Performance Improvement of CIGS Solar Cell: A Simulation Approach by SCAPS-1D

Thin-film solar cells possess the distinct advantage of being cost-effective and relatively simple to manufacture. Nevertheless, it is of utmost importance to enhance their overall performance. In this research work, copper indium gallium selenide (CIGS)-based ultra-thin solar cell (SC) configuration (Ag/ZnO/ZnSe/CIGS/Si/Ni) has been designed and examined using SCAPS-1D. The numerical calculations revealed that this new design resulted in a substantial improvement in SC performance. This study explores the utilization of two absorber layers, CIGS and Si, both with a total of 2 μm thickness, to enhance device performance while reducing material costs, observing an increase in key SC parameters as the Si absorber layer thickness is increased, reaching a maximum efficiency of 29.13% when CIGS and Si thicknesses are set at 0.4 μm and 1.6 μm, respectively with doping absorber doping density of 10 14 cm −3 . Furthermore, we analyze the impact of variation in absorber and buffer layer thickness, as well as doping concentration, surface recombination velocity (SRV), electron affinity, series-shunt resistance, and temperature, on optimized CIGS SC parameters such as short-circuit current density (J SC ), open circuit voltage (V OC ), fill factor (FF), and power conversion efficiency (PCE). The findings yielded by the investigation offer significant elucidation regarding the fabrication of economically viable and highly efficient non-hazardous CIGS


Introduction
Renewable energy sources such as solar energy have the potential to serve as via- ble alternatives to non-renewable sources, such as fossil fuels.Solar energy, being an in-exhaustible and sustainable energy source, exhibits remarkable potential for meeting energy needs [1].Notably, solar power generation is not only environmentally friendly, but also free from any adverse consequences such as pollution or noise.Solar cells (SCs) are ingeniously designed to harness the abundant solar energy emitted by the sun and effectively transform it into a readily available form of electrical power.Moreover, SC fabrication has improved greatly over time.
However, the cost-effectiveness and overall efficiency of SCs continue to pose significant hurdles in their advancement [2] [3] [4].Therefore, the primary objective of technological progress in the photovoltaic (PV) sector is to develop high-efficiency SCs while simultaneously minimizing production costs [5] [6] [7].Hence, throughout the past few decades, extensive research has been conducted by researchers on materials that meet the requirements of affordability, effectiveness, and longevity in the PV field [8] [9].Copper indium gallium selenide (CIGS), belonging to the group I-III-VI, has emerged as a highly promising choice for thin-film SCs (TFSCs).This is primarily owing to its excellent conversion efficiency, which has recently surpassed 23% [10] [11] [12].Additionally, CIGS exhibits remarkable stability, cost-effectiveness, and configurable band gap of roughly 1.01 -1.69 eV [13] [14].This puts them in close competition with silicon PV cells, which currently have a PCE of 26.7% [15] and other competing materials such as a-Si, CdTe [16] and CZTS [17].Moreover, it has an excellent absorption coefficient in the visual spectrum of approximately 10 5 cm −1 , making it more desirable and effective for solar applications [6] [10].However, the challenge lies in the fact that the combination of Ga (Gallium) and In (Indium) materials in the CIGS sample is both scarce and expensive.As a result, researchers are directing their attention towards reducing the thickness of the absorber layer to minimize the usage of Gallium and indium in an effort to decrease the overall production expenses.But, the electrical properties of CIGS TFSCs are influenced by the thickness of the active layer, and a reduction in thickness can potentially lower SC performance.The ideal thickness of the active layer, according to some researchers, is between 2 and 3 µm [18] [19].On the other hand, recent studies have produced CIGS-based cells having active layer thicknesses of under 1 µm that are quite effective [20]- [24].In a study conducted by Movla et al. [20], it was shown that an absorber layer made of graded CIGS material with a thickness of 0.5 µm, combined with a transparent conductive oxide (TCO) layer of thickness 20 nm, results in an impressive efficiency of 20.34%.Similarly, Vermang et al.
carried out a study where they achieved an efficiency of up to 13.5% using ultra-thin CIGS solar cells [21].These cells had a CIGS absorber layer with a thickness of 0.385 µm.The experimental PV solar cell efficiencies were investigated by Garris et al. [22] over a range of thicknesses.They discovered a remarkable efficiency of 15.15% in a CIGS layer with a thickness of 0.490 µm.In a separate investigation carried out by Chadel et al. [23], an impressive conversion efficiency of 24.43% was attained by utilizing a 0.2 µm CIGS absorber layer in con-junction with a 1 µm Si BSF layer.The results of earlier studies offer useful information for optimizing ultra-thin CIGS solar cells, resulting in increased efficiency and stability with reduced cost.Therefore, in order to develop a low-cost CIGS solar cell with enhanced efficiency, we introduced a dual absorber layer-based SC.
In this paper, an alternative configuration of CIGS-based ultra-thin SC has been proposed.The numerical analysis of the performance of a newly proposed Ag/ZnO/ZnSe/CIGS/Si/Ni SC is conducted using the SCAPS-1D simulator.
SCAPS-1D has gained extensive popularity for numerical simulations of SC due to its open-source characteristics, adaptability, ease of use, and precision.Here, we employed a dual absorber configuration consisting of two distinct layers, namely CIGS and Si.A SC with two absorber layers is more effective because it can absorb solar photons throughout a wider spectral range [25].To get maximum performance at the lowest cost, we put a specific emphasis on optimizing the thickness of the absorber layer.Moreover, cadmium sulphide (CdS) is commonly employed as a buffer layer in CIGS SCs.The toxicity of cadmium is the most significant disadvantage of CdS.Hence, in order to develop an environmentally friendly and non-toxic CIGS SC, CdS buffer layer is substituted with a ZnSe layer, and the optimization process is subsequently pursued.Furthermore, we investigate the impact of incorporating a Si absorber layer on the performance of the device.
In addition, we explore the effects of changes in the thickness of the absorber and buffer layers, as well as variations in doping concentration, surface recombination velocity (SRV), electron affinity, series-shunt resistance and temperature, on the optimized CIGS SC parameters.

Device Configuration and Material Parameters
The ZnSe serves as the buffer layer due to its non-toxicity, high optical transmittance, and wide bandgap, which together contribute to a substantial optical throughput in the hetero-junction structure.The suitable electron affinity of the ZnSe buffer   Hole SRV (cms −1 ) 10 7 10 5 Work Function (eV) 5.25 4.26

Impact of Absorber Layer Thickness
The thickness of the absorber layer plays a pivotal role in the development of SC.This is due to the fact that a thicker absorber layer can lead to an increase in carrier recombination, while a thinner absorber layer may result in insufficient light ab-sorption [25].Consequently, the current density and efficiency of the SC experience a decrease.Therefore, it is essential to meticulously choose the appropriate thickness in order to enhance the performance of the SC.
As can be seen in Figure 2, the V OC , J SC , FF, and PCE are all influenced by the absorber layer thickness.When the CIGS/Si is thickened, more pairs of electrons

Doping Concentration Optimization of CIGS and Si Layer
The influence of doping concentration on the performance of SCs was studied by examining the impact of changing the doping concentration from 10 12 to 10 20 cm −3 in the CIGS and Si absorber layers, while maintaining the respective layer thicknesses at 0.4 and 1.6 μm, as depicted in Figure 3 closer to the energy level of the bandgap.As a result, the built-in potential rises, raising the V OC [30].The value of Jsc decreases with the increase in doping concentration of the both absorber layer.This is due to the increase in carrier recombination at higher doping densities [31].The FF and PCE also show the similar down trend beyond doping concentration 10 16 cm −3 for both absorber layers.The findings demonstrate that the optimal performance of the newly developed dual absorber CIGS-based SC has obtained with the doping concentration of 10 14 cm −3 which yield overall PCE of 29.13%.

Effect of Thickness and Doping Concentration of ZnSe Buffer Layer on SC Parameters
The thickness and doping concentration of the ZnSe buffer layer have been optimized by varying them from 0.02 µm to 0.4 µm and 10 12 to 10 20 cm −3 correspondingly.The result is illustrated in Figure 4. Figure 4 depicts the SCs influence on Voc, with the values rising slightly in accordance with the thickness of the ZnSe buffer layer.Additionally, it has been shown that the Jsc values of the SC decrease as the thickness of the ZnSe buffer layer increases.This is due to the fact that a larger buffer layer leads to more photon losses [32].Consequently, it would result in a reduction in the number of photons that passed through the absorber layer.When the ZnSe buffer layer is thicker, the FF and PCE also begin to decline.Jsc, FF, and PCE, which are at their greatest levels at lower doping concentrations except Voc.Voc is not significantly affected by variations in the doping concentration of the ZnSe buffer layer.However, increased buffer layer doping concentration creates a powerful electric field that efficiently attracts electrons and opposes minority carriers away from the interface between the buffer layer and absorber layer, reducing interface recombination [32].We choose the thickness 0.025 µm and doping concentration 10

Impact of Series and Shunt Resistance on CIGS-Based Solar Cell
Figure 5 illustrates the assessment of PV characteristics by changing the series resistance from 1 to 5 ohm-cm 2 and the shunt resistance from 10 to 10 5 ohm-cm 2 .
A slight variation in Voc is observed due to changes in the series and shunt resistance, with Voc changing from 0.43 V to 0.78 V only when the shunt resistance ranges from 10 to 10 2 ohm-cm 2 , after which it remains relatively constant.
Moreover, Figure 5 indicates a significant variation in the value of Jsc, showing an increase when the series resistance is low and the shunt resistance is high, leading to a significant improvement in Jsc of 39.17 mA/cm 2 to 43.09 mA/cm 2 for shunt resistance values between 1 and 10 5 ohm-cm 2 and a decrease of 39.17 mA/cm 2 to 28.72 mA/cm 2 for series resistance values between 1 and 5 ohm-cm 2 .
It is noticed from Figure 5 that the impact of series resistance on FF and PCE is minimal, while shunt resistance shows a significant effect on FF and PCE, leading to an increase in both FF and PCE from 25.00% to 80.64% and 4.22% to 27.40%, respectively, as the shunt resistance value increases from 1 to 10 5 ohm-cm 2 .
Figure 5.The impact of series and shunt resistance on SC parameters.

Variation of Parameters Due to Electron Affinity
The influence of the electron affinity of the CIGS absorber layer on the properties of the SC is shown in Figure 6.When the electron affinity of absorber layer fluctuates between 4.1 and 4.6 eV, Voc and Jsc values raise.At the interface between the semiconductor material and the absorber layer, a stronger electron affinity encourages more effective charge separation, which increases the flow of electrons [10].The FF and PCE, however, decrease as the electron affinity value increases over 4.4 eV.This may be related to the SC's rising resistance.

Impact of Surface Recombination Velocity on SC Parameters
In thinner absorber layers, the proximity between the back contact and depletion region is significantly reduced, thereby enhancing the likelihood of carrier recombination in the back contact.This indicates the importance of investigating the impact of surface recombination velocity (SRV) on the performance of SC parameters.The impact of the SRV varying from 10 2 to 10  and is depicted in Figure 7.It is observed that Voc of 0.96 V at 10 2 cms −1 and deteriorates till 0.61 V with decreasing of SRV till 10 5 cms −1 .But the curve of Jsc is 43.09 mA/cm 2 , which is constant with respect to increasing SRV.FF is gradually decreased until it reaches 10 6 cms −1 , after that point it is abruptly decreased.The surface recombination velocity impacts the efficiency by decreasing a constant manner.Due to the rapid recombination of electrons and holes, a high SRV drastically reduces the minority carrier lifetime and diffusion length, thereby decreasing the SC performance parameters [33].A fixed value is always chosen for perfect SRV.At 10 5 cms −1 SRV, We get the value of Voc, Jsc, FF, and PCE are 0.78 V, 43.09 mA/cm 2 , 85.83%, and 29.12%, respectively.

Variation of CIGS Output Parameters Due to Temperature
The assessment of the Voc, Jsc, FF, and PCE has been carried out to evaluate the implications of the temperature change between 280 K and 380 K, as depicted in

Comparative Analysis
In this study, the advantage of incorporating absorber (Si) layer into CIGS-based TFSCs using ZnSe as a buffer layer has been investigated.A Si absorber layer of 1.6 µm and a buffer layer of 0.025 µm, in addition to the CIGS absorber layer, contribute to the overall 29.13% efficiency in this SC, which is higher than the reported CIGS SC in previous studies, listed in Table 4.The addition of this absorber layer greatly increases the performance of the SC.

Conclusion
CIGS-based SC configuration of Ag/ZnO/ZnSe/CIGS/Si/Ni was proposed and simulated using SCAPS-1D software, and numerical calculations revealed that this new design resulted in a substantial improvement in SC performance.This study explores the utilization of two absorber layers, CIGS and Si, both with a total of 2 µm thickness, to enhance device performance while reducing material costs, observing an increase in key SC parameters as the Si absorber layer thickness is increased, reaching a maximum efficiency of 29.13% when CIGS and Si thicknesses are set at 0.4 µm and 1.6 µm, respectively with doping absorber doping density of 10 14 cm −3 .The output parameters have been meticulously determined through a comprehensive analysis of the effect of buffer layer thickness variation and doping concentration variation, SRV, series-shunt resistance, and temperature.The incorporation of the silicon (Si) layer boosts the absorption of photons and decreases the recombination rate, thereby ultimately leading to enhanced output efficiency parameters.The aforementioned findings indicate that the recently developed SC configuration holds great promise for integration within the solar cell community, enabling the realization of highly efficient CIGS SCs while simultaneously reducing overall costs.
How to cite this paper: Wahid, M.F., Howlader, M.N., Ahasan, N. and Rahman, M.M. (2023) Performance Improvement of CIGS Solar Cell: A Simulation Approach by SCAPS-1D.Energy and Power Engineering, 15, 291-306.https://doi.org/10.4236/epe.2023.158015DOI: 10.4236/epe.2023.158015292 Energy and Power Engineering investigation of performance parameters for the newly designed Ag/ZnO/ ZnSe/CIGS/Si/Ni SC involved the use of one-dimensional electrical Solar Cell Capacitance Simulator structures (SCAPS-1D) software.This software developed by the Department of Electronics and Information Systems at the University of Ghent, Belgium, analyzed the electrostatic potential and behaviour of free carriers within the SC through the implementation of the continuity equations and Poisson equation, comprising up to seven semiconductor materials[26].The device configuration of the newly developed SC is shown in Figure1(a).The SC is made up of a p-CIGS and p-Si absorber layer, an n-ZnO window layer, and an n-ZnSe buffer layer.The additional p-Si absorber layer in the proposed design has a band gap of 1.12 eV.To facilitate efficient light absorption, minimize electrical losses, promote effective charge carrier transfer, and protect the underlying layers, we employ ZnO as window layer.ZnO is preferred due to its high transparency, low resistivity, favorable interface characteristics, and wide bandgap.
and holes are produced, which advances efficiency and causes a decrease in FF owing to resistance and an increase in J SC .The symbols (C1 to C11) are used to indicate the thickness combinations among the two absorber layers, which are demonstrated in Table3.It is observed from Figure2that maximum SC performance has been achieved with thickness combination C9, where CIGS of 0.4 µm and Si of 1.6 µm thicknesses were used.This demonstrated that an increase in the thickness of the Si layer leads to an increase in SC performance.

Figure 2 .
Figure 2. Impact of varied thicknesses of CIGS and Si absorber layers on Voc, Jsc, FF and PCE.
(a) and Figure 3(b).The SC output characteristics barely change when the CIGS absorber layer and Si layer's doping concentration changes 10 12 to 10 16 cm −3 .Beyond the doping concentration of 10 16 cm −3 of the CIGS absorber layer and Si layer, the value of V OC rises.Doping changes the Fermi level within the semiconductor, bringing it

Figure 3 .
Figure 3. Variation of performance parameters for doping concentration of CIGS and Si absorber layer.

Figure 4 .
Figure 4. Variation of performance parameters for thickness and doping concentration of ZnSe buffer layer.

Figure 6 .
Figure 6.The impact of varying electron affinity of CIGS on SC parameters.

Figure 8 .Figure 7 .
Figure 8.For the proposed CIGS-based hetero-structure, Voc, FF, and PCE values have changed from 0.81 V to 0.66 V, 86.81% to 81.01%, and 30.60% to 23.25%, respectively, between 280 K and 380 K.However, Jsc is 43.09 mA/cm 2 , which remains unchanged.It has been noticed that temperature change considerably deteriorates the values of Voc, FF, and PCE in the hetero-structures as a consequence of temperature-induced shrinking of the band gap[34].But nonetheless, Jsc in the hetero-structures remains stable, indicating that the creation of electron-hole pairs and the recombination are consistent throughout the entire

Figure 8 .Figure 9
Figure 8.The impact of temperature on SC parameters.

Table 1 .
Physical parameters of various layers from literature.

Table 3 .
Thickness combination of CIGS and Si in absorber layer.