Assessing Enabling Competence of Leagile Manufacturing Model and Its Impact on Performance of Small and Medium Factories in Uganda

Purpose: Leagile manufacturing is one of the time-based manufacturing practices used to improve factory performance. It is a practice that combines initiatives of Lean and agile manufacturing under certain enabling competences. Therefore, the purpose of this study is investigate the combinative nature of time-based manufacturing practices under unique enabling competences and their impact on performance of factories in Uganda. Methodology: Firstly, the underlying factor structure of competences and time-based manufacturing was examined was conducted using Principal Component Analysis (PCA). Enabling competences and time-base manufacturing practices were modelled and validated for each using confirmatory factor analysis, particularly composite reliability, average variance extracted and convergent validity. A fully fledged structural equation model was used to test the impact of leagile manufacturing on performance of factories. Findings: The study results revealed that time-based manufacturing of lean, and leagile are related but differ, in terms of their enabling competences and philosophical orientation. The findings also revealed that when small and medium factories in Uganda adopt leagile practice, they are likely not improve their performance. This is perhaps due to the fact that small and medium factories have inadequate resources. Practical Implications: The study findings shed more insights on the factors that enable adoption and implementation of time-based manufacturing practices. The extent to which these competences are orchestrated determines the benefits derived from the time-based manufacturing practices. In addition, small and medium enterprises should keenly make a choice on the appropriate practices that purposely reduce their lead time and cost of conversion. Originality: This study investigated the combinative naHow to cite this paper: Nagaaba, N. (2022) Assessing Enabling Competence of Leagile Manufacturing Model and Its Impact on Performance of Small and Medium Factories in Uganda. American Journal of Operations Research, 12, 127-155. https://doi.org/10.4236/ajor.2022.124008 Received: April 6, 2022 Accepted: June 5, 2022 Published: June 8, 2022 Copyright © 2022 by author(s) and Scientific Research Publishing Inc. This work is licensed under the Creative Commons Attribution International License (CC BY 4.0). http://creativecommons.org/licenses/by/4.0/


Introduction
In order to cope with the competitive storms in manufacturing business, manufacturers attempt to exhibit excellence in specific operations by exploiting available competences. Therefore, different firms choose different paths to address specific market needs. Similarly, the fact that capabilities required to respond and provide products to the market at low cost differ from company to company, incorporating customer orientation services into manufacturing remains key in keeping low costs [1]. In some instances, manufacturing companies have chosen time-based manufacturing practices of lean, agile or leagile manufacturing practices [1] [2]. Literature shows that use of these practices have been widely debated especially the contribution of lean and agile manufacturing towards achieving performance [3] [4] [5]. Other streams of research have underscored leagile practice as a tool that delivers the benefit of both lean production and agile manufacturing. Whereas lean production emphasizes reduction in wastage by streamlining production processes, agile manufacturing emphasizes flexibility and responsiveness in a turbulent market [6] [7] [8].
Although scholars delineate lean and agile manufacturing practices as two distinct practices with different underlying emphasis [9], their simultaneous adoption in the context of this study has not been sufficiently addressed empirically.
Furthermore, literature indicates that, when a firm pursues a leagile infrastructure, it is able to capitalize on the benefit of lean and agile manufacturing. That withstanding, manufacturers in developing countries tend to earmark key factors that enable them pursue time-based manufacturing practices. More so, in disruptive and customer-based business environment, sustainability and growth have become crucial. As a result, factories need to re-orient their resources to cultivate different competences and become sensitive to delay effects and serve customers at low cost. "Shorter delays lead to greater trades" [10].
Related studies indicate that some companies put their attention on implementation of individual time-based manufacturing practices, yet other streams of thought advocate for combination of two or more practices in the same corporation [11]. The question here is which particular competences enable mutual  [12], identifying the distinctive competence required for each time-based manufacturing practice is very important and thus the first objective of the study: Objective 1: Validating multidimensionality of 3 interrelated enabling competences of time-based manufacturing; core, operational and business transaction.
In addition, practitioners that compete in a single supply chain the application of lean and agility as inclusive concepts is unavoidable. Evidence derived from developed countries has shown greater and synergetic yield from a combined application of time-based manufacturing practices under ICT innovations [7] [9] [13] [14] [15]. The epistemological argument is that, even though leanness and agility can be caught in a trade-off conflict causing considerable overlap between their characteristics [16], certain unique competences are needed to rightfully fix the burden by dividing it amongst manufacturing components. The theoretical insights drawn from TRIZ-Theory of Solving Inventive Problems, provides ways to overcome psychological barriers and burden of generating solutions to problems associated trade-offs among innovative strategies [16]. Developed by Genrich [17], this theory emphasizes systematic analysis of a problem to be solved and provides a series of guidelines for alternative solutions. TRIZ identifies and predicts the root causes of undesired phenomenon in a manufacturing system and advocates for timely correction to prevent any harmful event. Even though critiques to this theory point to individualized judgment of ideality rendering it biased, its strong hand is devoted to identifying solutions to challenges attributed to practices with conflicting interests [16]. In this study, business transaction competences are identified and how such competences are orchestrated in a leagile system is explained [4] [18]. The theoretical connotations of Hua, Yang, Coulibaly, & Zhang [19] identify leagile distinct practices with particular competences without distortion of overall strategy of lean and agile practices. As recommended by Ketokivi & Schroeder [20], bundles of capabilities are used to better capture the width of multidimensional concepts. Therefore, testing whether lean, agile and leagile manufacturing practices are related but distinct in the context of Ugandan factories is the second objective of this study: Objective II: Validating time-based manufacturing practices of lean, agile and leagile as distinct and related practices in the context of Uganda.
In attempt to examine the rationale for the adoption of time-based manufacturing practices in Uganda, leanness and agility should not be confused. Rather, leanness forms the basis for agility and establishment of lean practices does not focus on meeting customer needs in the quickest possible way [4]. Other authors argue that the success of agile manufacturing is determined by adequate lean production strategies [9], regardless of the enabling factors. Nonetheless, Thaeir [13] also argues that lean and agile paradigms are distinct concepts that are not entirely compatible. Therefore, deployment of leagile principles would yield related results from lean and agile initiatives. While there could be different streams of research on the contribution of the hybrid of lean and agile practices, their pragmatic intersection in the context of Uganda has not been fully documented. In a bid to establish the comprehensive hybrid model, the current study also targets at achieving the following objective.
Objective III: Examining the relevance of combining Lean and Agile manufacturing practices in leagile manufacturing system.
Finally, researchers claim that leagile system encompasses both lean and agile practices, acting together in order to improve factory performance [3]. The claim is yet to remain a fallacy among small and medium factories (SMFs) in Uganda if not empirically proved. For instance, factories in Uganda suffocate from delayed production and high conversion costs for numerous reasons. For example, being a landlocked country, factories experiences delays transporting imported raw materials, yet they have to meet on-time demands from both local and international markets. World Bank [21] report indicates that Uganda lags behind its counter-parts in terms of production lead-time with 19.03 days compared to Tanzania (10.23 days), Kenya (8.88 days) and South Africa (5.53 days). I addition, Nagaaba [5] indicates that industrial competitiveness and labor productivity in manufacturing sector is low, slowed from about 7 percent in 1991-2002 to 3 percent in 2002-2015. This also intrigued the development of the framework to address the operational gaps in manufacturing industry in the current study. Probably, with new developments and innovation in manufacturing, a leagile based infrastructure would be solution to upscale performance. This study therefore also seeks to address the following objective: Objective IV: Examining the contribution of leagile manufacturing in improving performance of small and medium factories in Uganda.
Overall, in order to address the above four objectives, a leagile manufacturing framework was adopted, validated, and tested to ascertain its contribution in improving factory performance. The hypotheses depicting the conceptual relationships of the factors and their practical contribution towards factory performance are tested in subsequent sections. The factor relationships are hypothesized as follows.
H1: Enablers of time-based manufacturing are threefold-competences (i.e. core, operational and business transaction), distinct but interrelated in nature.
H2: Time-based manufacturing practices of lean, agile and leagile are conceptually distinct in context of Uganda.
H3: Combination of Lean and agile manufacturing practices contribute to the establishment of a leagile manufacturing system. H4: Leagile manufacturing improves of factory performance of small and medium factories in Uganda. factory can adopt either of the practices without compromising benefits derived from others. The third hypothesis suggests that successful adoption of leagile is preceded by establishment of lean and agile systems in a particular factory. If it is rejected, then factories can uniquely adopt leagile practices at any level of operation without considering lean and agile practices. The fourth and last hypothesis proposes that when small and medium factories adopt leagile manufacturing practice, they are able to improve their performance. This assertion is confirmed if the hypothesis is accepted.
The paper is structured as follows. First, in attempt to investigate these hypotheses, a great deal of attention is first paid to literature review expounding on time-based manufacturing practices and their contribution. The second section depicts time-based manufacturing model in a context of developing countries.
The third section presents the methodology. The fourth section presents the results and discussion thereof. The paper ends with the conclusion and recommendation.

Literature Review
All manufacturers in any industry focus on the end-user as stepping stone toward profit maximization [22]. In order to achieve this, managers of factories continuously develop new practices as others fade away in trying to be both value qualifiers and winners [23]. As a continuum of innovative strategies is devel-  [26]. In particular, with the conceptual lenses, Webster's Dictionary makes a clear distinction between lean and agile referring lean as a paradigm that contains "little fat" and agile as a practice that emphasizes nimbleness [18]. Proponents of leagile manufacturing argue that lean practices focus at make-to-stock operations, while agile practices are for make-to-order operations. In other word, the two can be combined to simultaneously stimulate assemble-to-order operations [18].
Other authors view the practices of lean, agile and leagile in progression and complementary in nature as they burgeoned differently in different times [27].
Lean practices for instance, were first introduced in the production of Toyota in the 1970s. As markets became more unpredictable, flexibility and responsiveness became the main concerns. In the end, numerous market forces rendered lean practice as non-competitive and unsustainable strategy [15] [28]. In USA, practitioners and academicians on realizing new trends in competition in late 1990's, re-assessed lean manufacturing practices and developed a more sophisticated manufacturing paradigm called, agile manufacturing. The focus of this new era of manufacturing goes beyond ensuring continuity, but rather exploiting opportunities, raising the clock rate and reinforcing resilience to daily shock. The N. Nagaaba key aspects at forefront included: a customer is a priority and change is an opportunity for improvement [28] [29]. In late 20 th century, manufacturers' attention focused on how to integrate lean and agile philosophies in managing manufacturing operations with the main focus of growth and sustainability [30].
These new strategies have raised a number of queries. For example, is it possible for the new wave of manufacturing characterized by more than one strategy to create competitive advantage? In terms of application, are these strategies mutually exclusive or complementary in nature? These unanswered questions stampeded into controversies among scholars and thus quest for hybrid approach referred to as "leagility", designed to take advantage of both lean and agile practices [3].
Other scholars connote that a leagile infrastructure demonstrates a cost effective supply chain [27]. Arnab [14] adds that optimization of lean and agile practices requires an IT enabling infrastructure in order to build a strong supply chain. Denise [4] points out that leagilitiy of a manufacturing firm is determined by the extent to which upstream and downstream partners are linked in converting the basic commodity into final product. His argument is premised on differing philosophical orientations of agile and lean practices at different echelons of entire supply chain. In sum, leagile model provides a logical approach that identifies and concentrates on value adding activities. Despites contradicting emphases of leanness and agility [9], recent explorations show that the most compelling reasoning behind integrating lean and agile manufacturing lies in the cost structure and the benefits of adding customer value in a sustainable manner.
Furthermore, Mason-Jones, Naylor, & Towill [7] argued that leagility is only anchored by successful adoption of lean and agile principles. It is on this development that Thaeir [13] advocates for decoupling point which allows concurrent implementation of both practices. Scholarly attempts have been made to throw more light on how lean and agile work together especially in areas of inventory and capacity. On contrary, the fundamental concern in this paper is on compe-

Time-Based Manufacturing Model in a Context of Developing Countries
Notwithstanding Due to drastic changing demands; factories have redirected their strategies towards sophisticated manufacturing tactics [31]. In order to remain on the contour of competition, SMFs move away from long term to short-term engagements to allow alternative streams of growth opportunities. As acknowledged by Arnab [14], changes in customer demand calls for innovative strategies

Core Competences
The organizational core competences exist at the corporate level and are embedded in cross-business interactions and governance structures [33] [34]. One way of supplementing internal assets and capabilities is to share core competences [35] [36]. This can only be explained by the extent to which firms agree with other parties to pursue the common set of objectives without necessarily having legal attachment but rather maintaining independence among parties [37]. Steffen, et al. [38] elude that for the organization to achieve high level of flexibility, organizational framework must be aligned. Thus, even though employees play a number of roles in a factory, they must be enabled by technology especially in dissemination of information. Warren [39] also states that specialization and bureaucratization intensify with a sense of ties between local and large organizations. From a system theoretical vantage, such ties and alliances are bound to be identifiable and recognized and virtually express overarching domination of resource [37]. Considering the notion of homeostasis, a supply chain will not be interfered with, if firms continue gaining access to the certain resource pool [40]. This is a key aspect in manufacturing industry especially in developing countries where resources are inappropriate. It allows promulgation of lean culture. Therefore, SMFs gazed at in this study need to keenly observe the nature of affiliation and alliance not to indulge themselves in unsustainable struggle in case of sudden changes in the "big fish" affiliates.

N. Nagaaba American Journal of Operations Research
Hong-Chang, Rong, & Song [34] also assert that core competences are established by appropriate managerial structure and how well production factors relate in terms of time and space. Certain aspects like, locus of decision making and levels of communication have been identified as essential elements of lean production. However, a successful lean production is manifested in a structure with strong sense of autonomy among teams and self-reliance. These doctrines continue to be emphasized under organic structure of postindustrial mode of manufacturing [41].

Operational Competences
To quicken customer service, production systems must be realigned with ad- with innovative technological, ability to fulfill customer specifications in correct quantities and in a timely manner is impractical [14]. As the next best alternative, manufacturer in the context of this study opt for imitation of imported technologies though it requires specific training of workers for specific tasks as recommended by Ketokivi & Schroeder [20]. Further explorations indicate that information technology and organizational culture expedite customer service.
For instance, Steffen, et al. [38] and Narasimhan, Swink, & Kim [45] argue that flexible production can be instigated when employees are involved in so called grey collar work. This in end creates deeper insights into their working environment. However, such motives should not be taken out-rightly as stimuli for agile culture. Instead, they spice agile manufacturing process [42] [44].

Business Transaction Competences
Manufacturing business is increasingly becoming diverse and unpredictable [23]. For a factory to stand the test of time, the entire supply chain must be engaged [27]. In addition, the whistle brow for factory performance has awakened new wave of competence mix. As new demands come along, business partners tend to share resource and task among business partners [46]. Li [7]. Under this theme, two Canadian economics Hymer [48] and McManus [49] postulate the importance of internal sourcing using a theoretical lens of internalization. Dunning [50] further relates this theory with organizational and acknowledges ownership advantage. Therefore, building on this theoretical background, factories can only exploit growth opportunities by internalizing capabilities and component instead of outsourcing. In the end, this builds confidence, trust and ownership within the entire supply chain.
In addition, when business environment is volatile, transaction costs tend to be high [31]. Therefore, short term contract and engagements allow flexible operations. This is one of the common characteristics of SMFs that renders them more competitive than large firms due to smaller chain of command. As prior researches emphasize, factories can only establish growth streams, when agility and lean competences are exhibited successfully at different stages in a supply chain [32]. As suggested in the model (Figure 1), factories are encouraged to identify and demarcate their core, operational and business transaction competences to effectively instigate a time-based manufacturing culture.
Although the literature describes a nexus of strategies and how they have been interchangeably used in manufacturing process, no apparent research efforts have been made to test the extent to which leagile practices relate to leanness, agility under certain conditions. Nonetheless, empirical evidences explaining extent to which leagile manufacturing influence factory performance, are none existent in this context. In order to widen the scope of knowledge regarding time-based manufacturing practices, an appropriate methodological approach in the following section has been adopted to address the objectives of study.

Operational Competences
Operational competences that enable agile manufacturing were measured based on agile model of [57]. Given that the center nerve of agile manufacturing is customer centricity; operational competences are conceptualized based on two enabling factors that expedite customer service: information technology and organizational culture. In each case three items were generated. In this regard data obtained were related to degree of utilizing of information technology and the extent to which organization culture is inculcated. The literature on agile manufacturing environment was used to identify likert scale items for each dimension.
The measurement of operational competence was further verified for internal consistence using Cronbach's reliability alpha. The results indicated that the Cronbach's α for the 12 items was 0.876.

Business Transaction Competences
The measurements of this combinative paradigm focus on the operation of entire supply chain [3] [58] [59]. Therefore, theoretical insights and empirical evidences of previous research were profoundly utilized in developing the measurement scale. The items that were captured here were distinctly generated.
Consequently, two dimensions were used to reflect leagile manufacturing practices. These are: Short-term contracts and Internalization. In this study, data on these aspects were also obtained by asking the respondents to rate on a five-point Likert scale the level of implementing short term contract and internalizing transactions. The measure was further tested for internal consistence and Cronbach's coefficient determined. The results indicate that the construct is reliable with 5 items whose coefficient was 0.724.

Factory Performance
To measure factory performance, extant literature was adopted. Perceptual data was utilized regarding responsiveness and reduction of cost of conversion. Although perceptual data is regarded as subjective, Ketokivi and Schroeder [20] recommend it as the most viable alternative in absence of the objective data.
What is important is the extent to which such data is subjected to rigorous reliability tests. In this case, data on responsiveness and cost of conversion were obtained by asking the respondents to indicate on a five-point Likert Scale the extent to which they agree with the statement provided. It was also deemed neces-

Data Collection
The quality of the data obtained in a survey research design, largely depends on knowledge of the respondents and diversity of the industry [1].

Analysis of Data
The analysis of data was performed using SPSS version 23. All structural equation modeling analyses were conducted using AMOS 22. Structural equation modeling was used for the following reasons: First, the fact that it can examine a series of dependence relationships simultaneously at the same time it provides statistical efficiency. Secondly, confirmatory factor analysis emphasizes stricter interpretation of unidimensionality than traditional methods [61]. Thirdly, with structural model, one can be able to analyze the relationships among multiple exogenous and endogenous variables and between endogenous variables simultaneously.
In order to achieve all the objectives, three stages of multivariate analysis were followed. First, dimensionality was assessed using principal component analysis

Results
The first objective hypothesizes that enabling competences of agile, lean and leagile manufacturing are threefold and distinct. The mean scores and standard deviations for all items are provided in  Multidimensionality of the competences was further validated using composite reliability, convergent and discriminant validity. The results are presented in Table 2 below. The results indicate that the average variance extracted (AVE) for each construct exceeds the threshold of convergent validity of 0.5. In addition, discriminant validity was tested by comparing the average variance extracted with the squared correlation between constructs [65]. Ziat [65] connotes that discriminant validity exists if the observed variables share more common variance with their respective latent construct than any other inter-construct variances. Therefore, the AVE for a construct should be higher than the squared N. Nagaaba  The values for correlations between the latent constructs (below the diagonal) also indicated that three competences are inter-related and distinct. Likewise, the respective composite reliability indices are above the threshold of 0.6. Core competences (CO) (0.910), Operational competences (OC) (0.910), and Business Transaction competences (BTC) (0.898).
In conclusion, CFA, confirms the H 1 . Enabling competences of time-based manufacturing are multidimensional and distinct in nature. As indicated in objective 1, this was psychometrically achieved with reliability, convergent validity and discriminant validity and composite reliability. The second hypothesis concerns whether time-based manufacturing practices are operationally distinct from each other in the context of Ugandan factories. To address this, the data was also first subjected to principal component analysis to determine and validate the underlying structure of time-based manufacturing. PCA was performed at instrument development phase to ascertain factory-managers' knowledge about the unique orientations of lean, agile and leagile in Uganda. Of the 30 items of time-based manufacturing generated, only 21 loaded with minimum score of 0.5 to 3 specific practice. 9 items failed to load into any practices. Meaning that they did not generate any meaning to the managers regarding lean production, agile manufacturing or leagile manufacturing. Three practices as indicated in the extant literature were extracted from the data. The PCA results are presented in Table 1.
To further test the validity of the subjective measures of lean production, agile manufacturing and leagile manufacturing, confirmatory factor analysis procedures were performed as recommended by Joseph, William, Barry, & Rolph [66]. Confirmatory factor analysis resulted into elimination of some items or factors explaining certain practices. After careful review of the items for each practice, a few problematic items were identified and deleted. In this case, LN2, LN3, LN7, LN9, LN10, LG7 and AG5, AG6, AG7 were respectively eliminated from lean, leagile and agile scales and statistically the elimination of some items did not affect the validity of the model but rather improved it.
Comparative fit index (CFI) was assessed and values more than 0.80 indicates a good fit. The root mean square error of approximation (RMSEA) was also calculated, and it was within the recommended range [66]. The relative chi-square was estimated. This estimates the errors present versus the number of parameters estimated. The low ratio of utmost 2 indicates a better model. The trimmed model subsequently had a CFI of 0.938, χ 2 = 103.145, 62 d.f., RMSEA = 0.081, χ 2 /d.f. 1.664 and without error terms that are significantly related.
The result depicted in Figure 3 shows that the three practices; lean (Ln), agile (Ag) and leagile (Lg) are related to time-based manufacturing. Further evidence of convergent validity, average variance extracted and discriminant validity was provided through examination of standardized coefficients between observed variables and the latent constructs.
While assessing discriminant validity, the square root of the average variance extracted (AVE) is compared with the correlation of latent constructs. For this study, individual time-based manufacturing practice should explain better the variance of their own exogenous variables rather than the variance of other practices [67]. The extent to which time-based manufacturing practices are discriminant is indicated by the fact that all the square root values of AVE for each practice indicated along the diagonal in Table 3 are more than their correlations with other practices. The AVE details for Lean, agile and leagile manufacturing practices are indicated in Table 3 below.  Internal consistence reliability between indicators of individual practices was assessed using composite reliability index. In this case, all the three measurement models are having the required composite reliability. The composite reliability indices were above 0.6. The composite reliability indices for lean, agile and leagile manufacturing practices are respectively, 0.778, 0.780 and 0.846 respectively as indicated in Table 3 above. The results satisfactorily justify that time-based manufacturing is threefold in the context of factories in Uganda. Therefore, the second objective of the study was fulfilled.
The third hypothesis (H 3 ) suggested that the lean and agile initiatives build a strong leagile manufacturing system. On establishing the measurement model for individual practices of lean, agile and leagile, the path coefficients were later examined. Although the three practices are related but distinct, it is also important to assess the extent to which lean and agile initiatives facilitate successful implementation of leagile practice using structural equation model in Figure 4. Using the model in Figure 4, the extent to which lean and agile practices stimulate leagile practices is assessed. In addition, withstanding the fact that lean, agile and leagile are in progression, the indirect effect of the lean on leagile via agile manufacturing is also determined. The result revealed a sufficient model-to-data fit (χ 2 = 170.59, 100 df., TLI = 0.867, CFI = 0.902, RMSEA = 0.083, and χ 2 /d.f = 1.706). In attempt to validate the structure model, items for responsiveness (FP4, FP5, FP6, FP7) were eliminated as they did not fit the model. The path analysis results indicate that lean is strongly related to leagile manufacturing compared to agile manufacturing. The standardized path coefficient for lean was positive and significant (β = 0.64, p < 0.001). Agile manufacturing does not significantly explain leagile manufacturing practices (β = −0.109, p > 0.1).
Further analyze was made on the mediating effect agile manufacturing practice. Even though not hypothesized, the results in Table 4 indicate that agile does not exercise a partial mediation effect between lean and leagile manufacturing practices. This implies that the choice of implementation of leagile manufacturing practices is not pivotal on agile manufacturing practices. Rather, leagile manufacturing is significantly driven by establishments of lean system.
The fourth and last hypothesis (H 4 ) states that there a positive and significant relationship between leagile manufacturing and factory performance of small

Discussion of Results
In the study, the underlying competences that uniquely enable adoption of In the case of lean, it is important to note that lean is built on high level of learning, communication standard procedure, ties and alliances, to fulfil customer expectations at low cost. Yet such competences are intangible resources that are not easily imitated. This is in line with Rajesh, Suresh, & Deshmukh [9] who argued that core competences stimulate high level of leanness. Again, the view of Wong and Aspinwall [68] is that the foundation of factories' competence shifted from physical and tangible resources to knowledge. The implication is that when factories in Uganda emphasize knowledge transfers and sharing with large-scale manufacturers, they are likely to adopt lean principles successfully. In addition, partnerships with government agencies and other organization seems to build strong foundation for the implementation of lean principles. These efforts should also aim at intensifying the intellectual work force through cross-training to enable them understand a number of processes in manufacturing industry.
On the other hand, operational competences were constructed based on information technology and organizational culture. This is in line with the fact that, the global manufacturing model indicates that successful agile system is based on integration of IT, knowledge management and organization culture [69]. The affirmed measurement scale for operational competences allows factories to boost their strength through agility. In Uganda, the collaborative nature of the partners in manufacturing equips them to serve the customer expeditiously. This however, can continue to boost their operations if all stake holders have full understanding of the factory systems and processes as emphasized by Abraham, Y Nahm; Mark, A Vonderembse; Xenophon, A Koufteros [11].
Lastly, business transaction competences were confirmed as unique enablers of leagile manufacturing. The discriminating nature of the measurement scale reveals that central principle in adopting leagile manufacturing lies in internalization and short-term contracts. These principles form the nerve center of entire factory by eliminating the trade-offs between lean and agile. Therefore, the factories in Uganda should emphasize short-term contracts and business engagements, internal sourcing and establishment of appropriate communication channels to tap into resources and leverage them to create a leagile system. This is in line with Klaus, Ram, & Rajneesh [70] argument that internalization and information sharing stimulate distinctive identity and thus reconciles conflicting forces within the system.
The second objective sought to establish whether time-based manufacturing practices of lean, agile and leagile are distinct concepts in context of Uganda.
The results were affirmative. The PCA and CFA confirmed the multi-dimensional N. Nagaaba nature of three factor structure in the context of Uganda. In addition, internal consistence and composite reliability were adequate. This confirmed that the lean, agile and leagile practices are distinct but related. The relationship between observed variables and their respective latent constructs was further confirmed with convergent and average variance extracted score that were within the accepted rages. This could mean that time-based manufacturing practices of lean, agile and leagile are related but with different emphases.
The third objective aimed at determining the extent to which lean and agile manufacturing practices contribute to the establishment of a leagile manufacturing system. This claim was partially supported in the context of Uganda. On satisfying data-to-fit adequacy and validity requirement of the model, the result revealed that only lean practice predicts leagile practices. Even though lean and agile share some commonalities as connoted by Rajesh & Charlene [71], the revelation from this study indicates that their strength of influence upon establishment of leagile manufacturing practice differ. The results are contrary to the theoretical connotation on leagile system where lean and agile are perceived as mutually supportive paradigms [13] [14]. The implication is that for factories in Uganda to embrace both lean and agile systems, all the partners in the supply chain have to be included in the entire process. In this case, the integrated supply chain would remove all the boundaries to allow smooth flow of materials, resources and information. The result further discloses that adoption of leagile system is grounded in value stream that aim at eliminating waste without considering customer service. Though it may sound peculiar, it is also important to know that leanness is over-arching concept that is compatible with any production system. This is in agreement with Katayama & Bennett [72]. Withstanding the finding of current research, and the fact that lean and agile easily operate at different echelons in a supply chain [18], factories implementing leagile systems should emphasize more of leanness than agility and leagility.
In addition, mediated effect of agile to leagile was found to be statistically insignificant even though data-to-fit indices were within acceptable ranges. By including agile manufacturing factor and examining its indirect involvement in stimulating leagile practices, the mediation impact was not significant. The results revealed no improvement in the standardized coefficient of agile on leagile practice. This is contrary to the progressive nature of time-based manufacturing practices as connoted by Mattias & Jan [18] and Nagaaba & Ayebale [2]. This theoretical connotation is not supported probably due to the fact that lean stimulate any production strategy. In addition, from the linear phase of organizational development, Lean and agile are considered as primary strategies yet agile is considered occasionally due to certain circumstances [6]. Therefore, small and medium factories with in Uganda should first instill lean practices of manufacturing and other practices later as they grow.
The fourth and last objective aimed at determining the predictive power of leagile manufacturing practice on factory performance. The data did not support American Journal of Operations Research this assertion significantly. The structural equation modeling revealed that leagile manufacturing practice is not a predictor of factory performance in this context. The model allows small and medium factories to adopt leagile manufacturing, but the empirical findings do not support them if they are to reduce cost of conversion. This is in line with the finding of Nagaaba [5] which indicated that leagile manufacturing does not influence the level of firm's performance in developing countries. The surprising results could probably be due to the measurement model of factory performance that does not realm with key aspects of leagile manufacturing which include independence of units, delayed production and coordinated flow of components. In addition, as small and medium factories delay production until orders are placed, the delays may come with other storage related costs. Perhaps, the development of a coordinated flow of components as emphasized in a leagile system seems not to generate any benefit to the factories. This is probably due seasonality in agro processing factories whose major raw material are agricultural. The fact that agriculture still forms backbone of Uganda's production economy, over reliance of small and medium factories on agriculture inputs is not a surprise.

Conclusion and Recommendation
The main objective of this paper was to assess the competences that enable time-based manufacturing practices and the impact of leagile practice on factory performance. Findings indicate that each of the practice (lean, agile and leagile) was enabled by its unique competences in the context of Uganda. In addition, even though lean, agile and leagile practice blend similar attributes, they offer different manufacturing capabilities. In this case, efforts were rendered to critically validate the multi-dimensional nature of competences and time-based manufacturing practices. In all cases, the data-to-fit indices were within the acceptable range rendering the measurement model reliable and adequate. Further attempt was made to determine the mediating role of agile between lean and leagile. The results did not support the assertion. The predictive power of leagile manufacturing practice on factory performance was determined although was not supported by the data. This implied that the leagile model can probably apply in a particular category of industry. Particularly when large factories employ principles of leagile manufacturing, they would benefit more than the small and

Conflicts of Interest
The author declares no conflicts of interest regarding the publication of this paper.