Green and Sustainable Chemistry
Vol.06 No.02(2016), Article ID:66738,9 pages
10.4236/gsc.2016.62011

CO2 Capture at Room Temperature and Ambient Pressure: Isomer Effect in Room Temperature Ionic Liquid/Propanol Solutions

Hiroshi Abe*, Azusa Takeshita, Hirokazu Sudo, Koichi Akiyama, Hiroaki Kishimura

Department of Materials Science and Engineering, National Defense Academy, Yokosuka, Japan

Copyright © 2016 by authors and Scientific Research Publishing Inc.

This work is licensed under the Creative Commons Attribution International License (CC BY).

http://creativecommons.org/licenses/by/4.0/

Received 17 March 2016; accepted 22 May 2016; published 25 May 2016

ABSTRACT

A CO2 capture system without supercritical CO2 was optimized for mixtures of hydrophobic room temperature ionic liquids (RTILs) and propanol. We tested RTILs using bis(trifluoromethanesul- fonyl)imide, TFSI, anion and four quaternary ammonium cations, two quaternary phosphonium cations, and one imidazolium cation. The addition of 2-propanol into the RTILs clearly promoted the capture of normal CO2(nCO2) at ambient temperature and pressure. When combined with 2- propanol, the most efficient RTILs for nCO2 capture were N-butyl-N,N,N-trimethylammonium TFSI. This enhancement of nCO2 capture was not observed in RTIL mixtures with 1-propanol or in propanol mixtures containing other phosphonium- and imidazolium-based RTILs. The torsion angle of TFSI, which was calculated using density functional theory, is thought to be related to high nCO2 capture efficiently.

Keywords:

CO2 Capture, Room Temperature Ionic Liquids, Propanol Isomer Effect, Torsion Angle of TFSI Anion

1. Introduction

The emission of greenhouse gases, which warms the Earth’s surface and atmosphere, is an urgent global problem. Room temperature ionic liquids (RTILs) have attracted considerable attention for the capture of carbon dioxide (CO2) in efforts to counteract global warming. The capture of CO2 using an RTIL was first reported by physically dissolving supercritical CO2 (scCO2) at high temperature and pressure into 1-butyl-3-methylimidazo- lium hexafluorophosphate, [C4mim][PF6] [1] , and the pressure-CO2 molar fraction phase diagram was constructed at 40˚C. Since then, various theoretical [2] - [6] and experimental [7] - [13] investigations have been conducted to further develop techniques for CO2 capture and storage in green chemistry. Systematic studies reveal that scCO2 is highly soluble in the bis(trifluoromethanesulfonyl)imide (TFSI) anion-based RTIL [10] and the polymerization of RTILs has been shown to allow the reversible and fast sorption and desorption of normal CO2 (nCO2) [8] . To apply RTILs in actual industrial applications, developing a cost-effective system that does not require high temperature or pressure for nCO2 capture remains necessary.

As additive effect, isomer effects of alcohols in the RTILs were observed distinctly [14] - [17] . A previous study estimated the molecular interactions between RTILs and propanol on desorption time measured under vacuum [14] . The results indicated that 1-propanol interacts more strongly with RTILs than does 2-propanol. In addition, Raman spectroscopy revealed that the propanol isomer effect is related to the conformations of TFSI anion, which can exist as two stable conformers, cis (C1) and trans (C2) [18] [19] . C1 and C2 conformers of TFSI originate from the competition between the alkyl side-chain length of the Cnmim+ cation and the propanol isomer effect. Recently, butanol isomer effect was reported in [Cnmim][TFSI]-based systems with four types of butanol [17] , owing to the different hydrophobicities of four types of butanol. The upper critical solution temperatures (UCSTs) in the phase diagrams were clearly separated with increasing alkyl side-chain length of the Cnmim+ cation.

Systematic CO2 solubility experiments have demonstrated that TFSI exhibits good CO2 capture ability in pure RTILs systems [20] . Isomer effects have been observed in TFSI-based RTILs, including [Cnmim][TFSI] (2 ≤ n ≤ 10) [15] . The established binary phase diagrams and UNIQUAC (universal quasichemical) interaction parameters indicate that the interactions of 1-propanol with RTILs differ significantly from the interactions between 2-propanol and RTILs.

In this study, we optimized physical sorption of nCO2 at room temperature and ambient pressure. The dilution of RTILs with 2-propanol promoted nCO2 capture, and stabilized the liquid mixing state. The amount of captured nCO2 was related to the torsion angle of the TFSI anion, which was calculated by density functional theory (DFT). The propanol isomer effect and torsion angle of TFSI anion had critical effects on the level of nCO2 absorption in the propanol-rich region, which is desirable for decreasing the cost of carbon capture operation.

2. Materials and Methods

Hydrophobic RTILs were used in this study to prevent contamination by water from atmospheric moisture. TFSI is commonly used as the anion in hydrophobic RTILs. In this study, we tested four quaternary ammonium cations, i.e., N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium (DEME+), ethyldimethylpropylammonium, (N1123+), N,N,N-trimethyl-N-propyl ammonium (N3111+), N-trimethyl-N-butylammonium (N4111+), N-tributyl-N-me- thylammonium (N4441+) and methyltrioctylammonium (N8881+), two quaternary phosphonium cations, i.e., triethylpentylphosphonium (P2225+) and tributyl methyl phosphonium (P4441+), and one prototype cation, i.e., 1-butyl-3-methylimidazolium (C4mim+). All RTILs were obtained from IoLiTecCo.1-Propanol (99.5%) and 2- propanol (99.5%; Kanto Chemical Co.) were used as additives.

For CO2 sorption, a CO2 flowing system was assembled. A schematic of the CO2 sorption system is illustrated in Figure 1. Mixtures were put into a glass-type sample bottle (30 cc).

The sample bottle was placed on a container with flowing gas. The sample container was immersed in an ethanol bath (Yamato Scientific Co., BB301) with flowing CO2 gas (30 mL/min) for 10 min. Temperature stability was within 0.1˚C (15˚C ≤ T ≤ 30˚C). Within 5 s, the sample was moved to the electric balance (HR-202i, A & D Co.), which monitored the desorption process of nCO2. Gas selectivity testing was conducted using O2 and N2 gases.

To determine the phase diagrams of the RTIL-propanol mixtures, samples were cooled from 30˚C to −50˚C using an ethanol bath (Yamato Scientific Co., BE200). By visual cloud-point determinations, accuracy of the clouding temperatures was found to be within 0.5˚C. A liquid N2 pot was used as a supplement for further cooling. The minimum temperature (−50˚C) is limited by viscous ethanol at low temperature. The temperature was monitored by a Pt100 temperature sensor (Netsushin Co.). The cooling rate was 1.5 C/min.

The conformational stabilities of the mixtures were examined by Raman spectroscopy using a micro-Raman spectrometer (RA-07F, Seishin-Shoji) in backscattering mode equipped with a monochromator (500M, Horiba JobinYvon) and a charge-coupled device detector (Symphony, Horiba JobinYvon). Radiation at 532 nm from a

Figure 1. Schematic illustration of nCO2 sorption assembly.

Nd:YAG laser (power = 50 mW) was used as the excitation source.

3. Results and Discussion

3.1. nCO2 Capture in RTIL-Propanol Mixtures

Figure 2 shows the amount of captured nCO2 as a function of propanol concentration in the [N4111][TFSI]- propanol system at a temperature of 25˚C. The molar fraction of nCO2 was calculated as,

(1)

where nIL and are the moles of RTILs and nCO2, respectively. We did not consider the amount of propanol in this study, as propanol is relatively inexpensive compared with the RTILs. The results show that the addition of 2-propanol can promote nCO2 capture in the propanol-rich region. In contrast, 1-propanol did not enhance nCO2 capture. The value of η for the 1-propanol-based mixtures remained almost constant with changing propanol concentration; this is a typical isomer effect of propanol, as indicated by the phase diagrams [15] . The isomer effect of nCO2 capture is discussed in the next section along with liquid stability. The above tendency is also seen in other systems. The molar fractions at the points of maximum nCO2 sorption for all RTILs-propanol systems studied herein are indicated in Figure 3. Here, temperature was fixed at 25˚C. The nCO2 sorption of the 1-propanol-based mixture was larger than that of the 2-propanol one only for the [DEME][TFSI] system. Relative large values of η were obtained in the quaternary ammonium cation-based systems. In contrast, the phosphonium and imidazolium systems exhibited lower nCO2 capture abilities. The high efficiency of nCO2 capture in the quaternary ammonium cation-based systems can be attributed to the syntheses of these cations. An example of synthesis using the Halogen-free carbonate ester method [21] can be written as follows:

The scheme in Equation (2) leads to the coexistence of quaternary ammonium cation, alcohol and CO2, and provides a clue to explain the high nCO2 capture obtained using quaternary ammonium cations. We predict that the cation, CO2 and alcohol are affirmative each other. Among the RTILs used in this study, the [N4111][TFSI]- 2-propanol system provided the best nCO2 storage.

3.2. Thermal Properties of nCO2 Capture

To investigate the thermal characteristics of nCO2 capture, the η value of the [N4111][TFSI]-80 mol% 2-propanol

Figure 2. Dependence of nCO2 molar fraction, η (%), on propanol concentration, showing the propanol isomer effect at 25˚C. High nCO2 sorption is observed in the propanol-rich region.

Figure 3. Maximum nCO2 sorption in various RTILs-propanol systems. With the exception of the [DEME][TFSI]-propanol system, the 2-propanol-based mixtures have a preference for nCO2 capture. Quaternary ammonium RTILs possess relative high abilities for nCO2 capture.

system is plotted as a function of temperature in Figure 4(a). Upon cooling down to 15˚C, almost monotonic increase of η was observed. According to conventional thermodynamics, η decreases with increasing temperature. At lower temperature, CO2 absorption efficiency was elevated. In [N4111][TFSI]-propanol system, however, there is a problem of phase separation in the propanol-rich region. Figure 4(b) reveals the phase diagram of [N4111][TFSI]-1-propanol and -2-propanol. The phase diagram of [N4111][TFSI]-propanol system was constructed based on visual cloud-point determinations [14] [15] [17] . The cloud-points of 1- and 2-based mixtures are represented by red and blue closed circles, respectively. On the phase diagrams, different molecular interactions of 1- and 2-propanol was predominant, since phase separation curves are calculated using the UNIQUAC interaction parameters [15] . The UNIQUAC model has the nearest neighbor correlation. The UCST of the [N4111][TFSI]-80 mol% 2-propanol mixture was approximately 15˚C. Therefore, below 15˚C, it is impossible to use nCO2 capture in the [N4111][TFSI]-2-propanol system for industrial applications.

Phase diagram including phase instability is connected with nCO2 capture ability in the propanol-rich region

Figure 4. (a) Temperature dependence of nCO2 molar fraction (η) in [N4111][TFSI]-80 mol% 2-propanol; (b) Phase diagram of the [N4111][TFSI]-propanol system.

(Figure 2). At the UCST, the phase separation behavior could significantly influence the nCO2 capture. Generally, liquid becomes unstable as a precursor phenomenon close to phase separation. Fluctuations in the propanol concentration in the vicinity of the clouding point were not ignored. Furthermore, UCST and the critical concentration (xc = 85 mol%) in the phase diagram have significant meaning on the UCST [15] . In thermodynamics, fluctuations are critical phenomena that are enhanced at UCST and xc. In this study, the intrinsic instability of the liquid phase in the RTILs-propanol mixtures became distinct at around xc. Thus, we deduce that the unstable liquid phase in the propanol-rich region was stabilized by nCO2 sorption.

3.3. TFSI Conformation and nCO2 Capture

TFSI conformation stabilities in the RTIL-propanol mixtures were estimated by Raman spectroscopy [15] [17] - [19] [22] . The observed Raman bands were assigned as C1/C2 conformers by DFT calculations [18] [22] . As an example, the Raman spectrum of pure [N4111][TFSI] is shown in Figure 5(a). The experimental C2/C1 ratio was calculated by decomposing the Raman peaks, and the asymmetric pseudo-Voigt function was used to separate peaks. The highest level of nCO2 capture for [N4111][TFSI] was obtained at C2/C1 = 0.539. In contrast to [N4111][TFSI], the C2/C1 values of [N1123][TFSI] and [P2225][TFSI], which exhibited poor nCO2 capture abilities, were 0.853 and 0.869, respectively. For instance, the Raman spectrum of [P2225][TFSI] is displayed in Figure 5(b). Despite pure systems, the C2/C1 ratio of TFSI anion is regarded as a good indicator of nCO2 capture ability, and C2/C1 has been used to determine the mixing states of [Cnmim][TFSI]-propanol [15] and -bu- tanol [17] . In both the pure and mixed systems, the TFSI- anion conformer indicates energetically stable/unstable states in the liquid state.

DFT calculations are indispensable to interpret experimental results, although DFT calculations provide the molecular-level details on the gas phase. DFT calculations were performed using the Lee-Yang-Peer correlation (B3LYP) with the 6-31++G(d,p) basis set [23] [24] in the PC-GAMESS package [25] . In the DFT simulation box, we introduced the torsion angle (α) of TFSI anion (Figure 6(a)); the geometrical definition of α was provided

Figure 5. Raman spectrum of (a) pure [N4111][TFSI], and (b) [P2225][TFSI] at room temperature. The decomposed peaks are assigned as C1 and C2 conformers of TFSI.

Figure 6. (a) Definition of torsional angle α, (C-S-S-C) in TFSI; (b) nCO2 molar fraction (η) as a function of calculated torsion angle.

by the C-S-S-C angle. DFT calculations of the [N4111][TFSI] system were used to examine a relation between a of TFSI and molecular configurations of propanol isomer and CO2 additive (Table 1). The calculated torsion

angle is sensitive to the presence of propanol and its conformation. In pure [N4111][TFSI], α = 30.756˚; the addition of 2-propanol increased the torsion angle to 72.517˚. The effect of 2-propanol on torsion angle was larger than that of 1-propanol. These results are in agreement with previous DFT calculations. The experimentally obtained C2/C1 ratio of TFSI anion is known to reflect the stabilities of the liquid, glass, and solid phases [14] [15] [17] [26] . Thus, increased α in the [N4111][TFSI]-2-propanol mixture has significant implications for liquid state stabilization. The torsional potential of TFSI anion has two local minima at 80˚ and 280˚ [27] . Although the potential calculated between the two minima is relatively low, TFSI has a higher torsional barrier at approximately 0˚ (C1). Hence, in case of the [N4111][TFSI]-2-propanol mixture, 2-propanol causes the TFSI- anion to twist, and stabilizes energetically. In the [N4111][TFSI]-1-propanol system, α cannot reached to 70˚. The difference in α between the 1- and 2-propanol-based RTILs is directly connected to the propanol isomer effect on nCO2 capture. To clarify the nCO2-driven stabilization in the RTIL-2-propanol systems, we replotted the observed CO2 capture against the calculated α angle (Figure 6(b)). The most nCO2 capture in the [N4111]- [TFSI]-2-propanol was observed at α = 70˚. In contrast, the minimum nCO2 capture in the [N1123]-[TFSI]-2- propanol system, which is fully stabilized without the addition of 2-propanol, was shifted to lower value of α. The α dependence of η in Figure 6(b) can be explained by assuming that CO2 compensates for geometrically mismatching of TFSI conformer and additives in 2-propanol based mixtures.

3.4. Gas Selectivity of [N4111][TFSI]-2-Propanol

For actual applications, the RTIL-propanol mixtures must be gas selective. Figure 7 shows CO2, O2, and N2 sorption in the [N4111][TFSI]-80 mol% 2-propanol system at 25˚C. N2 cannot contribute to energetic stabilization in an unstable liquid system in the propanol-rich region. N2 mostly occupied in the air has the lowest sorption.

Table 1. Calculated torsion angle (α) of TFSI anion. α is strongly dependent on the presence of propanol and CO2.

Figure 7. Gas selectivity in [N4111][TFSI]-80 mol% propanol at 25˚C.

The gas selectivity in the [N4111][TFSI]-80 mol% 2-propanol system has an advantage for industrial applications. The results clearly show that CO2 is preferred in the [N4111][TFSI]-2-propanol system. CO2 selectivity was realized at ambient pressure. CO2 plays an important role for the high efficient CO2 capture system, although the mechanism remains unclear.

4. Summary

At ambient pressure and room temperature, nCO2 capture in quaternary ammonium-based RTILs is promoted by the addition of 2-propanol. The propanol isomer effect associated with nCO2 capture is revealed by the lack of enhancement in RTIL with added 1-propanol. The conformation of TFSI is regarded as a good indicator of nCO2 capture ability, since TFSI torsion angle is strongly correlated with the amount of nCO2 sorption. The increase in nCO2 sorption in the propanol-rich region is consistent with liquid instability near the UCST, as shown in the phase diagram. The [N4111][TFSI]-2-propanol mixtures provide both high nCO2 capture and gas selectivity.

Acknowledgements

We appreciate Dr. T. Takekiyo, Dr. M. Aono and Prof. Y. Yoshimura of National Defense Academy for helpful discussions.

Cite this paper

Hiroshi Abe,Azusa Takeshita,Hirokazu Sudo,Koichi Akiyama,Hiroaki Kishimura, (2016) CO2 Capture at Room Temperature and Ambient Pressure: Isomer Effect in Room Temperature Ionic Liquid/Propanol Solutions. Green and Sustainable Chemistry,06,116-124. doi: 10.4236/gsc.2016.62011

References

  1. 1. Blanchard, L.A., Hancu, D., Beckman, E.J. and Brennecke, J.F. (1999) Green Processing Using Ionic Liquids and CO2. Nature, 399, 28-29.
    http://dx.doi.org/10.1038/19887

  2. 2. Huang, X., Margulis, C.J., Li, Y. and Berne, B.J. (2005) Why Is the Partial Molar Volume of CO2 So Small When Dissolved in a Room Temperature Ionic Liquid? Structure and Dynamics of CO2 Dissolved in [Bmim+] [PF6-]. Journal of American Chemical Society, 127, 17842-17851.
    http://dx.doi.org/10.1021/ja055315z

  3. 3. Zhuo, S., Huang, Y., Peng, C., Liu, H., Hu, Y. and Jiang, J. (2010) CO2-Induced Microstructure Transition of Surfactant in Aqueous Solution: Insight from Molecular Dynamics Simulation. Journal of Physical Chemistry B, 114, 6344-6349.
    http://dx.doi.org/10.1021/jp910253b

  4. 4. Perez-Blanco, M.E. and Maginn, E.J. (2010) Molecular Dynamics Simulations of CO2 at an Ionic Liquid Interface: Adsorption, Ordering, and Interfacial Crossing. Journal of Physical Chemistry B, 114, 11827-11837.
    http://dx.doi.org/10.1021/jp103862v

  5. 5. Babarao, R., Dai, S. and Jiang, D. (2011) Understanding the High Solubility of CO2 in an Ionic Liquid with the Tetracyanoborate Anion. Journal of Physical Chemistry B, 115, 9789-9794.
    http://dx.doi.org/10.1021/jp205399r

  6. 6. Perez-Blanco, M.E. and Maginn, E.J. (2011) Molecular Dynamics Simulations of Carbon Dioxide and Water at an Ionic Liquid Interface. Journal of Physical Chemistry B, 115, 10488-10499.
    http://dx.doi.org/10.1021/jp203838j

  7. 7. Blanchard, L.A., Gu, Z. and Brennecke, J.F. (2001) High-Pressure Phase Behavior of Ionic Liquid/CO2 Systems. Journal of Physical Chemistry B, 105, 2437-2444.
    http://dx.doi.org/10.1021/jp003309d

  8. 8. Tang, J., Tang, H., Sun, W., Plancher, H., Radosza, M. and Shen, Y. (2005) Poly(ionic liquid)s: A New Material with Enhanced and Fast CO2 Absorption. Chemical Communications, 3325-3327.

  9. 9. Sakellarios, N.I. and Kazarian, S.G. (2005) Solute Partitioning between an Ionic Liquid and High-Pressure CO2 Studied with in Situ FTIR Spectroscopy. Journal of Chemical Thermodynamics, 37, 621-626.
    http://dx.doi.org/10.1016/j.jct.2005.03.022

  10. 10. Bara, J.E., Carlisle, T.K., Gabriel, C.J., Camper, D., Finotello, A., Gin, D.L. and Noble, R.D. (2009) Guide to CO2 Separations in Imidazolium-Based Room-Temperature Ionic Liquids. Industrial & Engineering Chemistry Research, 48, 2739-2751.
    http://dx.doi.org/10.1021/ie8016237

  11. 11. Kerle, D., Ludwig, R., Geiger, A. and Paschek, D. (2009) Temperature Dependence of the Solubility of Carbon Dioxide in Imidazolium-Based Ionic Liquids. Journal of Physical Chemistry B, 113, 12727-12735.
    http://dx.doi.org/10.1021/jp9055285

  12. 12. Brennecke, J.F. and Gurkan, B.E. (2010) Ionic Liquids for CO2 Capture and Emission Reduction. Journal of Physical Chemistry Letters, 1, 3459-3464.
    http://dx.doi.org/10.1021/jz1014828

  13. 13. Lei, Z., Han, J., Zhang, B., Li, Q., Zhu, J. and Chen, B. (2012) Solubility of CO2 in Binary Mixtures of Room-Temperature Ionic Liquids at High Pressures. Journal of Chemical & Engineering Data, 57, 2153-2159.
    http://dx.doi.org/10.1021/je300016q

  14. 14. Abe, H., Mori, T., Abematsu, R., Yoshimura, Y., Hatano, N., Imai, Y. and Kishimura, H. (2012) Desorption Process in Room Temperature Ionic Liquid Based-Mixtures under Vacuum. Journal of Molecular Liquids, 167, 40-46.
    http://dx.doi.org/10.1016/j.molliq.2011.12.009

  15. 15. Ozawa, S., Kishimura, H., Kitahira, S., Tamatani, K., Hirayama, K., Abe, H. and Yoshimura, Y. (2014) Isomer Effect of Propanol on Liquid-Liquid Equilibrium in Hydrophobic Room-Temperature Ionic Liquids. Chemical Physics Letters, 613, 122-126.
    http://dx.doi.org/10.1016/j.cplett.2014.09.003

  16. 16. Abe, H., Aono, M., Kameoka, S., Tsai, A-.P., Yoshimura, Y. and Ozawa, S. (2014) Impedance Spectroscopic Study Using Nanoporous Electrode on Room Temperature Ionic Liquid-Propanol Mixtures. Journal of Japan Institute of Energy, 93, 1015-1020.
    http://dx.doi.org/10.3775/jie.93.1015

  17. 17. Abe, H., Fukushima, R., Onji, M., Hirayama, K., Kishimura, H., Yoshimura, Y. and Ozawa, S. (2016) Two-Length Scale Description of Hydrophobic Room-Temperature Ionic Liquid-Alcohol Systems. Journal of Molecular Liquids, 215, 417-422.
    http://dx.doi.org/10.1016/j.molliq.2015.12.011

  18. 18. Fujii, K., Fujimori, T., Takamuku, T., Kanzaki, R., Umebayashi, Y. and Ishiguro, S. (2006) Conformational Equilibrium of Bis(trifluoromethanesulfonyl) Imide Anion of a Room-Temperature Ionic Liquid: Raman Spectroscopic Study and DFT Calculations. Journal of Physical Chemistry B, 110, 8179-8183.
    http://dx.doi.org/10.1021/jp0612477

  19. 19. Fujii, K., Soejima, Y., Kyoshoin, Y., Fukuda, S., Kanzaki, R., Umebayashi, Y., Yamaguchi, T., Ishiguro, S. and Takamuku, T. (2008) Liquid Structure of Room-Temperature Ionic Liquid, 1-Ethyl-3-methylimidazolium Bis-(trifluoromethanesulfonyl) Imide. Journal of Physical Chemistry B, 112, 4329-4336.
    http://dx.doi.org/10.1021/jp7105499

  20. 20. Muldoon, M.J., Aki, S.N.V.K., Anderson, J.L., Dixon, J.K. and Brennecke, J.F. (2007) Improving Carbon Dioxide Solubility in Ionic Liquids. Journal of Physical Chemistry B, 111, 9001-9009.
    http://dx.doi.org/10.1021/jp071897q

  21. 21. Wasserscheid, P. and Welton, T. (2003) Ionic Liquids in Synthesis. Wiley, Hoboken.

  22. 22. Lasse` gues, J.C., Grondin, J., Holomb, R. and Johansson, P. (2007) Raman and ab initio Study of the Conformational Isomerism in the 1-Ethyl-3-methyl-imidazolium Bis(trifluoromethanesulfonyl)imide Ionic Liquid. Journal of Raman Spectroscopy, 38, 551-558.
    http://dx.doi.org/10.1002/jrs.1680

  23. 23. Becke, A.D. (1993) Density-Functional Thermochemistry. III. The Role of Exact Exchange. Journal of Chemical Physics, 98, 5648-5652.
    http://dx.doi.org/10.1063/1.464913

  24. 24. Lee, C., Yang, W. and Parr, R.G. (1988) Development of the Colle-Salvetti Correlation-Energy Formula into a Functional of the Electron Density. Physical Review B, 37, 785-789.
    http://dx.doi.org/10.1103/PhysRevB.37.785

  25. 25. Schmidt, M.W., Baldridge, K.K., Boatz, .J.A., Elbert, S.T., Gordon, M.S., Jensen, J.H., Koseki, S., Matsunaga, N., Nguyen, K.A., Su, S.J., Windus, T.L., Dupuis, M. and Montgomery, J.A. (1993) General Atomic and Molecular Electronic Structure System. Journal of Computational Chemistry, 14, 1347-1363.
    http://dx.doi.org/10.1002/jcc.540141112

  26. 26. Yoshimura, Y., Takekiyo, T., Imai, Y. and Abe, H. (2012) Pressure-Induced Spectral Changes of Room-Temperature Ionic Liquid, N,N-Diethyl-N-methyl-N-(2-methoxyethyl)ammonium Bis(trifluoromethylsulfonyl)imide, [DEME][TFSI]. Journal of Physical Chemistry C, 116, 2097-2101.
    http://dx.doi.org/10.1021/jp205314f

  27. 27. Tsuzuki, S., Hayamizu, K. and Seki, S. (2010) Origin of the Low-Viscosity of [emim][(FSO2)2N] Ionic Liquid and Its Lithium Salt Mixture: Experimental and Theoretical Study of Self-Diffusion Coefficients, Conductivities, and Intermolecular Interactions. Journal of Physical Chemistry B, 114, 16329-16336.
    http://dx.doi.org/10.1021/jp106870v

NOTES

*Corresponding author.