[1]
|
B. J. Baliga, “Fundamentals of Power Semiconductor Devices,” Springer-Verlag, Berlin, 2008.
|
[2]
|
H. Lu, W-S. Loh, T. Tilford, et al., “Reliability of Power Electronic Modules,” InterPACK Conference American Society of Mechanical Engineers, New York, 8-11 July, 2007, pp. 883-888.
|
[3]
|
S. Ramminger, N. Seliger and G. Wachutka, “Reliability Model for Al Wire Bonds Subjected to Heel Crack Failures,” Microelectronics Reliability, Vol. 40, No. 8-10, 2000, pp. 1521-1525.
|
[4]
|
O. Usui, H. Muto and T. Kikunaga, “Evaluation of Temperature Distribution of a Power Semiconductor Chip Using Electrothermal Simulation,” IEEJ Transactions on Industry Applications, Vol. 124, No. 1, 2003, pp. 108- 115.
|
[5]
|
M. Ishiko, M. Usui, T. Ohuchi and M. Shirai, “Design Concept for Wire-bonding Reliability Improvement by Optimizing Position in Power Devices,” Microelectronics Reliability, Vol. 37, No. 3, 2006, pp. 262-268.
|
[6]
|
M. O'Keefe and A. Vlahinos, “Impacts of Cooling Technology on Solder Fatigue for Power Modules in Electric traction Drive Vehicles,” 2009 IEEE Vehicle Power and Propulsion Conference, Michigan, 7-10 September 2009, pp. 1182-1188.
|
[7]
|
X. Xie, X. Bi and G. Li, “Thermal-mechanical Fatigue Reliability of PbSnAg Solder Layer of Die Attachment for Power Electronic Devices,” International Conference on Electronic Packaging Technology & High Density Packaging, Beijing, 10-13 August 2009, pp.1181-1185.
|
[8]
|
L. J. Ladani, “Reliability Estimation for Large-Area Solder Joints Using Explicit Modeling of Damage,” Device and Materials Reliability, IEEE Transactions, Vol. 8, No. 2, 2008, pp. 375-386.
|
[9]
|
W. D. Zhuang, P. C. Chang, F. Y. Chou and R. K. Shiue., “Effect of Solder Creep on the Reliability of Large Area Die Attachment,” Microelectronics Reliability, Vol. 41, No. 12, 2001, pp. 2011-2021.
|
[10]
|
H. Ye, M. H. Lin and C. Basaran, “Failure Modes and FEM Analysis of Power Electronic Packaging,” Finite Elements in Analysis and Design, Vol. 38, No. 7, 2002, pp. 601-612.
|
[11]
|
Y. Nagatomo, T. Nagase and S. Shimamura, “FEM An- alysis of Thermal Cycle Properties of the Substrates for Power Modules,” Journal of Japan Institute of Electronics Packaging, Vol. 3, No. 2, 2000, pp. 330-334.
|
[12]
|
T. Matsunaga and S. Sudo, “Evaluation of Fatigue Life Reliability and New Lead Bonding Technology for Power Modules,” Mitsubishi Electr. Adv., Vol. 113, No. 5, 2006, pp. 13-16.
|
[13]
|
K. Shinohara and Q. Yu, “Fatigue Evaluation of Power Devices,”, International Conference on Electronic Pack- aging Technology & High Density Packaging, 10-13 August 2009, pp. 1277-1283.
|
[14]
|
O.C. Zienkiewicz and R.L. Taylor, “The Finite Element Method,” Butterworth-Heinemann, Oxford, 2005.
|
[15]
|
A. Tanaka, Q. Yu, T. Shibutani, Y. Kobayashi and M. Shiratori, “Low Cycle Fatigue Reliability Evaluation of Lead-free solders,” Nippon Kikai Gakkai Zairyo Rikigaku Bumon Koenkai Koen Ronbunshu, 2005, pp. 475-476.
|
[16]
|
The Society of Materials Science, “Factual Database on Creep and Creep-Fatigue Properties of Sn-37Pb and Sn-3.5Ag Solders,” The Society of Materials Science, Japan, 2004.
|
[17]
|
H. Iwasaki, K. Hisano and T.Takamatsu, “Thermal Prolem of Next Generation Semiconductor Power Devices,” Nippon Kikai Gakkai Nenji Taikai Koen Ronbunshu, Vol. 6, 2003, pp. 251-252.
|