High Power Interleaved Boost Converter for Photovoltaic Applications

Interfacing DC sources to load/power grid requires DC converters that produce minimum level of current ripples. This is to limit the losses and hence increase the life span of these sources. This article proposes a simple interleaved boost converter that interfaces PhotoVoltaic (PV) module into a common DC-link. The article also addresses the faulty mode operation of the proposed circuit while advising the appropriate remedy actions. A MATLAB and Simulink dynamic platform are used to simulate the transient performance of the proposed converter. The results revealed the effectiveness and the viability of the proposed converter in reducing the ripples in the PV current without employing bulky input inductors or increasing the switching frequency.


Introduction
PV industry gains more intention recently, due to the salient advantages of PV modules as size variability, environmental compatibility and modularity.PV in general requires mechanical and electronic tracking for producing maximum output power at different levels of solar irradiance and temperature.Mechanical tracking could be efficient large-scale PV circuits as in utility scale PV installations.However, in residential and small-scale PV arrangements, usually mechanical tracking is ignored.This is to optimize the complexity and implementation costs.However, electronic tracking is mandatory for all scales of PV instal- lations [1].
Tracking of Maximum Power Point (MPP) usually is realized via a DC-DC converter; the control methodology is to increment/decrement PV voltage/current such that MPP is realized.In other approaches, PV voltage/current is forced to follow a predetermined reference.This reference is extracted from actual PV voltage and current [1] [2].
Basic DC-DC boost converter is the preferred for PV applications.This is due to topology of this converter.The inductor in the input side reduces the ripple in the current drawn from PV and hence its losses.Moreover, the diode in the basic cell protects the PV module from reverse current.However, for reduced ripple level in the PV current, a volumetric inductor has to be used [2] [3] [4].This inductor impacts the weight and efficiency.Alternative solution is the application of interleaved boost converter.
Interleaved boost DC-DC converter consists of two cells of basic converter operating parallel.It is able to reduce the ripples in PV current without requirements of sizable inductor or high switching frequency.This is accomplished via introducing phase shift between the switching signals of the switches in the parallel cells.Moreover, the interleaved boost converter reduces efficiently the Electromagnetic Interference (EMI).The application of non-isolated interleaved boost converter was investigated in the literature for PV field [5] [6] [7] [8].In general, a little is reported regarding the limitations of the interleaved boost converter.
The limitations of the interleaved boost converter are highlighted in this research, while conditions for ripple-free input current operation are identified [5] [6] [7] [8].The reliability of power electronic components decreases with aging; therefore, there is considerable probability of faulty operation of interleaved boost converter.Less is reported in the literature about faulty mode of interleaved boost converter in PV applications.This results in decreasing the harvest power under such conditions as there is no comprehensive analysis or valuable remedy strategy [14].
Elaborate remedy strategies are advised for different faults in the operation of interleaved boost converter driving PV module, which are not widely reported [14].This confirms the originality of this article.
This article analyzes comprehensively the operation of interleaved DC-DC boost converter for PV applications.The limitations on the output voltage of the converter are derived.An annotative implementation scheme for the modulation strategy ensuring equal value of switches' duty cycles is proposed.The article directs more emphasis on the faulty mode of the proposed converter operation.Different fault scenarios are investigated while advising the appropriate remedy strategy.This article has the following contributions: 1) Defining the upper limit of the duty cycle and hence output voltage for interleaved boost converter.
2) Proposing a simple modulation strategy ensuring equal values for the switches' duty cycles.
3) Investigating the operation of interleaved boost converter while a switch develops short/open circuit fault and advising the appropriate remedy scheme.

4) Proposing intelligent remedy scenario while the interleaved boost converter
operating with open diode fault.

Interleaved Boost Converter and PV Module
The system under concern is composed of PV generator, interleaved boost converter and DC-link, as shown in Figure 1.The input DC capacitor is embedded to protect the PV generator and limit the losses, which results in increases lifespan of the PV module.The interleaved boost converter is chosen to interface PV module into common DC bus due to: 1) Interleaved boost converter has lower ripple level in the PV output current than the basic boost cell, which reduces the losses in the PV module and hence lengths its lifespan.
2) The interleaved boost converter has inherent short-circuit protection.
3) The interleaved boost converter has the same output voltage boosting ability as the basic cell.

PV Generator Model
Different models are advised for stimulating PV cell, these models differ in accuracy and complexity.Moderate model is advised here, the PV cell is modeled Figure 1.System under concern.
C in Journal of Power and Energy Engineering as a solar irradiation and temperature dependent current source I ph in parallel with diode as shown in Figure 2.This combination is in series with a series resistance Rs [14].This model of the PV has the advantages of accuracy, robustness and simplicity.
Basically, the PV cells are grouped in series to deliver a reasonable voltage/power, these structures as mentioned before are themed modules.The module has an equivalent circuit similar to that of the cell.
The relation between the terminal current I and voltage V of a PV module is expressed by [14], e 1 where I o , I ph , I and V are saturation current, photo current, current and voltage of the module.V th = nN s kT/q is thermal voltage of the module; n, N s , K, T and q are ideality factor, number of cells in series, Boltz's man constant and electron charge respectively.The PV modules under concern are from Kyocera KC200GT type.The parameters of KC200GT module are given in Table 1 [14] [15] [16].
The value of series resistance R s calculated by iterative method in [14] is 0.221 Ω.
The PV modules are grouped in series-parallel arrangement to form array, which is termed here as PV generator.Each PV generator is consisting of 30 Kyocera KC200GT modules.The relation between the PV array/generator terminal voltage V pv and current I pv could be expressed by a relation similarly to (1), however, it is more meaningful to express the PV array/generator current in  the module, as these data are commonly supplied by the manufacturers at standard test conditions [14].
where M ss and N ss are number of shunt and series connected modules respectively.The current I pv and the voltage V pv of the PV array/generator under concern calculated at 25˚C and different radiation levels are given in Figure 3 and Figure 4 respectively.Figure 3 and Figure 4 reveals that the voltage at maximum power is less dependent on the solar irradiation [14].Moreover, the generator current/power varies almost linearly with the insolation.Figure 5 shows the relation between the short-circuit current and current maximum power point for different levels of solar irradiance.
Figure 5 shows that current at maximum power point nearly varies linearly with the short-circuit current.For the PV module under concern [9] [10] [11] [12], the relation between I mpp and I sc could be given by, where K mppsc is equal to 0.9286, Figure 5.

Interleaved Boost Converter
The interleaved boost converter as shown in Figure 1 is composed from two parallel boost cells, which operate in an interleaved mode.Therefore, there is   given by, Assuming that L 1 and L 2 are equal, L 1 = L 2 = L.The ripples in the input current I L is given by, ( ) Equation (6) shows that zero ripple in the input current IL could be realized if D 1 = D 2 .However, this condition places a limit on the maximum value of the duty cycles D 1 and D 2 .As, the two cells operate in cascaded pattern; therefore, D 1 + D 2 = 1.0.Therefore, for zero ripple in the inductor current D 1 = D 2 = D, and the duty cycle of each boost cell is limited by, Equation (7) indicates that maximum value of a cell duty cycle is 0.5; this set the maximum output voltage of interleaved boost converter to twice input voltage.This considers a major deficiency in the interleaved boost converter.There is no limitation on the output voltage of basic boost converter as compared to the interleaved boost chopper.

Proposed MPPT
The slope of power-voltage curve of a PV generator, Figure 4, could be ex- where I PV , V PV and P PV are PV module current, voltage and power respectively.
The slope of power-voltage curve of a PV module, Figure 4, is positive on the MPP is tracked by continuously comparing the incremental and instantaneous conductance and incrementing/decrementing the PV voltage/current until MPP is reached.This technique is reported in the literature under ICC [9].
An innovative implementation for ICC is proposed here under the theme of Modified Incremental Conduction Controller (MICC).According to (9), the sum of the incremental and instantaneous conductance is equal to zero at MPP; therefore, employing a sufficiently fast PI controller ensures that sum is settled at zero.
This article proposes an innovative approach to ensure equal duty cycle for the switches of the converter.This is the condition for zero ripple, which is extracted from (6).Sawtooth of a switch is inversion for the other switch as shown in Figure 7.Moreover, the PI output DC signal is limited to half of Sawtooth amplitude.This is to comply with (7).The proposed modulation strategy ensures equal value for the switches' duty cycles and not violating the 50% upper limit of the duty cycle.The parameters of interleaved boost converter are given in Table 2.

Controller Tuning
To tune the proposed PI controller, the large signal model of the system under    [16].The following assumption are considered: 1) The input/output capacitors C in and C o are sufficiently large, so that the PV module output voltage V pv and output voltage V o are constant.
2) The converter input current is ripple free.
The dynamic performance model of the interleaved boost converter is similar to the basic boost topology.Averaging over a switching cycle, the dynamic performance of the interleaved boost chopper could be depicted by [17] [18], ( ) ( ) where i L , V o , R L and C o are respectively inductor current, output voltage, load resistance and output capacitance respectively.D is the duty cycle.
( ) ( )( ) ( ) where D o , I Lav and V os are steady-state values of duty cycle, average inductor current and output voltage.Rearranging ( 13) and ( 14), solving for V o (s); then substituting V o (s) in terms of I L (s) and D(s), the transfer function between inductor input current and duty cycle is given by, A PI controller with parameters given in Table 3 is used to force the operating point to track MPP irrespective to solar irradiance and temperature levels.The

Results and Discussions
MATLAB and its dynamic platform, Simulink, are used to stimulate the system under concern with the proposed control methods and MPPT technique.A solar irradiance that varies according to daytime is considered for validating the system under concern.This pattern of solar irradiance is shown in Figure 9.The PV output power, voltage and current are illustrated.The currents and the ripples in the inductors of the two cells also are given in Figures 9-11.
The ICC successfully forces the PV generator to operate at MPP at different solar irradiance, Figure 9. Figure 9 shows clearly the linear dependency between the solar irradiance and PV output power.
Figure 10 shows that PV terminal voltage is slightly solar irradiance dependent.The DC-link output voltage is not constant as the interleaved boost converter is controlled such that MPP is tracked at different solar irradiance irrespective to the output voltage.
Figure 12 shows that the PV input current is linearly proportionated with solar irradiance, Figure 9.The oscillations in the currents of the inductors may be due the interaction between the inductors and input/output capacitances.It is clear that the proposed cancellation technique is working as shown in bottom graph of Figure 11.

Remedy Strategy
Faulty mode of the interleaved boost under concern considers only the defects in Journal of Power and Energy Engineering  2) Scenario#2 a switch short-circuit fault.
Appropriate remedy strategies are identified for each scenario.

Scenario#1 a Switch Open-Circuit Fault
If a switch in a boost cell develops open-circuit fault, the current in this switch diminishes to zero.Moreover, the diode of this cell would be reveresbias, therefore the current in the inductor of the faulty cell drops to zero.However, as the interleaved boost converter consists of two cells.The other cell still operates and fulfills the load.This scenario is illustrated in Figure 12 and Figure 13, where the PV module input current, inductors' currents, PV output power and voltage are drawn.Here in this scenario, the solar irradiance is assumed constant at 1000 W/m 2 during the simulation time span.
Figure 12 shows that prior the fault the system was operating at MPP.Then, the system operation is diverted from MPP after the fault.Moreover, the ripple cancellation technique efficiently reduces ripple level in the PV input current.
Figure 13 shows that the system only experience around 4% drop in the output power.The increase in the PV output voltage is due to diversion from MPP operation (Figure 13).

Scenario#2 a Switch Short-Circuit Fault
Short-circuit switch fault is the severest, as the PV generated would operate at short-circuit operating point, where the output power is zero and the current is maximum.This scenario is illustrated in Figure 14, where the PV input current and DC-link voltage are drawn.Again, the solar irradiance is assumed constant at 1000 W/m 2 over the simulation time span.
Figure 14 shows that the input current after the fault suddenly jumps to the short-circuit current level.This ultimately increases the losses within the PV   generator.The DC-link voltage decreases to zero after the fault.The effect of the energy stored in the output capacitor is clear in Figure 14.
The proposed remedy is interfaced the interleaved boost converter to the PV generator via a switch.This switch would be continuously on during normal operation.However, it disconnects the circuit if the PV input current equals to the short-circuit current value.

Scenario#3 a Diode Open-Circuit Fault
This scenario investigates the open-circuit diode fault that develops in a converter cell.This scenario is illustrated in Figure 15 and Figure 16 where the PV module input current, inductors' currents, PV output power and voltage are drawn.Again, in this scenario, the solar irradiance is assumed constant at 1000 W/m 2 over the simulation time span.Figure 16 shows that fault scenario results in around 20% drop in the output power of the PV generator.The PV generator terminal voltage increases after the fault.This is due to departure of the operating point from MPP.The proposed control method of the interleaved boost converter enjoys the simplicity and flexibility [5] [6] [7] [8].This method is not complicated as the reported control methods [5] [6] [7] [8].Moreover, it allows almost instantaneous tracking for solar irradiance.

Conclusions
In general, the following conclusions could be extracted: 1) The interleaved boost converter has a maximum limit on the output vol-

Figure 3 .
Figure 3. Current a PV generator versus terminal voltage for 25˚C temperature and different levels of solar irradiance, locus of maximum power (black).

Figure 4 .
Figure 4. Power of a PV generator versus terminal voltage for 25˚C temperature and different levels of solar irradiance, locus of maximum power (black).

Figure 5 .
Figure 5. Short-circuit Current versus current at maximum power point for different solar insolation levels.
Journal of Power and Energy Engineering left of MPP, negative on the right and zero at MPP.Thus, the relation between the incremental and instantaneous conductance is given by,

Figure 8 . 5 Integral gain k i 20 Figure 8 .
Figure 8.The open loop transfer function has two complex poles and one right hand zero.Therefore, the PI controller has to ensure the stability while achieving reasonable bandwidth.The proposed PI controller, Table3, produces around 2.5 ×

Figure 9 .
Figure 9. Solar irradiance over a daytime(top) and PV output power (bottom) for 25˚C.

Figure 10 .
Figure 10.PV generator terminal voltage (top) and DC-link voltage (bottom) for varying solar irradiance and 25˚C.

Figure 11 .
Figure 11.PV generator input current (top), inductors' currents (middle) and ripples in the currents (bottom) for varying solar irradiance and 25˚C.

Figure 13 .
Figure 13.PV output power (Top graph), PV terminal voltage (bottom graph) for open-circuit switch fault at 100 msec.

Figure 14 .
Figure 14.PV input current (Top graph), DC-link voltage (bottom graph) for short-circuit switch fault at 100 msec.

Figure 15
Figure 15 shows the input current of PV generator and the currents in the inductors of the interleaved cells.It is clear that the proposed modulation strategy reduces the ripple, Figure 15.The current in the inductor of the faulty cell becomes discontinuous, while the other cell carries the full load current.The proposed remedy strategy is permantely to open the switch of the defected cell.This could be accomplished via continuous sensing of the inductors' currents.

60
Efficient interleaved boost converter is proposed to interface a PV module into common DC-link.The article also identifies the condition for zero ripple in the interleaved boost converter input current.The limitations of the interleaved boost chopper are highlighted.An innovative implementation of the control circuit of interleaved boost converter is advised such that the two switches have Journal of Power and Energy Engineering
t V Journal of Power and Energy Engineering terms of the voltage V pv , short-circuit current I sc and open-circuit voltage V oc of

Table 2 .
Parameters of interleaved boost converter.