Journal of Materials Science and Chemical Engineering, 2014, 2, 38-42
Published Online October 2014 in SciRes. http://www.scirp.org/journal/msce
http://dx.doi.org/10.4236/msce.2014.210006
How to cite this paper: Kim, H.-H., Kim, S.-Y., Kim, D.-H., Oh, C.-Y. and Jo, N.-J. (2014) Effect of Silane Coupling Agent on the
Flexural Property of Glass Fiber Reinforced Composite Film. Journal of Materials Science and Chemical Engineering, 2, 38-42.
http://dx.doi.org/10.4236/msce.2014.210006
Effect of Silane Coupling Agent on the
Flexural Property of Glass Fiber Reinforced
Composite Film
Hye-Hyun Kim, Si-Young Kim, Dae-Hee Kim, Chae-Young Oh, Nam-Ju Jo*
Department of Polymer Science & Engineering, Pusan National University, Busan, Korea
Email: *namjujo@pusan.ac.kr
Received August 2014
Abstract
Transparent glass fiber reinforced composites films ware fabricated by UV light induced chemical
crosslinking of composite materials consisting of glass fiber and UV curable resin in film state. In
order to app l y film to flexible device, excellent flexural property is required, then the delamination
should not occurred between glass fiber and UV curable resin when film is bent. To minimize
delamination and improve the interfacial adhesion at interface between glass fiber and UV curable
resin, the γ-aminopropyl triethoxy silane and γ-glycid oxypropyl trimethoxy silane were applied
for the surface treatment of glass fibers. Silanization of glass fiber surface was checked by
scanning electron microscopy and the degree of delamination of composite film was confirmed
through the bending test, ASTEM290-96a, used by haze meter.
Keywords
Glass Fiber, Silane , UV Curable Resin, Composite, Flexural Property, Haze
1. Introduction
Glass fiber is the most common reinforcing fiber for polymeric matrix composite. The principal advantages of
glass fiber are low cost, high tensile strength, high chemical resistance, and excellent insulating property. Fiber-
reinforced polymer composites have seen a rapid rise in use in the past 30 years, due to their high strength and
stiffness and light weight, compared with more traditional structural materials, such as steel and aluminum. The
reason for this superior performance is the synergistic combination of the two, or more, constituent phases. This
synergy is brought about by the interaction between the fibers and the polymeric matrix [1].
However, most of the fiber-reinforced polymer composites have been used as structural materials. They have
not been tried for application to optical films in thin film transistor (TFT) liquid crystal display or flexible sub-
strate in organic light emitting diodes (OLEDs).
For these applications, the matching of the refractive index of matrix and glass fiber should be essentially re-
quired for achieving transparent composite films. In addition, when composite film is bent, the optical property
*
Corresponding author.
H.-H. Kim et al.
39
should be equal. In other words, delamination should not be occurred between glass fiber and matrix resin, and
this phenomenon is highly related with interfacial adhesion between glass fiber and matrix [2].
It is well known that the interphase plays a key role in determining mechanical interfacial properties of com-
posites. The efficiency of the stress transfer between fibers and matrix is determined not only by molecular inte-
raction at interface, but also by the properties of the formed interphase, in particular, its thickness and strength [3]
[4].
One of the effective ways of creating interphase and, in this way, controlling composite properties is fiber
surface treatment, using sizings and film formers or coupling agents.
To improve the interfacial adhesion at interface between the glass fibers and matrix resin, silane coupling
agents were used formerly on the fibers [5]. At interface between the glass fibers and the silane coupling agent,
the hydroxyl groups of the silanes and those of the glass fiber surface can react with each other through siloxane
bonding or hydrogen bonding, as seen in Figure 1 which indicated the adhesion process of the silane coupling
agents onto glass fibers [6] [7].
The aim for this work is to find out the relationship between flexural property of composite film and optical
property as a result of composite film fabrication based on glass fiber processed by various silanes coupling
agent.
2. Experimental
2.1. Materials
E-glass fiber (56 × 56 count/25 mm, 48 g/m2) used in this work was supplied from Nittobo Asco Glass Fiber Co.
Ltd.. And e-glass fiber is treated with acrylic silane compound [8]. For the matrix resin, fluorene acrylate and
urethane acrylate were used. Both are provided from Osaka Gas Chemical Co. and SK Cytec. And 1-hydroxy
cyclohexyl phenyl ketone (HCPK) was used as photoinitiator. Silane coupling agents, γ-aminopropyltriethoxy
silane (APS) and γ-glycidoxypropyltrimethoxy silane (GPS) are purchased from Sigma Aldrich. The chemical
structures of APS and GPS are given in Figure 2.
2.2. Silanization of Glass Fiber
In order to treat silane, the glass fib er was fired at first under an ambient atmosphere at 500˚C for 2 h to burn out
the organic sizing agent coated onto its surface. Silane coupling agents were diluted to 1 wt% using the co-sol-
vents of methanol and deionized water with the ratio of methanol/water = 80/20 wt%. A silanol group is usually
unstable in the presence of water, but it is stable in weakly acidic solution. Aminosilanes and glycidylsilanes are
an exception because the amino group and glycidyl group help to stabilize the silane in water. Next, the hydro-
lysis of the silane coupling agent was carried out for 30 min, and glass fibers were dipped in the hydrolyzed si-
lane solution for 30 min. And it was dried at 110˚C for 5 min , follo w ed by 24 h at room temperature.
Figure 1. Surface structure of silane-treated glass fiber [1].
APS GPS
Figure 2. Chemical structures of the APS and GPS.
H.-H. Kim et al.
40
2.3. Composite Film Fabrication
Based on APS treated glass fiber, GPS treated glass fiber, and non-treated glass fiber (burned original glass fi-
ber), three composite films were fabricated. The procedure described below (Figure 3).
1) Matrix resin was prepared by complete mix ing with fluorene acrylate, urethane acrylate, and HCPK. 2)
Glass fiber was placed on a glass plate and impregnated with the matrix resin. 3) Sample was deaerated in a va-
cuum oven at 60˚C for 20 min. 4) The drenched sample was covered with another glass plate. 5) To obtain a
proper film thickness, the sample was pressed by laminator. 6) Sample was treated by heat treatment at 220˚C
oven for 1 h after cured both sides by metal UV lamp for 90 s.
2.4. Bending Test
Figure 4 shows schematic diagram of bending test to observe the point where delamination occurs.
This is the experiment exerted by force until the upper and bottom sides of specimen bending becomes equi-
librium. At the moment specimen delamination occurs, the flexural property of composite film is estimated by
measuring the distance between gap and haze.
2.5. Scanning Electron Microscopy (SEM)
Silanization of glass fiber surface was observed with a scanning electron microscopy (S3500N, HITACHI). The
surfaces of specimens were coated with gold to avoid charging under the electron beam.
3. Results and Discussion
Figure 5 shows SEM microphotographs of the surface of various silane-treated glass fiber. Figure 5(a) is image
of none-treated glass fiber. It has a clean surface. Figure 5(b) and Figure 5 (c) are images of glass fibers treated
by APS and GPS, respectively. As shown in Figure 5(b) and Figure 5(c), we found that APS and GPS are well
adhered to the surface of glass fiber. This indicates that the interfacial adhesion of the glass composites is im-
proved. These results could be explained by the increase of hydroxyl groups and it makes more hydrogen bond-
ing at the interfaces between the glass fiber and the silane coupling agent.
Figure 6 displays hazes of composite films treated APS and GPS silane coupling agents and non-treated de-
pending on the gap of the two plates. For composite films treated by APS and GPS coupling agents, haze started
increasing when the upper and bottom side of specimen gap becomes 8 mm. For non-treated glass fiber,
Figure 3. The manufacturing process of composite film.
H.-H. Kim et al.
41
Figure 4. Standard test method for bend testing of ma-
terial (ASTM E 290-97a).
(a) (b)
(c)
Figure 5. SEM micrographs of the glass fiber (a) non-treated glass
fiber; (b) APS; and (c) GPS-treated glass fiber.
Figure 6. Hazes of composite films treated APS and GPS coupling
agents and non-treated depending on the gap of the upper and bot-
tom side of specimen.
H.-H. Kim et al.
42
delamination started at 10 mm, shows the poorest flexural property. As a result of evaluation of flexural property,
the flexural property of composite film treated by APS coupling agent is the best. Result above is expected that
APS treated glass fiber is well compatible with flourene acrylate and urethane acrylate applied matrix resin.
4. Conclusion
For the manufacture of transparent glass fiber composite film to apply for flexible device, excellent optical
property and flexural property are significant elements. To improve the interfacial adhesion at interface between
the glass fibers and matrix resin, the various types of silane coupling agents such as γ-aminopropyl triethoxy si-
lane (APS) and γ-glycid oxypropyl trimethoxy silane (GPS) were applied. In result, the optical property and
flexural property of glass fiber composite film were highly improved by the treatment of silane coupling agent
between glass fiber and matrix resin. And APS coupling agent was suitable in this study.
Acknowledgements
This work was supported by the BK21 PLUS Centre for Advanced Chemical Technology (21A20131800002).
References
[1] Park, S.-J. and Jin, J.-S. (2001) Effect of Silane Coupling Agent on Interphase and Performance of Glass Fiber/Unsa-
turated Polyester Compoiste. Journal of Colloid and Interface Science, 242, 174-179.
http://dx.doi.org/10.1006/jcis.2001.7788
[2] Ryu, S.C., Kim, J.W. and Park, L.S. (2009) Fabrication of Glass Fiber Reinforced Composite Film for Flexible Organ-
ic Light Emitting Diode Devices. Mol. Cryst. Liq. Cryst., 514, 331-343.
[3] Agrawal, R., Saxena, N. S., Sreekala, M.S. and Thomas, S. (2000) Effect of Treatment on the Thermal Conductivity
and Thermal Iffusivity of Oil-Palm-Giber-Reinforced Phenolformaldehyde Composites. Journal of Polymer Science
Part B: Polymer Physics, 38, 916-921.
http://dx.doi.org/10.1002/(SICI)1099-0488(20000401)38:7<916::AID-POLB2>3.3.CO;2-S
[4] Mäder, E. and Pisanova, E. (2000) Characterization and Design of Interphases in Glass Giber Reinforced Polyprop-
lyene. Polymer Composites, 21, 361-368. http://dx.doi.org/10.1002/pc.10194
[5] Elley-Bristow, D.M., Bellinger, M.A., Sauer, J.A. and Hara, M. (1999) Interfacial Bonding of Silica Glass Giber to
Polystyrene Ionomers. Journal of Polymer Science Part B: Polymer Physics, 37, 2705-2710.
http://dx.doi.org/10.1002/(SICI)1099-0488(19990915)37:18<2705::AID-POLB14>3.0.CO;2-C
[6] Bayer, T., Eichhorn, K.-J., Grundke, K. and Jacobasch, H.-J. (1999) FTIR Spectroscopic Studies of Interfacial Reac-
tions between Amino Functionalized Silicon Surfaces and Molten Maleic Anhydride Copolymers. Macromolecular
Chemistry and Physics, 200, 852-857.
[7] Tragoonwichian, S., Yanumet, N. and Ishida, H. (2006) Effect of Fiber Surface Modification on the Mechanical Prop-
erties of Sisal Fiber-Reinforced Benzoxazine/Epoxy Composites Based on Aliphatic Diamine Benzoxazine. Journal of
Applied Polymer Science, 106, 2925-2935. http://dx.doi.org/10.1002/app.25797
[8] Shibahara, S., Shimobe, Y. and Kuramoto, H. EP Patent NO.1477529A1.