system (3), (4) and (5) under air and Ar:

( CuO ) 2 ( 1-CO ( CH 3 ) CH 2 ) 2 2CuO + 6CO 2 + 5H 2 O 370 ˚ C - 600 ˚ C under air (3)

( CuO ) 2 ( 1-CO ( CH 3 ) CH 2 ) 2 2CH 3 COOH + 2Cu 2 O + 2C + 3H 2 30 0 ˚ C - 40 0 ˚ C under Ar (4)

2CH 3 COOH + 2Cu 2 O + 2C + 3H 2 2Cu + 1 2 CO 2 40 0 ˚ C - 60 0 ˚ C under Ar (5)

5. Conclusion

The present work deals with thermal decomposition of copper acetate monohydrate under air and Ar. A complete analysis of the evolution of infrared spectra matched with crystalline phase transition data allows to underline detailed steps for reaction mechanism. In-line µGC-MS results about chronologic desorption of major gaseous products (H2O, CO2 and CH3COOH) correlate favorably with DRIFT spectra observations and provide accurate information about intermediates structure of copper acetate during heat treatment. While TGA gives broad conclusion about two steps reaction (dehydration and decarboxylation), in line approach (in situ X-ray and in situ DRIFT coupled to µGC-MS) was used to assess H2O influence on reaction mechanism under Ar. In fact, H2O desorption is incomplete during dehydration step as defined by TGA and residual moieties are essential to conclude CH3COOH acetic acid formation, main gas product under Ar. The present in line approach is proposed as an example of a new robust and forward-looking analysis to highlight crucial information about reaction selectivity, conversion and product structure. This tool could be performed also to predict mechanism path way according to reaction media for a large numbre of products and precursors.

Conflicts of Interest

The authors declare no conflicts of interest regarding the publication of this paper.

Cite this paper

Youssef, I., Sall, S., Dintzer, T., Labidi, S. and Petit, C. (2019) Forward Looking Analysis Approach to Assess Copper Acetate Thermal Decomposition Reaction Mechanism. American Journal of Analytical Chemistry, 10, 153-170. https://doi.org/10.4236/ajac.2019.105014

References

  1. 1. Scalbert, J., Clemencon, I., Legens, C., Diehl, F., Decottignies, D. and Maury, S. (2015) Development of an Innovative XRD-DRIFTS Prototype Allowing Operando Characterizations during Fischer-Tropsch Synthesis over Cobalt-Based Catalysts under Representative Conditions. Oil & Gas Science and Technology, 70, 419-428. https://doi.org/10.2516/ogst/2014031

  2. 2. Price, G.A., Mallik, D. and Organ, M.G. (2017) Process Analytical Tools for Flow Analysis: A Perspective. Journal of Flow Chemistry, 7, 82. https://doi.org/10.1556/1846.2017.00032

  3. 3. Lin, D.C.K. and Westmore, J.B. (1973) Mass Spectral Studies of Binuclear Metal Complexes: Copper(I) Carboxylates. Canadian Journal of Chemistry, 51, 2999-3005. https://doi.org/10.1139/v73-446

  4. 4. Mansour, S.A.A., Hussein, G.A.M. and Zaki, M.I. (1990) Decomposition of Cd(CH3COO)2∙2H2O and Creation of Reactive Solid Surfaces—A Spectrothermal Investigation. Reactivity of Solids, 8, 197-208. https://doi.org/10.1016/0168-7336(90)80020-K

  5. 5. Mansour, S.A.A. (1996) Thermoanalytical Investigations of the Decomposition Course of Copper Oxysalts. Journal of Thermal Analysis, 46, 263-274. https://doi.org/10.1007/BF01979966

  6. 6. Brown, M.E., Dollimore, D. and Galwey, A.K. (1980) Reactions in the Solid State. In: Bamford, C.H. and Tipper, C.F.H., Eds., Comprehensive Chemical Kinetics, Elsevier, Amsterdam, 134-135.

  7. 7. Trimm, D.L. (1980) Design of Industrial Catalysts. In: Churchill, S.W., Ed., Chemical Engineering Monographs, Elsevier, Amsterdam, 3-36.

  8. 8. Jesus, J.C.D., Gonzalez, I., Quevedo, A. and Puerta, T. (2005) Thermal Decomposition of Nickel Acetate Tetrahydrate: An Integrated Study by TGA, QMS and XPS Techniques. Journal of Molecular Catalysis A: Chemical, 228, 283-291. https://doi.org/10.1016/j.molcata.2004.09.065

  9. 9. Ren, G., Hu, D., Cheng, E.W.C., Vargas-Reus, M.A., Reip, P. and Allaker, R.P. (2009) Characterisation of Copper Oxide Nanoparticles for Antimicrobial Applications. International Journal of Antimicrobial Agents, 33, 587-590. https://doi.org/10.1016/j.ijantimicag.2008.12.004

  10. 10. Musumeci, A. and Frost, R.L. (2007) A Spectroscopic and Thermoanalytical Study of the Mineral Hoganite. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 67, 48-57. https://doi.org/10.1016/j.saa.2006.05.037

  11. 11. Buti, D., Rosi, F., Brunetti, B.G. and Miliani, C. (2013) In-Situ Identification of Copper-Based Green Pigments on Paintings and Manuscripts by Reflection FTIR. Analytical and Bioanalytical Chemistry, 405, 2699-2711. https://doi.org/10.1007/s00216-013-6707-6

  12. 12. Lin, Z., Han, D. and Li, S. (2012) Study on Thermal Decomposition of Copper(II) Acetate Monohydrate in Air. Journal of Thermal Analysis and Calorimetry, 107, 471-475. https://doi.org/10.1007/s10973-011-1454-4

  13. 13. Afzal, M., Butt, P.K. and Ahmad, H. (1991) Kinetics of Thermal Decomposition of Metal Acetates. Journal of Thermal Analysis, 37, 1015-1023. https://doi.org/10.1007/BF01932799

  14. 14. Mathey, Y., Greig, D.R. and Shriver, D.F. (1982) Variable-Temperature Raman and Infrared Spectra of the Copper Acetate Dimer Cu2(O2CCH3)4(H2O)2 and Its Derivatives. Inorganic Chemistry, 21, 3409-3413. https://doi.org/10.1021/ic00139a028

  15. 15. Kaftan, A., Kusche, M., Laurin, M., Wasserscheid, P. and Libuda, J. (2017) KOH-Promoted Pt/Al2O3 Catalysts for Water Gas Shift and Methanol Steam Reforming: An Operando DRIFTS-MS Study. Applied Catalysis B: Environmental, 201, 169-181. https://doi.org/10.1016/j.apcatb.2016.08.016

  16. 16. Wanjun, T. and Donghua, C. (2007) Mechanism of Thermal Decomposition of Cobalt Acetate Tetrahydrate. Chemical Papers, 61, 329-332.

  17. 17. Zhang, K.L., Hong, J.H., Cao, G.H., Zhan, D., Tao, Y.T. and Cong, C.J. (2005) The Kinetics of Thermal Dehydration of Copper(II) Acetate Monohydrate in Air. Thermochimica Acta, 437, 145-149. https://doi.org/10.1016/j.tca.2005.06.038

  18. 18. Hudson, R.L., Gerakines, P.A. and Ferrante, R.F. (2018) IR Spectra and Properties of Solid Acetone, an Interstellar and Cometary Molecule. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 193, 33-39. https://doi.org/10.1016/j.saa.2017.11.055

  19. 19. Smith, B.C. (2017) The Carbonyl Group, Part I: Introduction. Spectroscopy, 32, 31-36.

  20. 20. DeCoste, J.B., Peterson, G.W., Schindler, B.J., Killops, K.L., Browe, M.A. and Mahle, J.J. (2013) The Effect of Water Adsorption on the Structure of the Carboxylate Containing Metal-Organic Frameworks Cu-BTC, Mg-MOF-74, and UiO-66. Journal of Materials Chemistry A, 1, 11922-11932. https://doi.org/10.1039/c3ta12497e

  21. 21. Cho, H.G. and Andrews, L. (2011) Infrared Spectra of CH3-MH, CH3-M, and CH3-MH-Prepared via Methane Activation by Laser-Ablated Au, Ag, and Cu Atoms. Dalton Transactions, 40, 11115-11124. https://doi.org/10.1039/c0dt01827a

  22. 22. Dudev, T. and Lim, C. (2004) Monodentate versus Bidentate Carboxylate Binding in Magnesium and Calcium Proteins: What Are the Basic Principles? The Journal of Physical Chemistry B, 108, 4546-4557. https://doi.org/10.1021/jp0310347

  23. 23. Mekhemer, G.A.H., Halawy, S.A., Mohamed, M.A. and Zaki, M.I. (2005) Ketonization of Acetic Acid Vapour over Polycrystalline Magnesia: In Situ Fourier Transform Infrared Spectroscopy and Kinetic Studies. Journal of Catalysis, 230, 109-122. https://doi.org/10.1016/j.jcat.2004.09.030

  24. 24. Campbell, G.C., Reibenspies, J.H. and Haw, J.F. (1991) Solid-State NMR Studies of Magne-to-Structural Correlations in Anhydrous Copper(II) Carboxylates. Inorganic Chemistry, 30, 171-176. https://doi.org/10.1021/ic00002a006

  25. 25. Sharrock, P. and Melnik, M. (1985) Copper(II) Acetates: From Dimer to Monomer. Canadian Journal of Chemistry, 63, 52-56. https://doi.org/10.1139/v85-009

  26. 26. Bellini, J.V., Machado, R., Morelli, M.R. and Kiminami, R.H.G.A. (2002) Thermal, Structural and Morphological Characterisation of Freeze-Dried Copper(II) Acetate Monohydrate and Its Solid Decomposition Products. Materials Research, 5, 453. https://doi.org/10.1590/S1516-14392002000400010

  27. 27. Costa, G., Camus, A. and Marsich, N. (1965) Copper Methoxides Formed by Thermal Decomposition of Copper Methyl in Methanol. Journal of Inorganic and Nuclear Chemistry, 27, 281-285. https://doi.org/10.1016/0022-1902(65)80339-6

  28. 28. Wang, S. and Iglesia, E. (2017) Experimental and Theoretical Assessment of the Mechanism and Site Requirements for Ketonization of Carboxylic Acids on Oxides. Journal of Catalysis, 345, 183-206. https://doi.org/10.1016/j.jcat.2016.11.006

Annex, Scheme 1: Cu(Ac)2∙H2O Reaction Mechanism of Thermal Decomposition under Air and Ar