Environmental Impacts of Grid Connected High Concentrated Photovoltaic Systems Adapted for Peak Load Minimization in Hot Climate

High concentrated PV multi-junction solar cells (HCPV) likely present a favorable alternative to achieve low cost of energy. However, multi-junction solar cell has different characteristics which should be settled before they can be adapted for large scale energy generation. Peak energy consumption in Kuwait usually occurs in periods of utilizing air conditioning systems which are essentially used in almost all year around in harsh climate like Kuwait. Power consumed at peak times is more costly than power needed to satisfy loads at regular consumption times. The main goal of the present research is to increase HCPV solar cells’ efficiency, to decrease maximum power cost in Kuwait. Multi-junction solar cells performance in weather conditions of Kuwait is investigated employing a single diode equivalent circuit model. The model developed considers the impacts of concentration ratio as well as temperature. Most research in literature review usually neglects shunt resistance of the diode, however this resistance is taken into consideration in current developed theoretical model. To calibrate the present model, current predictions are compared with corresponding measured data provided by multi-junction solar cell manufacturer. The total root mean square errors in the present model predictions are about 1.8%. This means that current developed model of single diode model which takes into account shunt resistance impacts gives precise and reliable data. HCP electrical efficiency is noticed to rise as concentration increases but to a certain concentration value, then it begins to decrease. In addition, utilizing HCPV linked to grid satisfies great decrease in maximum load. Power produced from HCPV modules is utilized to provide energy needs to a family in normal Kuwaiti family home to evaHow to cite this paper: Alzanki, T.H., Kandil, K.M., Alenezi, M.R. and Ghoneim, A.A. (2018) Environmental Impacts of Grid Connected High Concentrated Photovoltaic Systems Adapted for Peak Load Minimization in Hot Climate. Smart Grid and Renewable Energy, 9, 237-258. https://doi.org/10.4236/sgre.2018.911015 Received: October 15, 2018 Accepted: November 26, 2018 Published: November 29, 2018 Copyright © 2018 by authors and Scientific Research Publishing Inc. This work is licensed under the Creative Commons Attribution International License (CC BY 4.0). http://creativecommons.org/licenses/by/4.0/


Introduction
Solar energy is a risk-free option to conventional fossil fuel that generates air pollution to our surroundings. Dangerous impacts of worldwide warming generated from traditional energy sources are also a significant issue in that matter. to dominating the PV market due to their reduced cost. Direct integration of III-V compound semiconductors on larger diameter, less costly and already available Si substrate is highly required for much less costly photovoltaic. Upgrading expensive PV solar cells by lower price optical materials results in a realistic cost saving [1] [2]. Focusing sunlight concentrated on the aperture of high efficiency, multi-junction PV solar cell can generate much higher power densities than traditional PV cells. This concept can be achieved by utilizing concentrating solar rays into small cell area through optical systems. This approach is commonly introduced as concentrator photovoltaic technology (CPV). It minimizes PV cell area while device light intensity improves by equivalent factor.
This approach is generally presented as concentrator photovoltaic technology (CPV).lent factor. A number of CPV providers have got working efficiencies of about 25% [3] [4]. In various sunshine areas, annually available power for tracking concentrator with two-axis is higher than total solar intensity supplied to systems utilizing flat plate collector [5]. geometric, optic, tracking, etc. [6] that are usually depending on the concentration ratio or factor "X". Concentration factor (X) is defined geometrically as the ratio of primary optical area (receiver) to the active cell area and optically as the intensity ratio or Suns. Suns are the ratio between the concentrated light that attains the cells and the available maximum solar radiation (1000 W/m 2 ). Depending on concentration factor X, the system can be classified as low concentration (X < 10 Suns), medium ( [18]. These kinds of techniques can significantly improve the efficiency of distribution system as well as minimizing transmission lines losses [19]. Mondol et al. [20] evaluated optimum inverter sizes in certain European areas based on system generation. Jung So et al. [21] compared the simulated efficiency of PV systems to the monitored PV performance. Outcomes revealed that it is essential to improve the currently established technology.
The impact of surface slope on performance of grid connected PV for maritime weather conditions was inspected by Mondol et al. [22] using simulations.
The monthly optimum collection angle that optimizes solar radiation deviates from 10˚ up to 70˚. Hamrouni et al. [23] examined PV system in both regular and disturbed systems. The plant examined comprises of solar modules and a three-phase inverter. The theoretical and experimental data suggested the control performance of grid connected PV system in both situations. The four parameter model [24] is generally employed for studying solar cells characteristics. Passos et al. [27] analyzed the visibility of solar hot water systems in Brazilian climate. In addition, they evaluated the influence of solar water heating in decreasing the peak load requirements in Brazil. They decided that implementing solar energy for domestic water heating is feasible in Brazil. In addition, they stated that the peak demand is constant even in extreme climate conditions. Experimental and numerical studies are presented by Stathopoulos et al. [28] to review the impact of phase change materials. The heat storage system is composed of paraffin plates fixed at heat exchanger. Furthermore, a numerical model was introduced implementing finite differences technique. Additionally, they recommended a preliminary control strategy demonstrating the capabilities of this system in peak load control. There is a significant increase in energy consumption in Kuwait particularly for air conditioning systems in summer time. To satisfy the ever-growing load demand, extra power plants are set up continuously in Kuwait. This obviously indicates the imperative requirements for renewable energy systems to provide most of the power consumption especially in peak load times. This clearly demonstrates the potential need of HCPV systems to displace significant portions of conventional energy resources.
Zhuk [29] et al. analyzed the price of controlling a variety of power plants.
Their study revealed that utilizing battery is feasible for small peak demand  [30] analyzed China's coal-fired power units ‫׳‬peak management with a comprehensive setup capacity and peak shaving process. They reported rules guidelines to manage the peak shaving problem and to guarantee sustainable enhancement of power system. Decrease of peak load in the Polish electrical power system is demonstrated by Werminski et al. [31].
They applied a decentralized active demand response system to decrease peak loads. The simulation outcomes revealed that adapting a decentralized active demand response system results in a considerable reduction in peak load. A novel system for heating, electricity generation and cooling using energy peak load shifting is recommended by Lv et al. [32]. A brand new strategy is established to inspect the economic feasibility of such technique. The results revealed that system functions professionally for minimal pressure conditions. The suggested system saves about 53.9% yearly. Nazi et al. [33] developed a model for peak load decrease based on building's thermal analysis. Outcomes demonstrated that lighting system and windows heat gain account for 71% of the building's heat gain and 40.2% reduction in cooling load can decrease total power consumption by about 47%.
In current research, single diode equivalent circuit model is developed to analyze multi-junction cells efficiency in Kuwait weather conditions considering the impacts of both temperature and concentration ratio. Furthermore, the shunt resistance of the diode that is normally ignored in the existing models is taken into consideration in the present developed numerical model. Model results are compared to reported measured data to assess its accuracy and durability. The model predictions agree well with reported measured data. The combined impacts of high incident radiation and temperature on HCPV efficiency in hot and extreme climate similar to Kuwait climate are analyzed. Grid connected high concentrated PV is recommended to decrease the peak demand in Kuwait. Transient simulation program [34] implemented to examine the performance of HCPV in Kuwait weather conditions. Various solar modules area and orientation are studied to accomplish maximum energy generation from grid connected HCPV system. Restored power from HCPV is adapted to supply the energy consumption of people in standard Kuwaiti house. Different PV slopes and areas are assessed to maximize yearly energy outcomes from HCPV system. Finally, the CO 2 emission conserved is determined to examine environmental impacts of high concentrated photovoltaic in Kuwait climate. To our knowledge this is the first study assessing grid connected high concentrated photovoltaic systems for peak load reduction in Kuwait climate.

Numerical Modeling
The numerical model outlining the solar modules efficiency must properly determine the change of solar module power with surrounding radiation and temperature. This model is previously discussed in detail [35]. In Solar cell production power is function of radiation intensity and temperature since it is a nonlinear Smart Grid and Renewable Energy power supply. Figure where I sc is the short circuit current, n is the diode ideality factor, (n i ), I o is the diode reverse saturation current, q is the electron charge, k the Boltzmann constant.
Cell output power reaches peak at maximum power point (MPP where I m and V m are maximum voltage and maximum current at maximum power P m . Proportion of solar cell output energy to energy input from sunlight is the most important criteria adapted to assess solar cell efficiency, η, and it is given by: The triple junction solar cell is composed of three junction linked in series.
Every junction expressed by the single diode model. I − V relation for cell junction considering the shunt resistance: , , Each sub cell specified using set of 5 factors: short circuit current (I sc ), diode ideality factor (n i ), diode reverse saturation current (I o,i ), series resistance (R s,i ), and shunt resistance (R sh,i ). The terminal voltage is V, q electron charge of the, Boltzmann constant, k B , J i is load current; T is cell temperature and represent cell junction (1 for top cell, 2 for medium cell and 3 for top cell). Reverse saturation current is the main factor influencing V oc , so I 0 , is a measure of minority carriers loss throughout p − n junction in reverse bias. Diode ideality factor, n, accounts for diffusion diode non-idealities. Based on Shockley theory of diodes, n should equal unity, but a value of n > 1 is more appropriate to include imperfections produced through manufacturing process. The series resistance is the sum of the bulk resistance of semiconductor materials, metal grids bulk resistance and interconnections and resistance contacting metal contact and the semiconductor.
The most significant factor in obtaining high efficiency concentrated solar cells is R s . Shunt resistance is caused by the leakage current across the p − n junction, either at cell perimeter or in the crystal close to the junction due to defects or deposition of impurities. Open circuit voltage (V oc ) is attained by setting I = 0 in Equation (6).
The last term in Equation (6) makes the equation, nonlinear and implicit needing outstanding computational attempts to be solved. That is the reason why the last term in Equation (6) is ignored in the published models considering the shunt resistance is infinity. This estimate can greatly impact the precision of the model predictions. So, shunt resistance is considered in the present work.
Using the Lambert W-function [36], Equation (6) Because of its explicit nature, Equation (7) has recently been adapted to analyze PV systems [38] [39]. Lambert W-function is solved using already mathe-Smart Grid and Renewable Energy matical software packages. In present study, Maple software is employed to conduct the calculations of the developed numerical model. To numerically solve Equation (7), five parameters should evaluated; n, I sc , I 0 , R s , and R sh . These factors have a significant role in the behavior of PV devices. The method carried out by Ghani et al. [40] is followed to determine these five parameters.
Summing the voltages of each subcell, multi-junction total voltage (V) is: For single diode model of multi-junction cell, 10 empirical factors are evaluated by calibration versus measurements. Dark saturation current density (I o,i ), current per unit cell area, is strongly temperature dependent and can be expressed as: where E g,I is energy and k and γ are constants. Recombination in both quasi state neutral and depletion region is utilized to model I o . Energy band gap decreases with temperature; so I sc increases with temperature. In spite of that, this change is usually ignored in reported models as the band gap is usually considered constant. This effect must be considered if high accuracy of cell performance over a broad range of temperatures is required. Solar cells working temperature in CPV system is much higher than surrounding temperature. So, temperature impact on cell performance is extremely significant for CPV system design considerations. The band gap energy of semiconductors decreases with increasing temperature as expressed by the empirical expression introduced by Grey et al. [41]:

Electricity Consumption in Kuwait
Energy consumption in Kuwait is increasing very rapidly at a rate of about 7%

Load Data Analysis
The load each hour is calculated at 30 minutes steps throughout the period from 1960 to 2016. The load for each 30 minutes is recorded and analyzed by a program model. In hot months (June-September), a significant increase in energy consumption is noticed. This is due to the increase in AC load through summer months. It is worthy to point out that in summer, hourly load follow same order and at 15:00 hour the power reaches its maximum value. Figure 3 shows the Year Smart Grid and Renewable Energy

System Components
In addition to HCPV modules, PV systems need batteries, system wiring, inverters, support structures, over current protection and disconnects switches. In- fuses. Grid connected system is suggested for the present work. In this situation, batteries are not necessary as power from grid utilized to supply power if required power is greater than the power produced by PV system. In addition, PV system generally necessitate maximum power point tracker [43] to control PV outputs so it continuously runs close to maximum power point. Figure 4 illustrates the proposed system adapted for the present study.

Methodology
The goal of present study is to examine the capability of high concentrated PV modules to minimize total and peak power in Kuwait. The targeted load decrease is affected by HCPV performance in addition to the instantaneous occurrence of both HCPV output and peak load. The HCPV power is evaluated utilizing recorded hourly electrical loads and weather data for Kuwait. The single diode equivalent circuit model developed for this work is employed to calculate multi-junction cells performance in Kuwait climate taking into account the impacts of both temperature and concentration ratio. Transient simulation program [34] is adapted to evaluate HCPV system hourly energy output utilizing both ambient temperature and radiation incident on array surface. The HCPV system is assumed to be due south and inclined at a 31˚ (Kuwait latitude). TYPE 16 (solar radiation subroutine) built in TRNSYS is utilized to evaluate angle of incident. Duffie and Beckman [44] suggested correlations are utilized to evaluate effective angle of incident. Each simulation has a one year period and utilize gallium indium phosphide/gallium indium arsenide/germanium (GaInP/GaInAs/Ge) triple junction Azurspace cells [45]. Grid connected HCPV energy output greatly ruled by the location weather data. A FORTRAN code is introduced to create hourly weather data from available monthly data for surrounding temperature and horizontal radiation. Weather data employed in this work have been monitored and recorded for five years in the College of Technological Studies, Kuwait. A specific model is developed to calculate hourly loads then address the load style to a data file.

Environmental Life Cycle Assessment
If a PV power facility (low or non CO 2 emitting plant) is established as an alternative to conventional power plant (higher CO 2 emitting plant), this will definitely results in a reduction of CO 2 emission. Avoided CO 2 emission is the difference between emissions generated by conventional energy sources and the ones generated throughout the manufacture of PV through entire system duration (25 years). Spiegel et al. [46] examined offset potential of the pollutant emission for distributed photovoltaic plant. Power generated used to determine offset emissions of SO 2 , CO 2 , and NO x . The emission decrease of greenhouse gases are evaluated by Delarue et al. [47] at different European regions. They mentioned that greenhouse gases emission reduction in power generated may accomplish a value of 19%.
In current study, a numerical model is introduced to determine avoided CO 2 emission achieved due to the utilization of grid-connected HCPV system. Grid connected HCPV system is suggested to provide electricity consumption demands (lighting and household appliances) for people in an standard Kuwaiti house. The emissions produced in the fabrication procedures of PV systems can be disregarded [48] since they are substantially lower than the emissions produced by conventional sources. Avoided CO 2 emission is primary the CO 2 emissions that generated by traditional sources. To carry out CO 2 emission reduction computations for PV, the reference case of the electricity system must be specified. This of course will require identifying the conventional source and associated fuel (oil, natural gas, coal). The standard emission parameters as well as conversion efficiencies of a variety of fuel types [49] are input to the model.

Results and Discussions
The data used for the present study is measured and recorded by the outdoor test facility set up at College of Technological Studies, Kuwait (Latitude 31˚). The weather data include continuous measurements of hourly surrounding temperature, solar global radiation and solar direct radiation on horizontal surface at Kuwait for five years in the period from 1 st October 2011 till 31 st Septmber 2016. The HCPV module adapted to conduct current work and to calibrate predictions of present developed model is: gallium indium phosphide/gallium indium arsenide /germanium (GaInP/GaInAs/Ge) triple-junction data of Azurspace 2016. Predicted parameters for Azurspace cells using present single diode model is presented in Table 1. for the HCPV module studied. As seen, η increases with concentration until concentration factor equal to 400 approximately for Azurspace cells. This increase is controlled by V oc logarithmic increase with intensity. However, as concentration goes up, this effect is compromised by cell fill factor reduction because of losses in series resistance. Consequently, efficiency decreases over a specific concentration degree. The efficiency behavior follows the same trend in V oc , which agrees well with earlier results [50]. The root mean square error in efficiency calculation is found to be 1.8%. These results clearly indicate that the present model predictions for Azurspace cellagree well with the corresponding experimental data. So, present predictions, let us conclude that the present developed model accurately determines HCPV cells performance over the temperature range studied.
The recommended PV system does not provide power to utility grid but it is expected to generate the load requirements. So, the energy produced is lost when the output of HCPV is larger than the load demand. The HCPV output and the load demand should be equal at each run hour. To confirm that concept, the simulated HCPV energy is correlated with hourly load data. The HCPV factors were changed till achieving the equality among HCPV output and corresponding hourly and annual energy.
An illustration for the output of this process is presented in Figure 6 for the day of maximum load (30 th August, 2015) for HCPV of 1000 MW. As the figure Figure 5. Variation of efficiency versus concentration factor for Azurspace cell.  shows, for 1000 MW HCPV output shaves the peak load by about 32%. Consequently this obviously illustrates the excellent match among the HCPV output and the hourly electrical load. This figure indicates that the HCPV system produces energy at peak load, i.e. the HCPV can definitely decrease peak load all over day while HCPV power not ever surpass the load.
Maximum monthly electrical energy load for the year 2015 is shown in Figure   7 for capacities of 0 MW, 1000 MW, and 2000 MW respectively. As figure illustrates, increasing HCPV system size results in significant decrease in peak load.
Also, peak load during the whole year, can be reduced by utilizing HCPV system with capacity of 1000 MW.
Calculation of the individual impact on load reduction is an alternative strategy to examine the capability of the HCPV system. That can be carried out by assessing total decrease in load demand by including all effects. Load requirements reduction is defined as monthly average load reduction at all day times during complete months. Figure 8 presents the change of the ratio of monthly average load reduction against HCPV size.
The ratio of average monthly demand reduction is defined as the average monthly demand reduction in MW for each 1 MW PV output. The relationship among HCPV size and average monthly load reduction is straight till HCPV size of 1000 MW. So, this ratio is constant and equal to about 0.69 till 1000 MWs.
Increasing HCPV capacity above 1000 MW results in a decrease in this ratio.
The reduction is mainly attributed to energy loss as HCPV energy starts to be   The generated power from HCPV is proposed to supply domestic hot water load and electricity consumption for citizens in an ordinary Kuwaiti house. The hot water demand is 280 liter/day presuming a 40 liters/person/day. The computer model is supplied with the ordinary loads consumption. The two-story house comprised 2 living rooms, dining room, 5 bedroom, 2 kitchen as well as a set of household apparatus. An hourly load pattern is provided to subroutine to be utilized during simulation. The model program is also supplied with the hours in which the load is employed throughout the whole for household appliances.
Various HCPV array azimuth angle and slopes are examined to achieve maximum annual HCPV energy generation. The maximum energy generation from the HCPV system occurs at array inclination of 25˚ (Kuwait latitude-5˚) and due south. Peak energy generation at angles lower than region altitude agree well with the weather condition in Kuwait since much radiation is available in summer more in winter.
Emission produced in manufacture process of PV system parts should be considered to get precise results. However, the CO 2 emission rate from PV is generally greatly smaller than the CO 2 emission rate from fuel sources, so it is ignored in the present work. The change of CO 2 emission avoided annually with tilt angle is shown in Figure 9.
As seen from Figure 9, once again the optimum tilt angle corresponding to maximum avoided CO 2 emission is 25˚. The avoided CO 2 emission at this optimum angle approximately equals to 1.55 ton/year clearly proofing the important effects of grid connected HCPV on environment in Kuwait weather conditions.

Avoided Co 2 emission (tonne/year) Smart Grid and Renewable Energy
Furthermore applying Kyoto Protocol that enforce penalties on greenhouse gases emissions will increase the price of conventional energy resources making HCPV more feasible. Though, this protocol is not activated currently in Kuwait, but its activation will endorse the economical and environmental impacts of PV systems much more. Finally, it is worth to point out that economic analysis of HCPV grid connected system is not taken into account in this study. However, it is necessary to continue this research by investigating the feasibility of HCPV systems. These results can assist Kuwaiti government in considering the application of renewable energy resources in Kuwait.

Conclusions
The present study has assessed the ability of HCPV to minimize peak load in addition to the environmental analysis of these systems in Kuwait weather conditions. The following conclusions can be stated out depending on the present outcomes: • Single diode model is satisfactory for practical applications rather than using the complex two-diode model. The total root mean square errors in the present model predictions are lower than 2% compared with published experimental data. • The electrical efficiency (η) of HCPV module is noticed to increase with concentration to a certain concentration level after which it decreases.
• Employing grid connected HCPV system significantly decreases the peak load.
• The peak load can be reduced by about 32% by using 1000 MW HCPV capacity.
• For HCPV capacity up to 1000 MW, the average peak demand is reduced to 0.69 MW for each 1 MW HCPV capacity.
• Energy generated from grid connected HCPV system is maximum for arrays due south and with inclination to the horizontal of 25˚ (Kuwait latitude-5˚).
• The avoided CO 2 emission is approximately 1.55 ton/year at the optimum conditions. • The present work clearly proves the environmental effects of the HCPV system in Kuwait climate.