Received 9 June 2016; accepted 31 July 2016; published 3 August 2016

ABSTRACT

Cranes are used in many industries to transport heavy loads from one position to another. These loads are fastened to a crane hook which makes it a critical aspect of the crane itself. The purpose of this study is to optimize the performance of the crane hook based on stress, geometry, and weight. A single load is considered and multiple cross sections―including square, circular, and trapezoidal―are analyzed. The analysis takes the form of theoretical calculations and finite element analysis through the use of SOLIDWORKS Simulation. The trapezoidal cross section is determined to be the most efficient and the weight and stress of this cross section are optimized by varying the cross sectional parameters.

Keywords:

Crane-Hook, Geometric Properties

1. Introduction

The stress and deflection in the crane hooks for this study are determined both using theoretical calculations as well as finite element analysis simulation in SOLIDWORKS. The theoretical calculations are based on Figure 1 shown below. It is possible to calculate the eccentricity (e) and normal stress (σ) in a curved hook based on Equation (1) and Equation (2), respectively. The neutral radius (r_n) and eccentricity are determined based on the different cross sections shown in Figure 2. Square, trapezoidal, and circular cross sections are considered in this study [1] .

(1)

(2)

2. Results

2.1. Cross Section Selection

The concept of loading a curved beam is used to determine the maximum stress and displacement in multiple cross section shapes including square, circular, and trapezoidal. A common cross sectional area and hook radius are used for all geometric selections and each cross sections centroid lies on the radius of curvature. The cross sections along with the parameters used for testing are shown in Figure 3.

These three cross sections are used to create solid models of a hook that has a radius of curvature of 4 in. The resulting solid models are used to perform finite element analysis in SOLIDWORKS. In this finite element analysis, a load of 8000 lbs is considered and the resulting normal stress and deflection are analyzed. The finite element models shown in Figures 4-6 indicate the location of maximum stress, and Figures 7-9 show the de-

flection. These results are summarized in Table 1. These results show that the trapezoid cross section has the most desirable performance due to the lower levels of stress and deflection in comparison to the square and circular cross sections [2] .

2.2. Cross Section Optimization

It is possible to determine the optimal geometric properties with the trapezoidal cross section selected. The parameters of the trapezoidal cross section detail in Figure 3 are varied to determine the values that provide the optimal performance. In order to achieve this, the value of the neutral radius (r_n) is held constant at 3.5 in, while the values of h, b_i, and b_o are varied simultaneously. The materials being considered in this optimization are A-36 steel, 6061-T6 Aluminum, and Ti-6AL-4V Titanium and their properties are shown in Table 2 [3] - [5] . By selecting 7 values of the parameter ℎ, it is possible to determine values of b_i, and b_o such that the weight is minimized and the maximum normal stress is constrained to one half of the materials yield strength (σ_y). The results of this optimization are shown in Figure 10. Exact parameter values are shown in Tables A1-A3 in Appendix A [6] [7] .

3. Conclusions

The results of this research show that for a given cross sectional area, a trapezoid cross section of a hook will have better performance in terms of maximum stress than a circular or square cross section. It is also shown that as the h value of a trapezoidal hook increases, the minimum weight of the hook decreases at a decreasing rate. While the highest value for h will give the lowest weight overall, it is important to keep the proportions of the hook in mind when making the parameter selection. A very large value of h will increase the overall extents of the hook profile and create inefficiencies in packaging and will require a much larger opening on the load that is being moved.

Another observation that is made is in the difference in weight between the three materials while achieving the same goal of maintaining stress levels of one half of the materials yield strength. The percent decrease in weight between steel vs. aluminum or titanium can be as large as 80%. This indicates that in terms of performance, aluminum or titanium will be a clear choice over steel. The difference between aluminum and titanium

however is much smaller. This is where the cost of raw materials and the machinability of the material will factor heavily into the material selection decision.

Cite this paper

Niranjan Desai,Nuri Zeytinoglu, (2016) Design and Optimization of the Geometric Properties of a Crane Hook. World Journal of Engineering and Technology,04,391-397. doi: 10.4236/wjet.2016.43038

References

Appendix A

Optimized Cross Section Values