Development and Demonstration of Australian First Working Sodium Guide Star Laser

The Australian first working sodium guide star laser system has been designed and developed for various astronomical and space-related applications. A completely diode-pumped pulsed system was developed initially followed by a largely fiber-based continuous wave (CW) system operating at 589 nm achieved through a unique wavelength conversion scheme by combining 1342 and 1050 nm through a sum frequency generation process. For the CW system, single-mode laser beams at both 1342 and 1050 nm are achieved from fi-ber-based seed oscillators and fiber amplifiers. The output power of ~25 W at 1342 nm is achieved from a single frequency fiber Raman amplifier. Output power up to 70 W at 1050 nm is achieved from a Yb-doped fiber pre-amplifier followed by a Yb-doped fiber power amplifier. For the sum frequency generation process, optimum focusing parameters are evaluated and determined. The CW system has generated more than 20 W output power at 589 nm, a circularly polarised beam with a good beam quality, spectral linewidth ≤ 2 MHz, and the laser output locked on the sodium D 2 line at 589.159 nm. The system has been successfully demonstrated at EOS Space Research Centre, Mt Stromlo, Canberra, and become the Australian first working sodium guide star laser system.


Introduction
More than 60 years after astronomer Horace Babcock proposed the concept of Adaptive Optics (AO) as a method for improving the resolution of astronomical telescopes by compensating optical distortions introduced by the atmosphere, Optics and Photonics Journal AO systems have become practical due to significant progress made in laser, optics and sensor technologies. EOS acquired our own 177-channel and 107.6 mm diameter deformable mirror with an integrated tip-tilt stage in 2009. Now most advanced and ground-based large astronomical telescopes such as Gemini North, Gemini South, and Keck are equipped with AO systems in combination with a laser guide star which is the essential part of AO systems. The most efficient laser guide star mechanism has been the resonant scattering from sodium ions in the mesosphere at an altitude of around 90 km with an average thickness of 10 km. An efficient laser operating at the sodium D 2 resonance line close to 589 nm resonantly pumps the sodium ions generating resonance fluorescence and providing a bright artificial beacon.
Laser excitation of the mesospheric sodium layer is a complex matter and has been the subject of extensive studies for guide star applications [1] for many years. The sodium column density in the mesospheric layer is rather low (~5 × 10 13 atoms/m 2 ) and varies with seasons and locations, the spectral linewidth of the sodium D 2 line is quite narrow, only ~3 GHz [2], and these mean that careful attention needs to be paid to the format and characters of the laser technologies chosen to ensure the efficient photon returns. The amount of resonant photon returns from the sodium layer depends on many factors, including if the laser is pulsed or continuous wave (CW), the spectral linewidth, the beam quality, and the polarization properties, rather than the output power of the laser alone.
The main challenge associated with sodium guide star laser technology is to produce the laser output that is spectrally narrow and stable so it can always stay inside the D 2 line and powerful enough so sufficient photon returns can be generated with a good signal to noise ratio for the wave-front sensors.
A guide star laser program has been initiated within EOS with the primary objective of developing a field-deployable laser system capable of generating efficient laser output at the sodium D 2 line for astronomical and space-related applications. The latest sodium guide star laser developed is a CW system and has achieved more than 20 W output power at 589 nm with the laser output locked on the sodium D 2 line while maintaining a good beam quality inside the temporary enclosure mounted on the telescope. The 589 nm wavelength output is achieved through a unique wavelength conversion scheme by combining 1342 and 1050 nm laser beams through Sum Frequency Generation (SFG) process. In early 2021 the Australian first sodium laser guide star system has been demonstrated successfully at EOS Space Research Centre, Mt Stromlo, Canberra.
In the following sections, the descriptions of the laser, different laser technologies developed, system characterizations, test results and a summary of future plans will be provided.

Determination of System Configuration and Gain Media
where ω 1 is the input frequency-1, ω 2 is the input frequency-2, and ω out is the output frequency.
There are several approaches to getting 589 nm output through the SFG process, including single-pass SFG using Periodically Poled MgO-doped Stoichiometric Lithium Tantalate (PP-MgO:SLT) crystals and ring cavity resonant SFG using bulk Lithium Triborate (LBO) crystals. Different approaches have their own advantages. The ring cavity resonant SFG offers higher conversion efficiency (>60%) but requires complex cavity control and single frequency locking electronics. Single-pass SFG offers lower conversion efficiency (30% -40%) but does not require complex control electronics. We investigated both approaches and adopted single pass SFG using PP-MgO:SLT crystals for both pulsed and CW laser formats.
Generating a sufficient sodium laser guide star depends on the suitable laser format and many other operating parameters of the laser. The laser power needs to be delivered in diffraction-limited beams. In addition to a suitable laser format, many other optical, electronic, and optomechanical technologies and assemblies are required for developing a practical and reliable sodium guide star laser system.

System Development
So far 2 generations, a completely diode-pumped pulsed system, and a largely fiber-based CW system have been designed, developed, and tested. The pulsed system can provide a broader spectral linewidth and the CW system offers higher output power with narrower spectral linewidth.

A Completely Diode-Pumped Pulsed System
~15 years ago in the AO and guide star laser communities there was a strong belief that CW lasers tend to saturate the sodium ions easily and are not good for generating efficient photon returns if the spectral linewidth is less than 20 MHz.
While one of the natures of pulsed lasers is that they normally provide broader spectral linewidth so it was believed that they should be resistant to saturation and should be able to return more signal photons per watt of transmitted laser power than that obtained using CW lasers [ • Wavelength tuning and stabilization, • Single frequency monitoring, stabilization, and locking on the sodium spectral absorption line using the linear magneto-optics technique, • Timing stabilization assembly for improving the temporal overlapping of two laser pulse trains at two laser wavelengths, • Beam pointing stability control assembly for improving the spatial overlapping of two laser beams at two laser wavelengths.
It is well known that the 1319 nm spectral line of Nd:YAG is of low gain. It has an emission cross-section of ~0.95 × 10 −19 cm 2 [9] so a lot of pump radiation is transferred into heat in the process of generating 1319 nm output which leads to issues such as thermal lensing, thermally induced birefringence, and depolarization in the gain media for the 1319 nm oscillator and amplifiers. The thermal lensing, birefringence, and depolarization lead to beam wander. The beam wanders consequently makes the SFG process difficult. In order to address these issues, several rounds of investigations and experiments, including developing oscillators and amplifiers for 1319 nm spectral lines using the most advanced solid-state laser technologies, thin disks, and composite rods have been conducted.
Experiments to evaluate and compare the performance of thin disk and composite rod based oscillators and amplifiers to see which one is the best for effectively compensating and minimizing the birefringence and depolarisation, efficient power generation, and producing the best beam quality for 1319 nm spectral line with minimal beam wander have also been conducted.
A series of 10 mm diameter single crystal and ceramic Nd:YAG thin disks with Nd-doping concentration between 1.3% to 4%, and disk thickness between 100 to 150 µm have been designed, manufactured, and tested.
Several types of composite Nd:YAG rods-2 mm and 3 mm diameters with different barrel finishes, such as micro-scratches barrels have been investigated and it has been found that the amount of thermal lensing, birefringence, depolarisation, and consequently the amount of beam wander increased with the increase of the diameter of the composite rods. For achieving higher output power a larger diameter of the gain media is required because of the surface damage threshold which is measured in terms of power density, W/cm 2 . On the other hand, a larger diameter would make the thermal lensing, birefringence, depolarisation, and consequently the beam wander worse.
Both the 2 mm and 3 mm diameter Nd:YAG rods were actively cooled using deionized water flowing longitudinally. For the composite rods, it is important to have the sealing O-rings holding the un-doped YAG end caps.
It has been concluded that the composite rods are the best for effectively compensating and minimizing the birefringence and depolarisation, efficient power generation, and producing the best beam quality for the 1319 nm spectral More than 4 W output power at 589 nm with ~25% conversion efficiency from the IR inputs (1319 and 1064 nm) to 589 nm output has been achieved.
The laser output had the micro-pulse format-trains of 600 picosecond duration pulses separated by 10 ns. The spectral linewidth of the laser was ~600 MHz. Precise wavelength measurement and wavelength tuning using etalon were performed. A correct sodium absorption line profile was observed. Resonant fluorescence was observed at 589.158 nm in the vacuum. The key system specifications achieved are shown in Table 1.

A Largely Fiber-Based CW System
Following the investigations and experiments on the pulsed laser system, it has been concluded that the output power from the 3 mm diameter gain media is adequate for generating ~10 W pulsed output at 589 nm when the beam wander can be adequately controlled using the beam pointing stability control assembly. Average output power higher than 10 W at 589 nm has been achieved by a few groups with similar configurations but generally with poor stability and most importantly the output power degraded rapidly with time. When stable and reliable system performance with output power much higher than 10 W at 589 nm is required a more efficient gain medium that should have a higher gain around 1300 nm should be considered so less heat is generated which leads to less thermal lensing, less birefringence, less depolarization, and minimum beam wander.
Nd:YVO 4 has been identified as the new gain medium. It has an emission cross-section of ~6 × 10 −19 cm 2 at 1342 nm [10] [11], much higher than that of Nd:YAG (~0.95 × 10 −19 cm 2 ) at 1319 nm. SFG process (ω 1 + ω 2 = ω out ) requires the input wavelength-2 to be 1050 nm when the input wavelength-1 is 1342 nm in order to achieve an output wavelength of 589 nm. Fortunately, 1050 nm is within the gain profile of Yb-doped silicate fiber which has been widely used as the gain fiber for high power fiber lasers and amplifiers. Adopting Yb-doped silicate fiber as the gain material for 1050 nm also laid a solid foundation for developing a high efficiency fiber laser and amplifier chain. Based on the above considerations a unique wavelength conversion scheme by combining 1342 and 1050 nm laser beams through the SFG process to achieve 589 nm output, as shown in Figure 1 has been proposed.  [13]. There has been a certain level of saturation observed when the sodium layer is excited by single-mode CW lasers but the level of saturation is not as significant as theoretically predicted previously [14].
Based on the theoretical studies and experimental investigations, it has been decided to develop a high beam quality single-mode CW laser system with narrow spectral linewidth based on the new wavelength conversion scheme of converting 1342 and 1050 nm wavelength beams to 589 nm laser output. The system schematic is shown in Figure 2.  For the 1342 nm wavelength branch, the single frequency seed oscillator using Nd:YVO 4 as the gain medium with a spectral linewidth ≤ 2 MHz was accommodated in a temperature-controlled environment. Its output was coupled into a semiconductor pre-amplifier through a 50 m long optical fiber. The output from the pre-amplifier was then coupled into a single frequency fiber Raman amplifier through a fiber link. This branch was capable of generating up to 25 W output power at 1342 nm in a single-mode beam.
For the 1050 nm wavelength branch the single-frequency seed oscillator with a spectral linewidth < 100 kHz was also accommodated in a temperature-controlled environment with the output coupled into a Yb-doped fiber pre-amplifier followed by a Yb-doped fiber power amplifier through a 50 m long fiber. This wavelength branch can generate up to 70 W output power at 1050 nm in a single-mode beam.
Priority has been given to improving the conversion efficiency from the fundamental wavelength beams at 1342 and 1050 nm to SFG output at 589 nm. For these kinds of nonlinear conversion processes, the main challenge is to achieve good temperature uniformity along the nonlinear crystals as otherwise, we would not be able to properly phase match the nonlinear interactions. Good thermal contacts between the nonlinear crystals and their mounts are also very important for ensuring that the phase-matching conditions can be maintained across the whole length of the crystals. Different mounting mechanisms with copper, Indium foil, and thermally conductive adhesives were designed, developed, and tested. Optimal mounting mechanism using copper as the base ma- Theoretically, for sum frequency generation process using focused Gaussian beams, the optimal focusing condition is defined as the focusing parameter [15], and given by: where L is the length of the nonlinear crystal, b 1 and b 2 are the confocal parameters of the input beams inside the nonlinear crystals which are measures of the length of the focal region and are given by:  SFG output wavelength 589 nm is 36.2%.
Our CW sodium guide star laser has achieved all the key specifications as shown in Table 2.

System Performance and Demonstration
In addition to achieving more than 20 W output power at 589 nm, resonant fluorescence has been observed at 589.159 nm in the vacuum. The laser output has Optics and Photonics Journal also been locked on the sodium D 2 line. As shown in Figure 4, strong resonant fluorescence has been observed from the reference sodium cell.

Conclusion
A primarily fiber-based CW sodium guide star laser system operating at 589 nm has been successfully designed and developed following more than 10 years of theoretical and experimental investigations on different laser technologies with pulsed and CW formats with the primary objective of developing a field-deployable sodium Y. Gao et al. guide star laser system for astronomical and space-related applications. As a sodium guide star laser it has generated more than 20 W output power at 589 nm, a circularly polarised beam, spectral linewidth ≤ 2 MHz with the laser output locked on the sodium D 2 line at 589.159 nm, and achieved all the design specifications and performance objectives. The system has been successfully demonstrated at Mt Stromlo, Canberra, and become the Australian first and only working sodium guide star laser system.

Future Plan
At the moment the limiting factor for generating more power at 589 nm is the output power of the 1342 nm wavelength branch which is 25 W. The output power of the single-frequency Raman amplifier is going to be upgraded to 30 W.
The output power from the 1050 nm wavelength branch can reach more than 70 W. Theoretical simulations show that with 30 W power at 1342 nm and more than 70 W at 1050 nm, we will be able to achieve 25 W output power at 589 nm through single pass SFG using PP-MgO:SLT crystals. With 30 W at 1342 nm and more than 70 W at 1050 nm, we will be able to achieve at least 40 W output power at 589 nm through ring cavity resonant SFG using bulk LBO crystals.
Studies on the optimization of sodium laser guide star efficiency suggest that the sodium photon returns can be boosted by simultaneous excitation (re-pumping) of D 2a and D 2b lines [16]. A sideband with a frequency separation of ~1.77 GHz and ~10% of the total laser output power will be generated using a phase modulator for re-pumping the D 2b line.
Priority will be given to propagating the 589 nm laser beam through the beam transfer optics and characterizing the laser guide star in the sky as a part of the AO system. The laser beam quality in the laser enclosure, after transmitted through the beam transfer optics, the spot size of the sodium laser guide star, and the consequent photon returns will be comprehensively investigated.