1. Introduction
Peat has been used as energy about 2000 years as substitute for firewood and heating. The use of gas and oil during the 20th has shadowed the use of peat (Andriesse, 1988) but the high demand for electricity has stimulated the construction of peat fired power plant. It was used as fuel in four countries namely former Soviet Union, Sweden, Ireland and Finland in the world in 1996 (Schora & Punwani, 1980). In Ireland for example, peat has been used for electricity generation since 1950, and it is estimated at 10% of the total installed capacity (Sarkki et al., 2012). Rwanda has approximately 155 million tones of dry peat over an area of 50,000 ha of peat (Ekono, 1992), most of which is located in South and South west of the Country. These deposits were formed about the end of the last glaciations period and this implies that they are less than 10,000 years old (Andriesse, 1988; Pajunen, 1996).
However, peat deposit in Akanyaru is 20,000 years old and thus it contains peat of glacial and postglacial period (Pajunen, 1996). These deposits were formed as a result of the formation of East Africa lift Valley which caused the Precambrian rocks of Lake Tanganyika to sink in 700 m below sea level and the Ruwenzori area to elevate to more than 5000 m above sea level and therefore it has changed the East Africa plateau. This period has triggered the formation of new lakes and flow direction of rivers. The topographical and hydrological architect of tropical swamps in Rwanda is basically influenced by recent volcanism. Because the lava flow blocked the valley, the age of these peat deposits are more likely to be influenced by volcanic activity than climate change (Andriesse, 1988). Rwanda has the operational peat power plant in Gishoma; Rusizi District generating 15 MW connected to the national electrical grid. Rwanda Cement Company uses 13,000 tons per year of wet peat; however it is still vulnerable to its limited capacity to sustain large scale peat production that could handle up to 50 MW of power (Namata, 2014). Hence, it was felt necessary to map all prospective locations of peat and their energy potential for future exploitation.
Under the aegis of the Energy division, Rwanda Ministry of Infrastructures, a comprehensive research-oriented peat program has been launched, emphasizing on quality, quantity and technology development with the following objectives:
1) Understanding the nature and distribution of peat in Rwanda
2) Identifying promising sites on regional scale and estimating the resource potential
3) Quantifying peat resources in Rwanda
4) Recommending suitable sites for peat exploitation
In recent times, interest has been given to peat deposits as probable models for certain coal deposits. Their distribution, low ash content, low sulfur and thickness have attracted coal geologists to study these peat bogs along with some brown coal deposits (Dehmer, 1993; Staub et al., 1991). Scientific research is the only way to justify if the recent peat deposit can be provided as models for certain coal basin.
2. Geological Settings
Rwanda falls into Kibaran belt (KIB) of the Central Africa which is a belt of Mezoproterozoic supracrustal units composed of metasedimentary rocks and minor metavolcanic rocks. S-types granitoid and mafic rocks (Fernandez-Alonso et al., 2012; de Clercq et al., 2008) have intruded it. The NE Kibaran Belt as it is known as Karagwe-Ankole Belt (KAB) consists of two different structural domains namely WD (Western Domain) and ED (Eastern Domain) (Figure 1) and each domain has a specific sedimentary sub-basins and depositional conditions (Fernandez-Alonso et al., 2012). The WD is referred as Akanyaru Supergroup while the ED is Kagera Supergroup. WD is composed of Rwanda, part of Katanga in DRC up to Ankole region of SW Uganda. This super group is underlain by Palaeoproterozoic basement. The older granites and gneisses dominate the eastern province while the northwestern is made up of neogene volcanics.
The young alluvium and lakes sediments dominate the southwestern part of the country (Figure 2). The sedimentary sequences indicate the influence of shallow marine and high energy environment due to stratification, conglomerates and symmetric ripple marks found within the layers. The western rift of western part of Rwanda is filled with tertiary and quaternary clastic sediments (Thomas, 2006).
3. Proximate Analysis Parameter and Calorific Value of Low Rank Coal
Peat is low rank coal, which is made of plant remains as evidenced by the presence of biomarkers detected through chemical, geological, and petrographic studies (Del Rio et al., 1992). It is sedimentary deposit formed principally from plants and rarely from inorganic substances. It is, thus, an aggregate of macerals or premacerals and minerals that when subjected to certain processes, can be converted to coal (Mugerwa et al., 2019). Coal is used for power generation, steel making, cement production, and many other purposes around the world. The billions of tons of coal are merchandised every year in local and international market. The quality of coal, the desirable purpose of use and the quantity determine its price.
The properties of coal, which have on burning and environmental performance regularly, form the basis of sale agreements, and they include calorific value, volatile matter, moisture content, sulfur, and ash content of the coal (Zhu, 2014). The main purpose of coal sample analysis is to determine quality or rank of coal. The simplest and most common form of coal evaluation is to determine moisture content, volatile matter, and ash and by difference fixed carbon with the coal sample.
3.1. Moisture Content
Coals are mined from the ground with some moisture allied with them. Slightly heating the coal samples above boiling points water (100˚C), the loss of the weight is defined as moisture content. Normally coal accounts 5% to 70% moisture content. High moisture content is not desirable because it reduces the heating value of coal. There are four forms of moisture within coal samples, which are:
1) Surface or free moisture (water held by the surface of the coal particles or macerals),
2) Residual moisture (water held by capillary action with a pore),
3) Decomposition moisture (water produced from the thermal decomposition of organic constituents of coal) and,
4) Mineral moisture (water, which comprises parts of crystal structure of hydrous silicates such as clay or inorganic minerals in coals) (Zhu, 2014).
Proximate analysis of moisture determines the total and/ or residual moisture content of coal. The total moisture content of coal consists of surface and inherent moisture content and it is measured on as received basis while residual moisture content is moisture measure on air-dried samples (Zhu, 2014; Ahmed et al., 2019). In this study, the reported moisture is residual because before measuring the moisture content the samples were air-dried.
3.2. Ash Content
Ash is the residue remaining after the combustion of coal in air and is derived from inorganic compounds existing in original coal substance and from accompanying mineral matter (Zhu, 2014). The results of analysis show the ash yield that is indicator of the grade and quality of coal since it offers amount of incombustible materials. The high ash yield, lower the calorific value of coal (Ahmed et al., 2019). According to Zhu (2014), the residue remaining after heating 1 g of coal/peat, if weighted will be equal to ash yield.
3.3. Volatile Matter
Volatile matter in a peat refers to the thermal decomposition products liberated when a peat is heated at high temperature in the absence of air. The volatile matter obtained during analysis of coal is mainly composed of combustible gases such as hydrogen, carbon monoxide, hydrocarbon, tar, ammonia and incombustible gases carbon dioxide and steam (Zhu, 2014; Ahmed et al., 2019). The VM is used to rank the coal and to establish coal-burning characteristics.
3.4. Fixed Carbon
Fixed carbon in a coal is the carbon that remains in a coal sample after volatile matter is driven off. The ratio of fixed carbon to proximate VM, the fuel ratio, is used as measure of combustion reactivity and burnout (Ahmed et al., 2019). The fixed carbon is not determined directly, it is rather calculated by subtracting from 100 the sum of moisture, VM and Ash yield (Zhu, 2014).
3.5. Calorific Value
Calorific value is a direct indication of heat content (energy value) of the coal. It is crucial parameter for coal mining and combustion and it used standard of coal quality and hence its economic value. The calorific value is the property, which defines the valuation of biomass as a fuel (Sheng & Azevedo, 2005; Ahmed et al., 2019). Therefore, once measured, it determines significantly if it can be mined as an economical and environmental energy source. Calorific Value may be measured or calculated from ultimate/proximate analysis (Ahmed et al., 2019). In this study, the calorific value was measured not calculated. The CV is defined as the amount of heat evolved when a unit weight of biomass is burnt completely and the combustion products cooled to a standard temperature of 298 K (Shirazi et al., 1995; Ahmed et al., 2019).
4. Quantitative and Qualitative of Peat Deposits in Rwanda
The coal is the product of fossilization of plant remains as evidenced by the detection of biomarkers based on chemical, geological and petrographic studies of coal (Del Rio et al., 1992). Peat is sedimentary deposit formed principally from plants and rarely from inorganic substances. It is, thus, an aggregate of macerals or pre-macerals and minerals that when subjected to certain processes, can be converted to coal. According to Cohen et al. (1987), it is difficult to place a precise boundary between what might be a precursor of carbonaceous shale and what might be a precursor of a coal. However, it is agreed that the precursor of a good coal should consist of at least 70% dry weight of organic material (Del Rio et al., 1992).
Peat is organic sediments from plants and seldom from inorganic substances deposited in situ or transported. It is subjected to different processes such as coalification to become coal (Del Rio et al., 1992). The usage of coal /peat is related to its geochemical properties. For example, coal/peat with high sulfur and high ash content is not suitable for energy production. The high sulfur content is environmentally harmful whereas the high ash yield reduces the heating value of the peat. The economic potential of fossil fuel is evaluated based on its chemical and fuel properties (Table 1).
Table 1. General chemical and fuel properties of a range of fossil fuels (modified by Theophile Mugerwa, after Lindström, 1980).
The researchers have appraised 155 million tones of peat on dry basis across the country (Hakizimana et al., 2016; Ekono, 1992) and these deposits could be converted into energy (Vitikka & Lahtinen, 2013). Table 2 shows estimated quantity from selected peat deposits. Figure 3 represents the surveyed peat deposited in Rwanda. The potential peat resources vary from one location to another.
The procedures outlined by the American Society for Testing and Materials (BIS, 2003; ASTM-E711, 1987) were followed to determine total moisture, volatile matter, ash, fixed carbon, total sulfur and calorific and some of the results are presented in Table 3. The high moisture content (average 70.88%) is typical of peats (70% - 90%). The total Sulfur % values (average 0.84%) are generally medium for all samples. The gross calorific values of peat samples ranged from 3107 to 5258 Kcal/kg, with an average value of 4302 Kcal/kg. These values are moderately very high because typical dry peat has calorific values of 2000 Kcal/kg (Hoş-Çebi & Korkmaz, 2015).
The average ash content of samples taken from different location is displayed in Table 3 where Mashya display the lowest value (20%) while the highest ash content (80%) is found in Kageyo. The average ash content in all studied location is 36%. The moisture content in all locations is slightly high ranging from 53% to 85%. Kaguhu and Kageyo display the lowest moisture content (53%) while Akanyaru North (other, South) is featured with highest value (85%). The ash content of less than 40% in soda peat dried up to 30% moisture content and less than 30% in milled peat dried to 40% is suitable for electrical power generation (Mugerwa et al., 2019).
In previous research conducted by Theophile Mugerwa (2020) and presented in Figure 4, that most of the samples are in three zones namely Mashya, Gishoma and Gihitasi fall within useful zones. Some are very useful, useful; conditional useful and other in useless zones and thus an attempt to further treatment of peats is required to use it. The usefulness may be associated with volatile matter, ash content and sulfur content. In this content, if sulfur is slightly high, there is a need to development air treatment exercise before using it. This supplement the previous research (Mugerwa et al., 2019; Hakizimana et al., 2016; EDCL, 2014) stated that Gishoma and Mashya are good deposits for peat to power.
Figure 4. Classification of usefulness of peats from Mashya, Gihitasi and Gishoma for clean coal technology based on petrographic composition (modified by authors after Bielowicz, 2013).
5. Conclusion
The peat resources are playing a crucial role in the development of Rwanda but its quality is in doubt. The quality is not enough good for electrical power plant to run for many years and thus there is a need to develop a possible way to increase quality of harvested peat that is important to ensure long-term use for electrical generation. The analysis of earlier and new data depicts the most prospective bogs which are Murago, Rucyahabi, Akanyaru, Mukindo, Ndongozi and Nyirabirande. Besides evaluating the peat resources potential, the geochemical analysis can provide inputs such as peat forming vegetation, chemical characteristics and biogeochemical processes for developing environmentally safe production technology.
Acknowledgements
The authors thank the African Union Commission through Pan African University to provide grant to carry out this research. The anonymous reviewers are also acknowledged.