New Method of Thermal Energy — To Electrical Energy Conversion in Vacuum Devices with the Metal — Dielectric Nanofilm Electron Sources

New method of thermal energy—to electrical energy conversion in vacuum devices with the metal (W)—dielectric nanofilm (ZrO2) electron source is offered and studied. According to estimates and results of modeling, the energy effectiveness (χ) of the proposed method may exceed χ for the known thermionic energy conversion method to 2 3 orders of magnitude.


Introduction
Achievements of last decades in the area of micro-and nanotechnology promoted revival of scientific interest to a problem of direct transformation of thermal energy to electrical energy.As a result of development of nanotechnology methods, researchers had new possibilities for use in the workings out of the fundamental physical phenomena which remained earlier not claimed.In particular, reproduced formations of quasi 1D and 2D nanostructures (NS) have allowed to start working out on the thermionic energy conversion devices with the single-crystal n-type diamond electron sources (cathodes) [1].
The main aim of this work is to, on the basis of new ideas about the mechanism of the abnormal thermal field emission from the metal-dielectric nanofilm structures [2], propose and justify the opportunity to design an original and more energy effective method compared to known thermionic energy conversion (TEC) method [3].
It should be noted that converting thermal energy to electrical power in the themionic converter (TC) is achieved by electron emission and passing of an electron current from the emitter to the collector in the electrostatic field produced by a contact potential difference between electrodes (emitter and collector).Figure 1 shows the energy diagram that makes it easy to understand (or remember) the known principle of TC action.
At present the TEC method is developed in a sufficient measure [3].This method permits implementation of the energy conversion (EC) process with the efficiency η ~ 20% and the energy effectiveness (χ) ( ) where J S -saturation thermionic current density for the emitter substance; Φ e , Φ c -work function (in eV) of the emitter and collector TC, respectively, about As is known [3], TEC method has two major drawbacks.
First or technical-technological disadvantage is the need to have heated to high temperatures (~2000 K) TC electrodes at very small distances.Physically small size of the vacuum gap is determined by the strong influence of the thermionic electrons space charge (SC) field on the TC conductivity [3].The second fundamental flaw of this method is that the saturation current density of the TC effective emitters is only about ~10 A/cm 2 .An analysis of literature data [4] should be that, to date, the potential for further development of the TEC method is largely exhausted and the substantial improvement in its technical and operational V. E. Ptitsin specifications may only as a result of significant changes in the physical basis of this method.At first glance, to correct the above deficiencies of the TEC method possible to try to create a new vacuum device for energy conversion, in which thermionic cathode would be replaced by a thermal field electron emitter with high emission current density (up to ~10 8 A/cm 2 [5]).In addition, as shown in a work [6] the influence of space charge (SC) field on the thermal field emission (TFE) process very low and, therefore, to effectively transfer the emitted electron flow to the device collector is no longer required to bring the electrodes to a very small value vacuum gap (<100 µm).

Physical Simulation of the Vacuum Thermal-to-Electrical Energy Converter Prototype with High Energy Effectiveness
For creation of the vacuum energy conversion device prototype with high energy effectiveness, it is clear that electront source of the created converter should have high emission capacity.At the beginning of our research, we assumed that for this purpose can be used high current density TFE electron source.It is essential that this electron source and electron-optical system (EOS) of the new energy conversion device prototype must satisfies a number of obvious physical conditions.
1) Emitting surface of the device electron source (cathode) should have high curvature.As the cathode can be used a single microtip or also an ordered ensembles of the microtips, quantum dots, and carbon nanotubes.
2) In such device must be running condition for physical "separation" of the two interrelated processes-electron emission and electron transport processes.
To realize this condition was proposed to introduce in the traditional thermionic converter diode system additional extracting electrode that allow create on the structured cathode surface necessary high electric field (up to ~10 7 V/cm).Additional extracting electrode allows create necessary conditions for high intensity e-flux emission.For the subsequent transport of the e-flux from the cathode to the collector surface with a potential that approximately equal to contact potential difference (between the cathode and the convertor collector) it was suggested to use the known magnetic isolation method.Magnetic isolation allows prevent direct capture (or deposition) of an electrons by the extracting electrode under electrical field acting.
Phenomenological scheme of the emission and electron transport processes in the thermal-to-electrical energy converter prototype with nanostructured surface of TFE electron source is shown on Figure 2. From Figure 2 of the phenomenological scheme, of course, impossible to understand whether the proposed approach physically reasonable.In order to ascertain the validity of the proposed schemes for energy conversion devices, you must first find out whether emitted an electron to reach the surface collector in the specified physical conditions.In other words, be sure that after extraction the electron moving in the EOS converter potential field, the energy conservation law will not be disturbed.For ease of analysis, it will assume that the cathode is a single metal (W) tip, that depending on the values of the T e and V ext can play the role of either thermionic cathode or thermal field emitter (cathode) as well as at low temperature T e the metal tip can be considered as a field emitter (cathode).Let also Φ e > Φ c .
In addition, we will consider the initial stage of each of the possible emission processes.That is, immediately after the inclusion of the extracting electrostatic field and the magnetic field.In this initial phase Fermi levels of the cathode and collector will still one and the same value on the energy scale.Taking into account the comments made above, Figure 2 can be represented in a more informative (space-energy) form (see Figure 3).
For clarity, we will assume that the field strength at the W emitter surface is sufficient for field electron emission and the emitter temperature can vary widely from 300 K to 2500 K.
In order to qualitatively to provide processes that must occur in the proposed version of the EOS converter will be based on three known fundamental physical principles.
1) In contact two or more solid bodies the Fermi levels of these bodies take the same value.
2) When charge move in a potential force field the total energy of the charge remains constant.
3) In a result of an electron tunneling from the metal in vacuum it total energy does not change.
At relatively low temperatures (<500 K) in this conversion device the dominant emission process is the process of field emission (FE).In these circumstances, electron emitted in vacuum by the tunnel mechanism, after acceleration will be reflected from the barrier: vacuum-collector.In these conditions, reach Thus, according to the qualitative analysis, the shift from the traditional EOS of the TI converter on proposed here EOS with three electrodes, gives no reason to believe that such a move could allow any significantly improve χ of the new type converter due to the contribution in energy conversion process intensive flows of FE and TFE electrons.
However, it is important to note that the offered EOS allows significantly increase the gap between the emitter and collector of electrons, and make it quite acceptable (more than ~(1 -5) cm) for prolonged use of the TC at high temperatures.
Another very important conclusion that follows from the previous review is that in order to improve the energy efficiency of thermal energy converter in electric energy it is necessary that electron source converter emitted in vacuum high intensity electron flux with full initial electron energy E, which would substantially exceed the height barrier: vacuum-collector (Figure 3).It is clear that such a "hot" electrons flow without dissipation at this barrier can freely inject into collector.In the next section it is shown that the required emission properties have some metal-nanofilm structures (W/ZrO 2 , Mo/ZrO 2 ) [2].

Abnormal Thermal Field Emission Electron Sources for Thermal to Electrical Energy Converters
More than ten years ago the author of this work, in the research of high-current electron sources has been found that W/ZrO 2 metal-nanofilm (MNF) structure at under certain conditions has unique emission properties [2].It has been revealed that in relatively low macroscopic (external) electrical fields (below ~500 V/μm) and at the material temperatures within 1950 K to 2150 K the MNF shows an abnormally high normalized brightness (up to ~10 6 A/(cm 2 sr V)) and high stability of field emission properties.The revealed phenomenon of a sharp rise in emissive ability of the W/ZrO 2 in a certain range of ZrO 2 layer thicknesses and substance temperatures was called "Abnormal Thermal Field Emission" (ATFE).A phenomenological model of the physical mechanism of the ATFE from planar MNF surfaces was developed.The opportunity of use of found out and investigate unique thermal field emission properties W/ZrO 2 structures in high current density electron sources and in energy conversion devices was offered and discussed in [7].
The phenomenological model of the ATFE phenomenon is constructed on the basis of generalization of the data obtained in the present study of field emission properties of low-dimensional nanostructures [2].
These data, in particular, show that specific features (or anomalies) of the process of field emission from the surface of such NS are substantially defined by physicochemical and structural properties of the superficial nanofilm which usually represents nanostructure consisting of metal or semi-conductor substrates and a thin dielectric layer.The thin dielectric nanofilm on the surface of the substrate is created is artificially by means of modern technological methods or is formed naturally as a result of oxidation of the substrate surface.Taking into account these remarks, to construction the model of ATFE from the surfaces of low-dimensional nanostructures in a real vacuum diode was modeled by a 2D structure: metal-a thin dielectric nanofilm placed into vacuum under a homogeneous electrostatic field of strength F e (Figure 4).
The ATFE model was based on the following assumptions [2].
1) Electron injection from metal to dielectric through the metal-dielectric interface, can involve both the thermal field emission and thermionic mechanisms; the metal-dielectric junction is locking for metal electrons; 2) Electric field on the metal-dielectric interface is a superposition: of external field (F e ), positive space charge (SC) field formed as a result of ionization of the localized states in the band gap of the dielectric film and also of SC field of electrons injected into the dielectric conduction band; 3) Ionization of the localized states in the band gap of the dielectric film may occur both by thermal field mechanism and, generally speaking, under action of the electromagnetic radiation absorbed by the film, including thermal radiation of the emitter substance; 4) At small thicknesses of a dielectric nanofilm (about the free path length of The results of the analytical modeling of ATFE were in good agreement with the experimental data [8].In particular, it was shown that the total ATFE current density can reach values ~10 8 A/cm 2 .The ATFE process and, consequently, emission current at the fixed MNF temperature and extracting voltage V ext values is characterized by high stability [9]. With regard to the subject of this work is also important to note the results of measurements of the energies distribution emitted electrons in ATFE process (Figure 5).As you can see from the electron energy distribution curve in the flow of the ATFE the relatively large number of electrons (~5% -10%) have a primary energy more ~4 eV.Physically, this means that if you use the ATFE emitter in the energy converter prototype (Figure 3) that ~(0.05 -0.10) ATFE flow will inject in the collector over the potential barier: vacuum-collector.According to estimates and results of numerical modeling [7], the power density of the "hot electrons" on the collector surface can reach high values, the order of ~(10 3 -10 4 ) W/cm 2 or higher.

Conclusions
Research shows that the energy effectiveness of the traditional TI energy conversion method can be significantly (to the 2 -3 orders of magnitude) increased through use in the new type energy converter with electron source based on the To create the necessary physical conditions, the EOS of a new type energy converter must contain (in addition to the emitter and collector) special third electrode-extractor.Additionally, the EOS should include the source of a uniform magnetic field that required for magnetic isolation of the emitted electron flux.
The results can be easily consolidated at a large electron emitting surfaces on which by the modern techniques of nanotechnology can be grown ordered ensembles of the quantum dots or nanowhiskers each of which acts as point electron emitter in the physical conditions needed for the ATFE process excitation.ATFE properties: super high emission ability and stability of process, rather low level of F e and also high density of emission current (up to 10 8 A/cm 2 and more) can be used in different areas of micro-and nanoelectronics, including high power electronics to produce high-intensity stationary electron sources and also in the area of energy transformation for development of effective systems for direct small-scale energy conversion devices requires portable electrical power to drive electronic components as well as a compact cooling system to maintain the temperature of the primary electronic components within a narrow range at or below ambient.Similar needs for efficient, small-scale cooling and/or power generation will persist for many future engineering applications.
The ATFE phenomenon relates generally to energy conversion devices, and more particularly, this phenomenon pertains to the use of W/ZrO 2 electron emitters in thermodynamic energy conversion devices.The need for efficient, reliable, and cost-effective small-scale energy conversion devices is increasing

Figure 1 .
Figure 1.Energy diagram showing the principle of the TC operation.Here Φ e , Φ c , T e , T c -work function and temperature of the emitter and collector TC, respectively.Is-saturation current at the emitter working temperature; z c (z c < 100 µm) is the optimal value of the gap between TC electrodes.Direct line (blue) corresponds to the potential distribution, if not to take into account the effect of SC field.

Figure 2 .
Figure 2. Phenomenological scheme of the emission and electron transport processes in the thermal-to-electrical energy converter prototype with nanostructured surface of the electron source; V ext -extracting voltage; B  -induction of a uniform magnetic field.

Figure 3 .
Figure 3. Phenomenological functional scheme of the different electron emission and transport processes in the thermal-to-electrical energy converter prototype with the single metal (W) tip as an electron source; abbreviations: TI-thermionic, FE-field emission, TFE-thermal field emission.

Figure 4 .
Figure 4.Two barrier energy band diagram for ATFE phenomenon theoretical modeling.

Figure 5 .
Figure 5.Typical curve for distribution of the ATFE electrons on the full initial energies in vacuum.