Journal of Geoscience and Environment Protection
Vol.03 No.04(2015), Article ID:56946,8 pages
10.4236/gep.2015.34001

Removal of Fluoride from Groundwater by Carbonised Punica granatum Carbon (“CPGC”) Bio-Adsorbent

Sudhanshu Kanaujia1, Bharat Singh2, Sanjay Kumar Singh3

1Department of Chemistry, United College of Engineering and Research, Allahabad, India

2Department of Chemistry, University of Allahabad, Allahabad, India

3Department of Chemistry, Institute of Engineering and Technology, Lucknow, India

Email: sh.sudhanshu@gmail.com

Copyright © 2015 by authors and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY).

http://creativecommons.org/licenses/by/4.0/

Received 17 April 2015; accepted 1 June 2015; published 5 June 2015

ABSTRACT

This study applies the development and application of low cost, Punica granatum bio-adsorbent for the removal of fluoride in groundwater. The batch adsorption study was carried out to analyze the defluoridation by contact time variation, adsorbent dose, adsorbate concentration, adsorbent particle size and presence of co-anions at neutral pH. The analysis of the isotherm equilibrium data using the Langmuir and Freundlich equations by linear methods showed that the data fitted better with Freundlich model (R2 > 0.980). Prepared adsorbent showed enhanced removal of fluoride concentration by 78.1% at equilibrium contact time of 75 minutes. Carbonised Punica granatum Carbon (CPGC) seeds showed a high affinity for fluoride ions compared with other conventional adsorbents. Therefore, it can be considered as a potentially “good”, low-cost bio-adsorbent for de-fluoridation of water compared to other bio-adsorbent.

Keywords:

Fluoride Removal, Adsorption, Punica granatum, Bio-Adsorbent

1. Introduction

Water is one of the most important elements for all forms of life and is indispensable to the maintenance of life on earth. Safe drinking water is the primary need of every human being. Pure water is scarce and is not easily available at all. Water may be contaminated by natural sources or industrial effluents. One such contaminant is fluoride.

Fluoride (F) is a fluorine anion characterized by small radius, great tendency to behave as ligand and easiness to form a great number of different organic and inorganic compounds in soil, rocks, air, plants and animals. Some of those compounds are quite soluble in water and notable in both surface and groundwater as an almost completely dissociated fluoride ion [1] [2] . The presence of naturally occurring fluorides or added fluoridated salts in drinking water allows its easy entrance in the body via the gastrointestinal tract [3] [4] . The epidemiological studies reveal that drinking water is the major source of fluoride daily intake and continuous consumption of drinking water with elevated fluoride concentrations (>1.5 mg/l) can induce birth, reproduction and immunological defects [5] [6] , dental and skeletal fluorosis [7] [8] . Besides drinking water, fluoride can also enter into the human body through food, industrial exposure, drugs, cosmetics, etc. [1] . Fluoride occurrence and concentrations in water resources (surface water and groundwater), depend on several contributing factors, such as pH, total dissolved solids, alkalinity, hardness and weathering of fluoride bearing rock forming minerals like muscovite, biotite, fluorite, fluoro-apatite etc [1] [9] - [11] .

However, in many countries worldwide, elevated fluoride concentrations are a result of fluorine polluted waste water discharges [12] - [15] . According to World Health Organization norms, the upper limit of fluoride concentration in drinking water is 1.5 mg/l [16] . Excessive presence of fluoride in water for drinking continues to be a serious public health concern in many parts of the world, including India. In India, this problem is common in states such as Andhra Pradesh, Tamilnadu, Karnataka, Kerala, Rajasthan, Gujarat, Uttar Pradesh, Punjab, Orissa as well as Jammu and Kashmir [17] . Many districts of Uttar Pradesh including Unnao, Agra, Mathura, Ghaziabad, Pratapgarh and Aligarh are facing the problem of inland salinity and excessive fluoride in groundwater [18] [19] .

Raebareli is one of the districts of Uttar Pradesh state in India. The land area of this district is traversed by two rivers namely Ganga and Sai. The groundwater of this district is not safe because it is contaminated with fluoride, arsenic and coliform bacteria. The fluoride level in some of the villages within the of Raebareli District, the fluoride concentration is as high as 4.2 mg/l, which implies that the villagers are at high risk of developing severe, adverse health effects [20] . Arsenic (As) is also found in different parts of “Rae Bareli” district with concentration more than WHO permissible limit (0.01 ppb). Even few blocks have arsenic contamination more than 0.05 ppb. Homemade bio-sand filter is one of the options for the removal of fluoride, arsenic and coliform bacteria and this is also economical to construct, operate and maintain [21] .

Several defluoridation technologies of drinking water, such as ion exchange [22] , precipitation-coagulation [23] , reverse osmosis [24] , electro dialysis [25] and nano filtration, have been developed for fluoride removal from water [26] . Ion exchange is a reliable and simple way to remove fluoride from water while its selective up-taking for fluoride is usually not so satisfactory for water because of the coexisting anions such as sulphate, carbonate, phosphate and hydroxide in the drinking water. These anions may impede the effective stabilization of fluoride onto the resins [27] . Precipitation-coagulation process is a good way to remove fluoride from the water [28] , for its easy operation, low cost and extensive application, while one of its dominant disadvantages is its difficulty to decrease the equilibrium concentration of fluoride in water below the allowable limit level regulated by WHO, hence it can only be employed as one of the primary unit operations in the practical water treatment. Moreover, the produced mud still has the potential to cause secondary pollution and hazard. As for other methods, such as reverse osmosis [29] , electrodialysis [30] , and nanofiltration [31] , they exhibit excellent purification capacity for fluoride removal, but expensive operation cost also limits their extensive application, especially for the wide countryside areas.

In comparison, adsorption is one of the most popular purification methods due to its high selectivity, low cost, high efficiency and easy post-treatment after adsorption. Recently, a series of low-cost adsorbents derived from agricultural waste or natural materials [32] [33] have been investigated for toxic substances like fluoride removal from aqueous solutions, such as apple and orange juicing residue, waste tea, peanut hull, rice straw, and coconut shell. Several adsorbents especially for the removal of fluoride anion from the aqueous solution have been developed, namely activated alumina, bone char, calcite, clay, zeolite, rare metal-loaded resins, etc. [34] [35] Activated alumina is quite effective for the removal of fluoride, while the leaked Al3+ in the drinking water may bring about senile dementia for people. Bone char is usually applied to the purification of fluoride and arsenic, but the source of this material is not so abundant. As for calcite, clay and zeolite, their cost-effectiveness still needs to be improved. In contrast to these above-mentioned adsorbents, the rare metal loaded adsorbents exhibit fairly good adsorption properties for their selective affinity to fluoride anion, high adsorption capacity, easy operation and harmless characteristic, and draw the interests of more and more researchers. For this kind of adsorbent, it is significant to choose the suitable matrix materials used for loading of rare metals and consequently affect the adsorption behaviour for fluoride anion directly.

The biomass produced in the agricultural industry is one of the most promising candidates for this application for its effectiveness, availability and abundance. In this aspect, orange juice residue has been used as the matrix material to load rare metal ions, showing quite excellent adsorption properties for anions including fluoride, arsenic and phosphate [36] [37] . While for the wide application of this technique, more biomass should be sieved to develop highly cost-effective adsorbents in fluoride purification.

In this study, a bio-adsorbent CPGC was developed for fluoride removal with a kind of easily available biowaste, Pomegranate seeds, which can be an alternative to the costly de-fluoridation products such as ion exchange resins and electro dialysis. In India, 810 × 103 metric ton Pomegranate fruit is consumed every year, and lots of seed waste is disposed, causing a severe problem in the community. So, for the environmental interest, this bio-waste could be a low-cost adsorbent and remove fluoride from groundwater. The aim of the present study is to evaluate the feasibility of using pomegranate seed waste for fluoride removal from groundwater and the effect of common experimental parameters, such as the initial pH value of the solution, equilibrium concentration of fluoride, contact time, adsorbent dose and coexisting anions.

2. Experimental Methods

2.1. Adsorbent Preparation

The Punica granatum seed (powdered sample), common name, Pomegranate, was purchased from market. Then the material was dried at 378 - 383 K for 24 hours. It was washed with doubly distilled water to remove the free acid and dried at the same temperature for 3 hours. Later, the dried adsorbent was carbonised thermally in Muffle furnace between 1073 K to 1084 K temperature ranges. The resulting product was cooled to room temperature and sieved to the desired particle sizes, namely, <55, 55 - 106, 106 - 150, 150 - 225 and 225 - 305 micron. Finally, the product was stored in vacuum desiccators until required for treatment. The physiochemical properties of the adsorbent are listed in Table 1.

2.2. Batch Adsorption Study

The batch adsorption de-fluoridation study was conducted for the optimization of various experimental conditions like contact time, initial fluoride concentration, adsorbent dose, particle size and influence of co-ions with fixed dosage. The mixture was agitated in a thermostatic shaker at a speed of 250 rpm at room temperature. The reagents used in this present study are of analytical grade. A fluoride ion stock solution (100 mg/l) was prepared and other fluoride test solutions were prepared by subsequent dilution of the stock solution. Analytical grade sodium chloride, sodium nitrate, sodium sulphate and sodium phosphate were used to prepare 1.0 mol/L stock solutions, and mixed at an arbitrary volume ratio to adjust the concentration of the coexisting anions in the solution. Analytical grade sodium citrate and sodium nitrate were employed to prepare the total ion strength adjusting buffer (TISAB) solution for the pre-treatment of all sampling solutions before testing by using ion selective electrode of fluoride.

All the experiments were carried out at room temperature. Fluoride ion concentration was measured with a specific ion selective electrode by use of total ionic strength adjustment buffer II (TISAB II) solution to maintain

Table 1. The physicochemical properties of CPGC adsorbent.

pH 5 - 5.5 and to eliminate the interference effect of complexing ions [38] . The pH of samples was measured by Orion ion selective equipment. All other water quality parameters were analyzed by using standard methods [39] . Effect of different initial fluoride concentrations viz., 2, 4, 6, 8 and 10 mg/l were studied by keeping the mass of sorbent at 0.75 g and volume of solution at 100 ml in neutral pH.

The fluoride concentration retained in the adsorbent phase, qe (mg/g), is calculated by Equation (1).

(1)

where qe is the amount of fluoride adsorbed (mg/g); V is the volume of solution; co and ce are the initial and residual concentration at equilibrium (mg/l), respectively, of fluoride and W is the weight (g) of the adsorbent.

3. Results and Discussion

3.1. Effect of Contact Time and Initial Fluoride Concentration

Contact time plays a very important role in adsorption dynamics. The effect of contact time on adsorption of fluoride onto CPGC is shown in Figure 1. Batch adsorption studies using the concentrations 2, 3, 4, 6, 8 and 10 mg/l of fluoride solution with 0.75 g of the adsorbent were carried out at 298 K as a function of time to evaluate the de-fluoridation and adsorption rate constants. The adsorption of fluoride increases with time and gradually attains equilibrium after 75 minutes. From Figure 1, the time to reach equilibrium conditions appears to be independent of initial fluoride concentrations. Therefore, 75 minutes was fixed as minimum contact time for the maximum de-fluoridation of the sorbent. The adsorption of fluoride decreased from 88% to 47% by increasing fluoride concentration from 2.0 to 10.0 mg/l. Further, it was observed that the removal curves are smooth and continuous indicating the possibility of the formation of monolayer coverage of fluoride ion at the interface of adsorbent.

3.2. Effect of Particle Size

The de-fluoridation experiments were conducted using CPGC with five different particle sizes viz. 55, 55 - 106, 106 - 150, 150 - 225 and 225 - 303 μm. As the adsorption process is a surface phenomenon, the de-fluoridation efficiency of the sample with 55 μm registered high de-fluoridation efficiency due to larger surface area (Figure 2). The variation in the percentages of fluoride removal by the sample with different particle sizes was studied. Hence, the material with particle size of 55 μm has been chosen for further experiments. Higher percentage of adsorption by CPGC with smaller particle size is due to the availability of more specific surface area on the adsorbent surface.

3.3. Effect of Adsorbent Dose

One of the parameters that strongly affect the adsorption capacity is the concentration of the adsorbents. The effect

Figure 1. Effect of contact time and fluoride concentration on fluoride removal.

of adsorbent dosage on the removal of fluoride from ground water was studied at neutral pH and fluoride concentration of 3 mg/l for 150 min. Figure 3 indicates that, increasing adsorbent dosage increases fluoride uptake, indicating that for a fluoride removal an optimum CPGC dosage of 0.75 g/L was required. The results further illustrates that the fluoride removal efficiency increases up to this optimum dosage beyond which fluoride uptake has no significant change with CPGC dosage. The increase in the adsorbent dosage provides greater surface area and hence increases the adsorption. However, by increasing the adsorbent dosage beyond the optimum dosage, there may be a slight improvement in fluoride removal efficiency but the adsorption capacity decreases.

3.4. Effect of Interfering Co-Ions

The effects of coexisting anions such as sulphate, nitrate, chloride and bicarbonate on fluoride adsorption by the CPGC adsorbent were examined and the results are given in Figure 4.

Chloride and nitrate did not perceptibly interfere with fluoride removal even at a concentration of 500 mg/l, while sulphate began to show some adverse effects when the concentration increases. However, bicarbonate showed great competitive adsorption with fluoride. The fluoride adsorption amount decreased quickly from 78.1 to 52% with the increase of bicarbonate concentration 0 - 500 mg/l. This may be attributed to the competition of bicarbonate ions with the fluoride ions at the active site, on the surface of the sorbents. The selective nature of the fluoride by the sorbent depends on size, charge, polarizability, electro negativity difference, etc. The order of interference for fluoride removal was in the following order, > > Cl > for the adsorbent CPGC.

3.5. Adsorption Isotherms

The sorption isotherms express the specific relation between the concentration of sorbate and its degree to

Figure 2. Effect of particle size on fluoride removal.

Figure 3. Influence of adsorbent dose on de-fluoridation.

accumulation onto sorbent surface. The fluoride sorption capacity of CPGC at 298 K was evaluated using Langmuir and Freundlich isotherm models.

The experimental data was applied in accordance with the linearized form of the Langmuir isotherm model. It can be represented as Equation (2):

(2)

where qm is qe for a complete monolayer (mg/g); Ka is the adsorption equilibrium constant (cm3/mg). To evaluate the adsorption capacity for a particular range of adsorbate concentration, the aforementioned equation can be used in the following linear Equation (3):

(3)

The constants qm and Ka in Equation (2) can be determined from the slope and intercept of the linear plot/graph of ce/qe versus ce in Figure 5. Results indicate that the adsorbent CPGC has a high affinity for fluoride adsorption under these conditions. The present data fit well in Langmuir isotherm model with R2 > 0.970. The average monolayer adsorption capacity (qm) obtained for CPGC is 1.68 mg/g.

Freundlich adsorption isotherm is based on adsorption on heterogeneous surface, and is the earliest known relationship describing the adsorption equilibrium and is given as Equation (4):

Figure 4. Variation in adsorption capacity for different concentrations of co-ions.

Figure 5. Langmuir isotherm for fluoride adsorption at various temperatures.

Figure 6. Plot of Freundlich isotherm for fluoride adsorption on CPGC.

(4)

where x is the amount of solute adsorbed (mg), m is the mass of adsorbent used (g), Kf and 1/n are empirical constants, indicating the adsorption capacity and adsorption intensity, respectively. Above Equation (4) may be converted to a linear form (5) by taking logarithms:

(5)

The values of Kf and 1/n were obtained from the slope and intercept of the plot between log(qe) and log(ce). The Freundlich equation deals with physicochemical adsorption on heterogeneous surfaces. Linearized form of the Freundlich equation is demonstrated in Figure 6. Adsorption data fitted well in linearized form of model equation (R2 > 0.980) which indicated the acceptability of the model.

4. Conclusion

Among various bio-waste materials, Punica granatum seeds were first time utilised in de-fluoridation of ground- water. In the present study, the fluoride is removed from aqueous solutions using Carbonised Punica granatum Carbon (CPGC) seeds as bio-adsorbent. It can be concluded that CPGC has good properties for the sorption of fluoride ions from aqueous solutions. The equilibrium time for removal of fluoride concentration is determined to be 75 min. The fluoride saturation capacity of CPGC is 1.68 mg F/g at room temperature. The best fitting adsorption isotherm is Freundlich model (R2 > 0.980), which indicates that fluoride bio-adsorption onto CPGC is characterized by chemisorptions on heterogeneous surfaces. The particle size is an important parameter that affects the sorption for fluoride on CPGC since the sorption of these ions increases as the particle size decreases. Finally, this low-cost material can be employed as an adsorbent for fluoride removal from groundwater, in particular in domestic systems where fluoride related problems exist.

References

  1. World Health Organization (WHO) (1984) Fluoride and Fluorides: Environmental Health Criteria 36. Geneva.
  2. World Health Organization (WHO) (2002) Fluorides―Environmental Health Criteria 227. Geneva.
  3. Viswanathan, G., Gopalakrishnan, S. and Siva Ilango S. (2001) Assessment of Water Contribution on Total Fluoride intake of Various Age Groups of People in Fluoride Endemic And Non-Endemic Areas of Dindigul District, Tamil Nadu, South India. Water Research, 44, 6186-6200. http://dx.doi.org/10.1016/j.watres.2010.07.041
  4. Yadav, A.K., Kaushik, C.P., Haritash, A.K., Singh, B., Raghuvanshi, S.P. and Kansal, A. (2007) Determination of Exposure and Probable Ingestion of Fluoride through Tea, Toothpaste, Tobacco and Pan Masala. Journal of Hazardous Materials, 142, 77-80. http://dx.doi.org/10.1016/j.jhazmat.2006.07.051
  5. Harrison, P.T.C. (2005) Fluoride in Water: A UK Perspective. Journal of Fluorine Chemistry, 126, 1448-1456. http://dx.doi.org/10.1016/j.jfluchem.2005.09.009
  6. Valdez-Jiménez, L., Soria Fregozo, C., Miranda Beltrán, M.L., Gutiérrez Coronado, O. and Pérez Vega, M.I. (2011) Effects of the Fluoride on the Central Nervous System. Neurología, 26, 297-300. http://dx.doi.org/10.1016/j.nrl.2010.10.008
  7. Browne, D., Whelton, H. and Mullane, D.O. (2005) Fluoride Metabolism and Fluorosis. Journak of Dentistry, 33, 177- 186. http://dx.doi.org/10.1016/j.jdent.2004.10.003
  8. Mandinic, Z., Curcic, M., Antonijevic, B., Carevic, M., Mandic, J., Djukic-Cosic, D. and Lekic, C.P. (2010) Fluoride in Drinking Water and Dental Fluorosis. Science of the Total Environment, 408, 3507-3512. http://dx.doi.org/10.1016/j.scitotenv.2010.04.029
  9. Karthikeyan, G. and Shanmugasundarraj, A. (2000) Isopleth Mapping and In-Situ Fluoride Dependence on Water Quality in the Krishnagiri Block of Tamil Nadu in South India. Fluoride, 33, 121-127.
  10. Kumar, S., Bharti, V.K., Singh, K.B. and Singh, T.N. (2010). Quality Assessment of Potable Water in the Town of Kolasib, Mizoram (India). Environmental Earth Sciences, 61, 115-121. http://dx.doi.org/10.1007/s12665-009-0326-8
  11. Singh, A.K., Raj, B., Tiwari, A.K. and Mahato, M.K. (2013) Evaluation of Hydrogeochemical Processes and Groundwater Quality in the Jhansi District of Bundelkhand Region, India. Environmental Earth Sciences, 70, 1225-1247. http://dx.doi.org/10.1007/s12665-012-2209-7
  12. Meenakshi, R.C. and Maheshwari, J. (2006) Fluoride in Drinking Water and Its Removal. Journal of Hazardous Materials, 137, 456-463. http://dx.doi.org/10.1016/j.jhazmat.2006.02.024
  13. Mourad, N.M., Sharshar, T., Elnimr, T. and Mousa, M.A. (2009) Radioactivity and Fluoride Contamination Derived from a Phosphate Fertilizer Plant in Egypt. Applied Radiation and Isotopes, 67, 1259-1268. http://dx.doi.org/10.1016/j.apradiso.2009.02.025
  14. Fan, C.S. and Li, K.C. (2013) Production of Insulating Glass Ceramics from Thin Film Transistor-Liquid Crystal Display (TFT-LCD) Waste Glass and Calcium Fluoride Sludge. Journal of Cleaner Production, 57, 335-341. http://dx.doi.org/10.1016/j.jclepro.2013.06.002
  15. Ponsot, I., Falcone, R. and Bernardo, E. (2013) Stabilization of Fluorine-Containing Industrial Waste by Production of Sintered Glass-Ceramics. Ceramics International, 39, 6907-6915. http://dx.doi.org/10.1016/j.ceramint.2013.02.025
  16. World Health Organization (2008) Guidelines for Drinking-Water Quality. WHO, Geneva.
  17. Susheela, A.K. (1999) Fluorosis Management Programme in India. Current Science, 77, 1250-1256.
  18. CGWB (2010) Groundwater Quality in Shallow Aquifers of India. Central Ground Water Board, Faridabad, 117.
  19. Tiwari, A.K. and Singh, A.K. (2014) Hydrogeochemical Investigation and Groundwater Quality Assessment of Pratapgarh District, Uttar Pradesh. Journal of the Geological Society of India, 83, 329-343. http://dx.doi.org/10.1007/s12594-014-0045-y
  20. Kanaujia, S., Singh, B. and Singh, S.K. (2013) Mapping of Fluoride Endemic Areas in Rae Bareli District, U.P., India. Chemical Science Transactions, 2, 1411-1417. http://dx.doi.org/10.7598/cst2013.539
  21. Kanaujia, S., Singh, B. and Singh, S.K. (2015) Novel Environmentally Benign Technique for the Removal of Fluoride, Arsenic and Coliform from Waste Water. International Journal of Sciences: Basic and Applied Research, 19, 88-96.
  22. Liu, R.X., Guo, J.L. and Tang, H.X. (2002) Adsorption of Fluoride, Phosphate, and Arsenate Ions on a New Type of Ion Exchange Fiber. Journal of Colloid and Interface Science, 248, 268-274. http://dx.doi.org/10.1006/jcis.2002.8260
  23. Turner, B.D., Binning, P. and Stipp, S.L.S. (2005) Fluoride Removal by Calcite: Evidence for Fluorite Precipitation and Surface Adsorption. Environmental Science & Technology, 39, 9561-9568. http://dx.doi.org/10.1021/es0505090
  24. Ghosh, D., Sinha, M.K. and Purkait, M.K. (2013) A Comparative Analysis of Low-Cost Ceramic Membrane Preparation for Effective Fluoride Removal Using Hybrid Technique. Desalination, 327, 2-13. http://dx.doi.org/10.1016/j.desal.2013.08.003
  25. Menkouchi Sahli, M.A., Annouar, S., Tahaikt, M., Mountadar, M., Soufiane, A. and Elmidaoui, A. (2007) Fluoride Removal for Underground Brackish Water by Adsorption on the Natural Chitosan and Electrodialysis. Desalination, 212, 37-45. http://dx.doi.org/10.1016/j.desal.2006.09.018
  26. Mohapatra, M., Anand, S., Mishra, B.K., Giles, D.E. and Singh, P. (2009) Review of Fluoride Removal from Drinking Water. Journal of Environmental Management, 91, 67-77. http://dx.doi.org/10.1016/j.jenvman.2009.08.015
  27. Meenakshi, S. and Viswanathan, N. (2007) Identification of Selective Ion-Exchange Resin for Fluoride Sorption. Journal of Colloid and Interface Science, 308, 438-450. http://dx.doi.org/10.1016/j.jcis.2006.12.032
  28. Sujana, M.G., Thakur, R.S., Das, S.N. and Rao, S.B. (1997) Defluorination of Waste Waters. Asian Journal of Chemistry, 9, 561-570.
  29. Greenlee, L.F., Desmond, F.L., Freeman, B.D., Marrot, B. and Moulin, P. (2009) Reverse Osmosis Desalination: Water Sources, Technology, and Today’s Challenges. Water Research, 43, 2317-2348. http://dx.doi.org/10.1016/j.watres.2009.03.010
  30. Kabay, N., Arar, O., Samatya, S., Yuksel, U. and Yuksel, M. (2008) Separation of Fluoride from Aqueous Solution by Electrodialysis: Effect of Process Parameters and Other Ionic Species. Journal of Hazardous Materials, 153, 107-113. http://dx.doi.org/10.1016/j.jhazmat.2007.08.024
  31. Simsons, R. (1993) Trace Element Removal from Ash Dam Waters by Nanofiltration and Diffusion Dialysis. Desalination, 89, 325-341. http://dx.doi.org/10.1016/0011-9164(93)80145-D
  32. Dhakal, R.P., Ghimire, K.N. and Inoue, K. (2005) Adsorptive Separation of Heavy Metals from an Aquatic Environment Using Orange Waste. Hydrometallurgy, 79, 182-190. http://dx.doi.org/10.1016/j.hydromet.2005.06.007
  33. Demirbas, A. (2008) Heavy Metal Adsorption onto Agro-Based Waste Materials: A Review. Journal of Hazardous Materials, 157, 220-229. http://dx.doi.org/10.1016/j.jhazmat.2008.01.024
  34. Alagumuthu, G. and Rajan, M. (2010) Equilibrium and Kinetics of Adsorption of Fluoride onto Zirconium Impregnated Cashew Nut Shell Carbon. Chemical Engineering Journal, 158, 451-457. http://dx.doi.org/10.1016/j.cej.2010.01.017
  35. Leyva-Ramos, R., Rivera-Utrilla, J., Medellincastillo, N.A. and Sanchez-Polo, M. (2010) Kinetic Modeling of Fluoride Adsorption from Aqueous Solution onto Bone Char. Chemical Engineering Journal, 158, 458-467. http://dx.doi.org/10.1016/j.cej.2010.01.019
  36. Biswas, B.K., Inoue, K., Ghimire, K.N., Ohta, S., Harada, H., Ohto, K. and Kawakita, H. (2007) The Adsorption of Phosphate from an Aquatic Environment Using Metal-Loaded Orange Waste. Journal of Colloid and Interface Science, 312, 214-223. http://dx.doi.org/10.1016/j.jcis.2007.03.072
  37. Biswas, B.K., Inoue, K. and Ghimire, K.N. (2008) Removal and Recovery of Phosphorus from Water by Means of Adsorption onto Orange Waste Gel Loaded with Zirconium. Bioresource Technology, 99, 8685-8690. http://dx.doi.org/10.1016/j.biortech.2008.04.015
  38. Chauhan, V.S., Dwivedi, P.K. and Iyengar, L. (2007) Investigations on Activated Alumina Based Domestic Defluoridation Units. Journal of Hazardous Materials, 139, 103-107. http://dx.doi.org/10.1016/j.jhazmat.2006.06.014
  39. American Public Health Association (2007) Standard Methods for the Examination of Water and Wastewater. 14th Edition, American Public Health Association, Washington DC.