CFOA Based Band Pass and Band Stop Ladder Filter—A New Configuration

A new technique for the conversion of ladder based filter into CFOA based filter has been proposed. The technique uses signal flow graph and converts the existing LC ladder based filter into band pass & band stop configurations. The design of band pass and band stop filter has been realized using the proposed technique. The proposed configuration is implemented using CFOA as an active device and all the capacitors are grounded. CFOA based circuits have greater linearity, high dynamic rate, high slew rate and high signal bandwidth. Simulation has been carried out using simulation software P Spice (v10.1). The simulation results have been demonstrated and discussed.


Introduction
The birth of electronics lead to the need of new active devices and invention of transistors was extremely beneficial. After that VFA's or Voltage Feedback Operational Amplifiers were developed. However their dynamic performances were limited because of the gain bandwidth product and slew rate. Hence nowadays there is an inclination towards current mode circuits. The advantages of current mode circuits over voltage mode circuits are higher signal bandwidth, larger dynamic range, low-voltage operation, greater linearity, lower power consumption, simpler circuitry and simple implementation of signal operations, such as addition and subtraction [1]- [3].
Generally, element simulation & functional relation simulation are the two approaches which are used for ladder simulation. However, the former approach requires too many components. Most of the synthesis methods using OTA's for simulating higher order LC ladder filter involve either the complicated design procedure or a large number of OTA's. This paper presents a systematic approach using signal flow graph technique for realizing the passive ladder based band pass and band reject filter into CFOA based band pass and band reject filter. The resulting filters requires CFOA, resistors and capacitors and most of the capacitors are grounded. Furthermore, for thin film fabrication the use of grounded capacitors eliminates the etching process and reduces the number of gold contacts. Hence leading to a greater circuit reliability.
Current feedback operational amplifier (CFOA) based CM circuits have received considerable attention in many filtering and signal processing applications. Symbol diagram of the CFOA is shown in Figure 1. With the help of CFOA we can achieve the same characteristics of ladder based filter as they were in the original circuit and excluding the inductors [4]- [6]. Moreover, CFOA provides faster response and can operate at high frequency at high gain.
Although there has been a lot of activity on Universal Voltage Mode & Current Mode biquad filters realisation using CFOA's, comparatively only a few researchers have explored the methods of designing higher order filters using CFOA's. Previously, Rathore and Khot [7] have designed a Low Pass and High Pass filter configuration using CFOA. They have given a systematic method of deriving CFOA based all grounded capacitor filter from Current Mode RLC prototype ladders. Sinhaetl proposed a Signal Flow Graph approach for realizing CFOA based high pass and low pass ladder filter [8]. Referring to the Low Pass and High Pass configurations presented in research paper [7] [8], we have prepared two different combinations of Band Pass and Band Reject Filter.
In this paper, active realization of Band Pass and Band Reject ladder filter using current feedback operational amplifier (CFOA) has been presented. We have considered two cases in both band pass and band reject filters and obtained the result of both the cases.
The paper is organised as follows: 1) Introduction.

Transformation of Ladder Band Pass Filter into CFOA Based Band Pass Filter
Improvements have been done in the passive ladder based Band pass filter by converting it into CFOA based band pass filter. This has been done by removing inductor from the ladder based filter which makes it better. The conversion of ladder based filter into CFOA based filter is as follows: Two structures of Ladder Based Band Pass filter has been considered and analysis has been done. These structures have been presented in 2 cases as follows:

Conversion into Voltage Form
These equations are converted into voltage form to remove current element and hence we get the following equations:

Signal Flow Graph
With the help of these equations we make a signal flow graph which has been shown in Figure 3.

CFOA Filter
Using the signal flow graph, CFOA based band pass filter for case 1 has been made as shown in Figure 4.

Observations
The passive and CFOA based ladder band pass filter circuits shown in Figure 2 and   Inductors are used for the passive ladder based circuit. Now the circuit is simulated in PSPICE CAPTURE and its AC analysis is done.

Response of CFOA Based Band Pass Filter
CFOA band pass filter uses the AD844 IC and a power supply to drive it. The circuit is simulated in PSPICE CAPTURE and its AC analysis is done. The graphical output obtained is given below in Figure 5.

Case 2
Second model of band pass filter (Figure 6) which was also simulated and the results (Figure 8) are as follows:

Conversion into Voltage Form
These equations are converted into voltage form to remove current element and hence we get the following equations:

Signal Flow Graph
With the help of these equations we make a signal flow graph of the passive ladder based structure of band pass filter (case 2) which has been shown in Figure 7.
The passive and CFOA based ladder band pass filter circuits shown in Figure 6 and Figure 8 are designed and evaluated in PSPICE CAPTURE using conventional resistors, capacitors and AD844 IC as CFOA.

Response of CFOA Based Band Pass Filter (Case 2)
For CFOA we use the AD844 IC and a power supply is attached to drive it. The circuit is simulated and its AC analysis is done. The graphical result obtained is shown in Figure 9.

Transformation of Ladder Based Band Stop Filter into CFOA Based Band Stop Filter
In signal processing, a band-stop filter or band-rejection filter is a filter that passes most frequencies unaltered, but attenuates those in a specific range to very low levels. It is the opposite of a band-pass filter. Like band pass filters, band-reject networks can also be derived from a normalized low-pass filter by a suitable transformation. Wideband band-reject filters can also be obtained by combining low-pass and high-pass filters. Both the input and output terminals are paralleled, and each filter must have a high input and output impedance in the band of the other filter to prevent interaction. Therefore, the order n must be odd and the first and last branches should consist of series elements. These restrictions make the design of band-reject filters by combining low-pass and high-pass filters undesirable. The impedance interaction between filters is a serious problem unless the separation between cut-offs is many octaves, so the design of band-reject filters is best approached by using a signal flow graph technique to obtain CFOA based bandreject filter from passive ladder based bandreject filter.
Two structures of Ladder Based Band Reject filter has been considered and analysis has been done. These structures have been presented in the two cases as follows:

RLC Based Band Stop Filter
The RLC based band stop filter has been shown in Figure 10.

Mathematical Analysis
After applying KVL and KCL in Figure 10, the following equations have been obtained:

Signal Flow Graph
The Signal Flow Graph of band reject filter has been shown in Figure 11.

CFOA Based Active Ladder Filter
The circuit diagram for CFOA based band stop filter has been shown in Figure 12.
The Signal Flow Graph was analysed and the blocks were converted to CFOA diagram. The passive and CFOA based ladder band reject filter circuits shown in Figure 10 and Figure 12 are designed and evaluated using conventional resistors, inductors, capacitors and AD844 IC as CFOA.

Frequency Response (Gain vs Frequency Response)
The circuit is simulated and its AC analysis is done. The graphical result obtained is shown in Figure 13.

Case 2
Second model of ladder based Band Reject Filter has been considered and following results were obtained.

Circuit Diagram of Band Reject Filter
The circuit diagram of ladder based band reject filter has been shown in Figure 14.

Mathematical Analysis
After applying KVL and KCL in Figure 14, the following equations have been obtained:

Signal Flow Graph
The Signal Flow Graph of band reject filter has been shown in Figure 15.

Conversion of Ladder Based Band Reject Filter into CFOA
The CFOA obtained after transforming passive ladder based bandreject filter into CFOA based bandreject filter has been shown below in Figure 16.

Frequency Response (Response for Case 2)
For CFOA we use the AD844 IC and a power supply is attached to drive it. The circuit is simulated and its AC analysis done. The graphical result obtained is shown in Figure 17.

Simulation Results
Simulation results of both the cases of Band Pass & Band Reject Filter are as follows:

Band Pass Filter
In Case 1, A Band Pass Filter is simulated with 1

Band Stop Filter
In

Conclusions
A systematic method using signal flow graph technique has been developed for converting passive ladder band pass and band reject filter into CFOA based band pass and band reject ladder filter. Such realisations are suitable for fabrication in integrated circuit technology. The CFOA based filters works satisfactorily at higher frequencies.
In the proposed configuration, we have used CFOA and resistors and capacitors for realising band pass and band reject filter. Most of the Capacitors which have been used in our configuration are grounded in nature. The grounded devices are easy to fabricate in VLSI chip. The filter configuration designed in the proposed configuration has replaced the inductor completely which reduce the size of the circuit and hence, make it less bulky and expensive which is a major requirement of VLSI design.
The summary of the components used, the various frequencies and the bandwidth of band pass and band reject filter used in our configuration has been illustrated in Table 1.
These filters imply a minimum No. of capacitors, resistance and CFOA. Such filters are suitable for fabrica-